Engineering topics
Bobrova, N. A.
Publications and source records attributed to Bobrova, N. A..
Creation of an axially uniform plasma channel in a laser-assisted capillary discharge
Dissipative capillary discharges form plasma channels which allow for high power laser guiding, enabling efficient electron acceleration in a laser wakefield accelerator. However, at the low plasma densities required to produce high-energy electrons, in order to avoid capillary wall damage, high power lasers need a tighter transverse confinement that cannot be achieved by the capillary discharge powered by Ohmic heating alone. The introduction of an additional laser for heating of the plasma leads to deeper and narrower plasma channels. Here we investigate the formation of laser-heated axially uniform plasma channels. Here, we show that a high degree of longitudinal uniformity can be achieved despite significant evolution of the heater laser during its propagation through the channel.
Radial density profile and stability of capillary discharge plasma waveguides of lengths up to 40 cm
We measured the parameter reproducibility and radial electron density profile of capillary discharge waveguides with diameters of 650 μm to 2 mm and lengths of 9 to 40 cm. To the best of the authors’ knowledge, 40 cm is the longest discharge capillary plasma waveguide to date. This length is important for ≥10 GeV electron energy gain in a single laser-driven plasma wakefield acceleration stage. Evaluation of waveguide parameter variations showed that their focusing strength was stable and reproducible to <0.2% and their average on-axis plasma electron density to <1%. These variations explain only a small fraction of laser-driven plasma wakefield acceleration electron bunch variations observed in experiments to date. Measurements of laser pulse centroid oscillations revealed that the radial channel profile rises faster than parabolic and is in excellent agreement with magnetohydrodynamic simulation results. We show that the effects of non-parabolic contributions on Gaussian pulse propagation were negligible when the pulse was approximately matched to the channel. However, they affected pulse propagation for a non-matched configuration in which the waveguide was used as a plasma telescope to change the focused laser pulse spot size.
Laser-heated capillary discharge waveguides as tunable structures for laser-plasma acceleration
Laser-heated capillary discharge waveguides are novel, low plasma density guiding structures able to guide intense laser pulses over many diffraction lengths and have recently enabled the acceleration of electrons to 7.8 GeV by using a laser-plasma accelerator (LPA). These devices represent an improvement over conventional capillary discharge waveguides, as the channel matched spot size and plasma density can be tuned independently of the capillary radius. This has allowed the guiding of petawatt-scale pulses focused to small spot sizes within large diameter capillaries, preventing laser damage of the capillary structure. High performance channel-guided LPAs require control of matched spot size and density, which experiments and simulations reported here show can be tuned over a wide range via initial discharge and laser parameters. In this paper, measurements of the matched spot size and plasma density in laser-heated capillary discharges are presented, which are found to be in excellent agreement with simulations performed using the MHD code MARPLE. Strategies for optimizing accelerator performance are identified based on these results.
Direct measurement of focusing fields in active plasma lenses
Not Available
On production and asymmetric focusing of flat electron beams using rectangular capillary discharge plasmas
A method for the asymmetric focusing of electron bunches, based on the active plasma lensing technique is proposed. Our method takes advantage of the strong inhomogeneous magnetic field generated inside the capillary discharge plasma to focus the ultrarelativistic electrons. The plasma and magnetic field parameters inside the capillary discharge are described theoretically and modeled with dissipative magnetohydrodynamic computer simulations enabling analysis of the capillaries of rectangle cross-sections. We could use large aspect ratio rectangular capillaries to transport electron beams with high emittance asymmetries, as well as assist in forming spatially flat electron bunches for final focusing before the interaction point.
Transport processes in plasma with an admixture of several heavy impurities
A two-temperature magnetohydrodynamic model of an ideal, fully ionized magnetized plasma consisting of electrons and several types of ions is developed for the case in which the mass of ions of the first type is much lower than that of jth-type ions, where j = 2,3,…, m{sub 1} ≪ m{sub j}, while the densities of heavy ions are so low that collisions between them can be neglected. The ion component is assigned a common velocity, common temperature, and common density, while its composition can vary in time and space.
Demonstration of a high repetition rate capillary discharge waveguide
A hydrogen-filled capillary discharge waveguide operating at kHz repetition rates is presented for parameters relevant to laser plasma acceleration (LPA). The discharge current pulse was optimized for erosion mitigation with laser guiding experiments and MHD simulation. Heat flow simulations and measurements showed modest temperature rise at the capillary wall due to the average heat load at kHz repetition rates with water-cooled capillaries, which is promising for applications of LPAs such as high average power radiation sources.
Active Plasma Lensing for Relativistic Laser-Plasma-Accelerated Electron Beams
The compact, tunable, radially symmetric focusing of electrons is critical to laser-plasma accelerator (LPA) applications. Experiments are presented demonstrating the use of a discharge-capillary active plasma lens to focus 100-MeV-level LPA beams. The lens can provide tunable field gradients in excess of 3000 T/m, enabling cm-scale focal lengths for GeV-level beam energies and allowing LPA-based electron beams and light sources to maintain their compact footprint. For a range of lens strengths, excellent agreement with simulation was obtained.
Laser-heater assisted plasma channel formation in capillary discharge waveguides
A method of creating plasma channels with controllable depth and transverse profile for the guiding of short, high power laser pulses for efficient electron acceleration is proposed. The plasma channel produced by the hydrogen-filled capillary discharge waveguide is modified by a ns-scale laser pulse, which heats the electrons near the capillary axis. This interaction creates a deeper plasma channel within the capillary discharge that evolves on a ns-time scale, allowing laser beams with smaller spot sizes than would otherwise be possible in the unmodified capillary discharge.