Engineering topics

Blackburn, John

Publications and source records attributed to Blackburn, John.

3 records

NASA NTRS1994

Active Inertial Vibration Isolators And Dampers

Report describes development of active inertial vibration isolators and dampers in which actuators electromagnet coils moving linearly within permanent magnetic fields in housings, somewhat as though massive, low-frequency voice coils in loudspeakers. Discusses principle of operation, electrical and mechanical considerations in design of actuators, characteristics of accelerometers, and frequency responses of control systems. Describes design and performance of one- and three-degree-of-freedom vibration-suppressing system based on concept.

Laughlin, Darren↗

NASA NTRS1992

Digital active material processing platform effort (DAMPER), SBIR phase 2

Applied Technology Associates, Inc., (ATA) has demonstrated that inertial actuation can be employed effectively in digital, active vibration isolation systems. Inertial actuation involves the use of momentum exchange to produce corrective forces which act directly on the payload being actively isolated. In a typical active vibration isolation system, accelerometers are used to measure the inertial motion of the payload. The signals from the accelerometers are then used to calculate the corrective forces required to counteract, or 'cancel out' the payload motion. Active vibration isolation is common technology, but the use of inertial actuation in such systems is novel, and is the focus of the DAMPER project. A May 1991 report was completed which documented the successful demonstration of inertial actuation, employed in the control of vibration in a single axis. In the 1 degree-of-freedom (1DOF) experiment a set of air bearing rails was used to suspend the payload, simulating a microgravity environment in a single horizontal axis. Digital Signal Processor (DSP) technology was used to calculate in real time, the control law between the accelerometer signals and the inertial actuators. The data obtained from this experiment verified that as much as 20 dB of rejection could be realized by this type of system. A discussion is included of recent tests performed in which vibrations were actively controlled in three axes simultaneously. In the three degree-of-freedom (3DOF) system, the air bearings were designed in such a way that the payload is free to rotate about the azimuth axis, as well as translate in the two horizontal directions. The actuator developed for the DAMPER project has applications beyond payload isolation, including structural damping and source vibration isolation. This report includes a brief discussion of these applications, as well as a commercialization plan for the actuator.

Blackburn, John↗

NASA NTRS1992

New inertial actuator provides isolation and stabilization in microgravity conditions

Experiments in materials and fluids processing have been conducted, or are planned, that take advantage of the low-g environment offered by space-based platforms. While the specific goals of the experiments vary, a common objective is to see improved results from the processes over those that would be obtained from similar ground-based experiments. While the space-based processing environment does offer a low-g environment, it is not disturbance free. Results of experiments already conducted, particularly those in manned vehicles, show that spacecraft induced disturbances still limit what can be achieved in materials processing. The duration of actual micro-g level environments is shorter than desired and periods of milli-g activity levels are not uncommon. While small scale experiments can be configured to overcome some of the vehicle disturbance sources, larger scale processing devices and commercial activities will require alternative methods to reduce the influences of spacecraft vibrations. Applied Technology Associates, Inc., (ATA), in cooperation with NASA Lewis Research Center, is developing hardware to provide a sustained micro-g experiment environment. This work is being sponsored under a Small Business Innovation Research (SBIR) program, which is currently in the Phase 2 development stage. ATA's approach is based on an inertial actuator, which when used as part of a closed-loop stabilization system, rejects unwanted disturbances to the experiment package. A prototype of the actuator has been fabricated and used in a laboratory demonstration to prove the principle of operation. ATA's presentation emphasized the development and testing of the Digital Materials Processing Experiment (DAMPER) inertial actuator. Physical and performance characteristics of the device are presented. Technical issues, including further optimization of the actuator's performance and plans for additional laboratory experiments, are also covered.

Blackburn, John↗