Experimental study of tail-span effects on a canard-controlled missile
Explore the source record for details and available documents.
Blair, A. B., Jr.↗
Engineering topics
Blair, A. B., Jr.
Publications and source records attributed to Blair, A. B., Jr..
Experimental study of tail-span effects on a generic canard-controlled missile
An experimental investigation was conducted on a cruciform canard controlled missile configuration to determine the effects of tail span/canard span ratio on controllability. The investigation was conducted over the Mach number range of 1.75 to 3.50. Reductions of tail span/canard span ratio produced lower static margins and higher trim angle of attack. The results show that canard controls can provide pitch- and yaw-control as well as roll-control by proper selection of the tail span/canard span ratio.
Blair, A. B., Jr.↗
Evaluation of a technique to generate artificially thickened boundary layers in supersonic and hypersonic flows
The feasibility of using a contoured honeycomb model to generate a thick boundary layer in high-speed, compressible flow was investigated. The contour of the honeycomb was tailored to selectively remove momentum in a minimum of streamwise distance to create an artificially thickened turbulent boundary layer. Three wind tunnel experiments were conducted to verify the concept. Results indicate that this technique is a viable concept, especially for high-speed inlet testing applications. In addition, the compactness of the honeycomb boundary layer simulator allows relatively easy integration into existing wind tunnel model hardware.
Porro, A. R.↗
Supersonic aerodynamic characteristics of monoplanar missiles with low-profile quadriform tails
Explore the source record for details and available documents.
Blair, A. B., Jr.↗
Supersonic aerodynamic characteristics of a maneuvering canard-controlled missile with fixed and free-rolling tail fins
Wind tunnel investigations were conducted on a generic cruciform canard-controlled missile configuration. The model featured fixed or free-rolling tail-fin afterbodies to provide an expanded aerodynamic data base with particular emphasis on alleviating large induced rolling moments and/or for providing canard roll control throughout the entire test angle-of-attack range. The tests were conducted in the NASA Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 to 3.50 at a constant Reynolds number per foot of 2.00 x 10 to the 6th. Selected test results are presented to show the effects of a fixed or free-rolling tail-fin afterbody on the static longitudinal and lateral-directional aerodynamic characteristics of a canard-controlled missile with pitch, yaw, and roll control at model roll angles of 0 deg and 45 deg.
Blair, A. B., Jr.↗
Supersonic aerodynamic characteristics of conformal carriage monoplanar circular missile configurations with low-profile quadriform tail fins
Wind tunnel tests were conducted on monoplanar circular missile configurations with low-profile quadriform tail fins to provide an aerodynamic data base to study and evaluate air-launched missile candidates for efficient conformal carriage on supersonic-cruise-type aircraft. The tests were conducted at Mach numbers from 1.70 to 2.86 for a constant Reynolds number per foot of 2,000,000. Selected test results are presented to show the effects of tail-fin dihedral angle, wing longitudinal and vertical location, and nose-body strakes on the static longitudinal and lateral-directional aerodynamic stability and control characteristics.
Blair, A. B., Jr.↗
Cavity door effects on aerodynamic loads of stores separating from cavities
Explore the source record for details and available documents.
Blair, A. B., Jr.↗
New test techniques to evaluate near field effects for supersonic store carriage and separation
Store separation and store carriage drag studies were conducted. A primary purpose is to develop new experimental methods to evaluate near field effects of store separation and levels of store carriage drag associated with a variety of carriage techniques for different store shapes and arrangements. Flow field measurements consisting of surface pressure distributions and vapor screen photographs are used to analyze the variations of the store separation characteristics with cavity geometry. Store carriage drag measurements representative of tangent, semi-submerged, and internal carriage installations are presented and discussed. Results are included from both fully metric models and models with only metric segments (metric pallets) and the relative merits of the two are discussed. Carriage drag measurements for store installations on an aircraft parent body are compared both with prediction methods and with installations on a generic parent body.
