Engineering Papers⌕ Search

Engineering topics

Blackwell, K. L.

Publications and source records attributed to Blackwell, K. L..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Space shuttle afterbody aerodynamics/plume simulation data summary

A series of parametric wind tunnel tests was conducted to provide a base for developing a simulation of afterbody/base aerodynamics for multibody/multibase rocket-powered vehicles (such as Space Shuttle) which use unheated air as the simulant gas in development wind tunnel tests. The tests described were parameterized on external configuration, nozzle internal configuration, base geometry, propulsion gas type, and freestream Mach number (0.5 to 3.5). The tests were conducted over a 4-year period. Presented in this report are the data and pertinent reference information necessary to perform an analysis which would lead to a simulation procedure. The type of data obtained during the tests described herein include model base afterbody, and nozzle internal surface static pressure distributions, model chamber pressure and temperature, and freestream conditions. Also included is a brief description of simulation procedures that were used by the Space Shuttle program.

Blackwell, K. L.↗
NASA NTRS1974

Effect of gaseous and solid simulated jet plumes on an 040A space shuttle launch configuration at m=1.6 to 2.2

The effect of plume-induced flow separation and aspiration effects due to operation of both orbiter and the solid rocket motors on a 0.019-scale model of the launch configuration of the Space Shuttle Vehicle is determined. Longitudinal and lateral-directional stability data were obtained at Mach numbers of 1.6, 2.0, and 2.2 with and without the engines operating. The plumes exiting from the engines were simulated by a cold-gas jet supplied by an auxiliary 200-atm air supply system and solid-body plume simulators. The aerodynamic effects produced by these two simulation procedures are compared. The parameters most significantly affected by the jet plumes are pitching moment, elevon control effectiveness, axial force, and orbiter wing loads. The solid rocket motor (SRM) plumes have the largest effect on the aerodynamic characteristics. The effect of the orbiter plumes in combination with the SRM plumes is also significant. Variations in the nozzle design parameters and configuration changes can reduce the jet plume-induced aerodynamic effects.

Dods, J. B., Jr.↗
NASA NTRS1973

Space shuttle (ATP configuration) abort staging investigation

A wind tunnel test conducted in a 14-inch trisonic wind tunnel to determine the force and moment characteristics of the ATP Orbiter and modified ATP External Tank/SRB combination during abort staging conditions is discussed. Six component aerodynamic force and moment data were recorded for the orbiter and ET/SRB combination. Pitch polars were obtained for an angle of attack range from minus 10 to plus 10 degrees and orbiter incidence angles (orbiter relative to the ET/SRB combination) of 0 and 2 degrees. A limited amount of yaw data were obtained at 0 degree angle of attack and beta range from minus 10 to plus 10 degrees. In addition, orbiter pitch control effectiveness was determined at several grid points. These force and moment data were obtained for Mach numbers of 0.9, 1.2 and 2.0.

Rampy, J. M.↗
NASA NTRS1973

Space shuttle: Pressure investigation of a space shuttle launch configuration consisting of a delta-wing orbiter and a swept-wing booster with canard and tip fans (M equals 0.6 to 1.3). Volume 1, part A: Booster data

Wind tunnel tests to determine the pressure distribution on a space shuttle launch configuration consisting of a delta wing orbiter and a swept wing booster with canard and tip fins were conducted. Pressure data were obtained for the combined orbiter and booster and for the booster alone at Mach numbers from 0.6 to 1.3, angles of attack from minus 8 degrees to plus 10 degrees, and sideslip angles from minus 6 degrees to plus 6 degrees. Pressure data were also obtained for the booster alone without canard at Mach numbers of 0.9 and 1.1. The pressure taps were distributed primarily over the booster upper surface and the orbiter lower surface.

Rampy, J. M.↗
NASA NTRS1972

Space shuttle: Static aerodynamic characteristics and control effectiveness of the GAC H-33 orbiter at Mach numbers from 0.6 to 4.96

A .003366 scale model of the Grumman H-33 orbiter was tested in the MSFC 14 inch Trisonic Wind Tunnel. Six-component aerodynamic force and moment data was recorded over a Mach number range of 0.6 to 4.96. Both pitch runs and yaw runs at various constant angles of attack were completed. The basic model configuration was investigated. The effects of a component build-up and of various control deflections were obtained. The elevons were deflected symmetrically and asymmetrically to determine elevator and aileron effectiveness. The rudder was tested both flared and unflared and the effects of deflections were determined in the flared case. The model was tested in pitch in two intervals. The first interval was from 0 to 20 deg. Then an adaptor was set to give the sting an offset angle and 20 to 40 deg angle of attack was obtained. Characteristics in sideslip were determined by varying sideslip angle from -4 deg to 10 deg with angle of attack set at 0 deg, 10 deg, 15 deg, and 30 deg.

Krepski, R.↗
NASA NTRS1972

Space shuttle abort separation pressure investigation. Volume 1, Part A: Booster data at Mach 5

Pressure data obtained from a joint Langley Research Center (LaRC)/Marshall Space Flight Center (MSFC) Space Shuttle about stage separation wind tunnel test are presented. The .00556 scale models of the McDonnell-Douglas orbiter and booster configurations were tested in proximity in Tunnel A of the Von Karman Facility (VKF), Arnold Engineering Development Center (AEDC). Mach numbers were 5.0, 3.0, and 2.0 and nominal Reynolds numbers were 1.09, 1.60, and 1.74 million per foot, respectively. Pressure data were obtained for the booster upper surface and orbiter lower surface at angles of attack of -10 deg, -5, 0, 5, and 10 deg for zero degrees sideslip. The models were tested at incidence angles of 0 and 5 deg for several separation distances and power conditions. Plug nozzles utilizing air were used to simulate booster and orbiter plumes at various altitudes along a nominal ascent trajectory. Powered conditions were 100, 50, and 0 percent of full power for the orbiter and 100, 50 and 0 percent of full power for the booster. Data were also obtained with the booster canard off in close proximity.

Trimmer, L. L.↗
NASA NTRS1972

Investigation of the McDonnell-Douglas orbiter and booster shuttle models in proximity at Mach numbers 2.0 to 6.0. Volume 7: Proximity data at Mach 4 and 6, interference free and launch vehicle data

Aerodynamic data obtained from a space shuttle abort stage separation wind tunnel test are presented. The .00556 scale models of the orbiter and booster configuration were tested in close proximity using dual balances during the time period of April 21 to April 27 1971. Data were obtained for both booster and orbiter over an angle of attack range from -10 to 10 deg for zero degree sideslip angle. The models were tested at several relative incidence angles and separation distances and power conditions. Plug nozzles utilizing air were used to simulate booster and orbiter plumes at various altitudes along a nominal ascent trajectory. Powered conditions were 100, 50, 25 and 0 percent of full power for the orbiter and 100, 50 and 0 percent of full power for the booster. Pitch control effectiveness data were obtained for both booster and orbiter with power on and off. In addition, launch vehicle data with and without booster power were obtained utilizing a single balance in the booster model. Data were also obtained with the booster canard off in close proximity and for the launch configuration.

Trimmer, L. L.↗
NASA NTRS1972

Abort separation of the shuttle

A sensitivity analysis of the factors which affect a successful abort maneuver following a space shuttle launching is presented. Wind tunnel tests were conducted using optimum simulation techniques and data acquisition procedures. Static stability, dynamic stability, and local loads were investigated. It is concluded that parallel abort separation of the space shuttle components is possible at both high and low dynamic pressures. Successful separation is dependent upon configuration, Mach number, rocket exhaust impingement and relative position and attitude of the stages.

Decker, J. P.↗