Sawyer, Wallace C.↗
Cavity door effects on aerodynamic loadings of compressed-carriage store configurations separating from cavities at supersonic speeds
An experimental wind-tunnel investigation has been conducted at supersonic Mach numbers to determine the effects of cavity doors on the aerodynamic characteristics of compressed-carriage store configurations during separation from a shallow box cavity (closed cavity flow) located in a simulated generic parent aircraft. The tests were conducted in the Langley Unitary Plan Wind Tunnel at free-stream Mach numbers of 1.70, 2.00, and 2.65 for a constant Reynolds number per foot of two million. Results are summarized to show the effects of cavity door opening angles, vertical door height, folded and unfolded tail fins, and Mach number on the near-field aerodynamic separation characteristics of a single missile-type store with in-line cruciform wings and tail fins.
Blair, A. B., Jr.↗
Supersonic axial-force characteristics of a rectangular-box cavity with various length-to-depth ratios in a flat plate
A wind-tunnel investigation has been conducted at Mach numbers of 1.50, 2.16, and 2.86 to obtain axial-force data on a metric rectangular-box cavity with various length-to-depth ratios. The model was tested at angles of attack from -4 deg to -2 deg. The results are summarized to show variations in cavity axial-force coefficient for deep- and shallow-cavity configurations with detached and attached cavity flow fields, respectively. The results of the investigation indicate that for a wide range of cavity lengths and depths, good correlations of the cavity axial-force coefficients (based on cavity rear-face area) are obtained when these coefficients are plotted as a function of cavity length-to-depth ratio. Abrupt increases in the cavity axial-force coefficients at an angle of attack of 0 deg. reflect the transition from an open (detached) cavity flow field to a closed (attached) cavity flow field. Cavity length-to-depth ratio is the dominant factor affecting the switching of the cavity flow field from one type to the other. The type of cavity flow field (open or closed) is not dependent on the test angles of attack except near the critical value of length-to-depth ratio.
Blair, A. B., Jr.↗
Wind-tunnel investigation at supersonic speeds of a remote-controlled canard missile with a free-rolling-tail brake torque system
Wind tunnel tests were conducted at Mach numbers 1.70, 2.16, and 2.86 to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed or free rolling tailfin afterbodies. Mechanical coupling effects of the free-rolling-tail afterbody were investigated by using an electronic electromagnetic brake system providing arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail roll rate. Remote-controlled canards were deflected to provide pitch, yaw, and roll control. Results indicate that the induced rolling moment coefficients due to canard yaw control are reduced and linearized for the free-rolling-tail (free-tail) configuration. The canards of the latter provide conventional roll control for the entire angle-of-attack test range. For the free-tail configuration, the induced rolling moment coefficient due to canard yaw control increased and the canard roll control decreased with increases in brake torque, which simulated bearing friction torque. It appears that a compromise in regard to bearing friction, for example, low-cost bearings with some friction, may allow satisfactory free-tail aerodynamic characteristics that include reductions in adverse rolling-moment coefficients and lower tail roll rates.
Blair, A. B., Jr.↗
Comprehensive missile aerodynamics programs for preliminary design
Previously cited in issue 12, p. 1851, Accession no. A82-27106
Dillenius, M. F. E.↗
Effect of tail-fin span on stability and control characteristics of a Canard-controlled missile at supersonic Mach numbers
An experimental wind-tunnel investigation was conducted at Mach numbers from 1.60 to 3.50 to obtain the longitudinal and lateral-directional aerodynamic characteristics of a circular, cruciform, canard-controlled missile with variations in tail-fin span. In addition, comparisons were made with the experimental aerodynamic characteristics using three missile aeroprediction programs: MISSILE1, MISSILE2, and NSWCDM. The results of the investigation indicate that for the test Mach number range, canard roll control at low angles of attack is feasible on tail-fin configurations with tail-to-canard span ratios of less than or equal to 0.75. The conards are effective pitch and yaw control devices on each tail-fin span configuration tested. Programs MISSILE1 and MISSILE2 provide very good predictions of longitudinal aerodynamic characteristics and fair predictions of lateral-directional aerodynamic characteristics at low angles of attack, with MISSILE2 predictions generally in better agreement with test data. Program NSWCDM provides good longitudinal and lateral-directional aerodynamic predictions that improve with increases in tail-tin span.
Blair, A. B., Jr.↗
Comprehensive missile aerodynamics programs for preliminary design
Two different classes of missile aeroprediction programs have been recently developed. The first class of programs provides rapid engineering predictions and includes MISSILE1 and MISSILE2 applicable to missile configurations with axisymmetric bodies. The second class of programs consists of the DEMON series, including a simplified version NSWCDM, designed to calculate detailed loadings acting on supersonic missiles which may have non-circular body cross sections. Both classes account for high angles of attack and track vortices from canard or wing section to the tail section. Extensive comparisons with experimental data are presented including nonlinear effects of canard control.
Dillenius, M. F. E.↗
Remote control canard missile with a free-rolling tail brake torque system
An experimental wind-tunnel investigation has been conducted at supersonic Mach numbers to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed and free-rolling tail-fin afterbodies. Mechanical coupling effects of the free-rolling tail afterbody were investigated using an electronic/electromagnetic brake system that provides arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail-roll rate. Results are summarized to show the effects of fixed and free-rolling tail-fin afterbodies that include simulated measured bearing friction torques on the longitudinal and lateral-directional aerodynamic characteristics.
Blair, A. B., Jr.↗
Effect of wing location and strakes on stability and control characteristics of a monoplanar circular missile with low-profile tail fins at supersonic speeds
A wind tunnel test was conducted at Mach numbers from 1.70 to 2.86 to extend the aerodynamic data base for wing tail effect on stability and control characteristics of monoplanar missiles. The results are summarized to show the effects of tail fin dihedral angle, wing location, and nose body strakes. The results indicate that an increase in tail fin dihedral angle produces positive increments in directional stability that allow greater trimmed lift coefficient values (maneuver potential) to be obtained. An increase in wing tail gap for the Mach number range reduces the aerodynamic center travel and produces reductions in directional stability at the lower angles of attack. A change in wing height (vertical location) strongly influences the angle of attack at which pitch up and the most directional stability occur. The addition of strakes to the baseline configuration increases directional stability, which allows a significant increase in stable trimmed maneuver capability. The tail fins of the baseline configuration are effective in producing roll and yaw control that are accompanied by favorable yaw and roll, respectively.
Blair, A. B., Jr.↗
An experimental wind-tunnel investigation of a ram-air-spoiler roll-control device on a forward-control missile at supersonic speeds
A parametric experimental wind-tunnel investigation was made at supersonic Mach numbers to provide design data on a ram-air-spoiler roll-control device that is to be used on forward-control cruciform missile configurations. The results indicate that the ram-air-spoiler tail fin is an effective roll-control device and that roll control is generally constant with vehicle attitude and Mach number unless direct canard and/or forebody shock impingement occurs. The addition of the ram-air-spoiler tail fins resulted in only small changes in aerodynamic-center location. For the ram-air-spoiler configuration tested, there are large axial force coefficient effects associated with the increased fin thickness and ram-air momentum loss.
Blair, A. B., Jr.↗
Wind-tunnel investigation at supersonic speeds of a canard-controlled missile with fixed and free-rolling tail fins
A wind tunnel investigation was made at free stream Mach numbers from 1.70 to 2.86 to determine the effects of fixed and free rolling tail fin afterbodies on the static longitudinal and lateral aerodynamic characteristics of a cruciform canard controlled missile model. The effect of small canard roll and yaw control deflections was also examined. The results indicate that the fixed and free rolling tail configurations have about the same lift curve slope and longitudinal stability level at low angles of attack. For the free rolling tail configuration, the canards provide conventional roll control with no roll control reversal at low angles of attack. The free rolling tail configuration reduced induced roll due to model roll angle and canard yaw control.
Blair, A. B., Jr.↗