Engineering topics
Publications and source records attributed to Blackburn, Jeffrey L..
Correction for ‘Carbon dioxide and nitrogen reduction reactions using 2D transition metal dichalcogenide (TMDC) and carbide/nitride (MXene) catalysts’ by Zhaodong Li et al. , Energy Environ. Sci. , 2021, 14 , 6242–6286, DOI: 10.1039/D1EE03211A.
Abstract The authors investigate how chiral ligands attached to perovskite nanocrystal (PNC) surfaces structurally distort the perovskite lattice. Chiral electro‐optical properties of the resulting PNCs are demonstrated through the fabrication of a circularly polarized light (CPL) detector with a discrimination of up to 14% between left‐ and right‐handed CPL. Both experimental and electronic‐structure‐based simulations are combined to provide insights into the interactions (both structural and electronic) between chiral organic ligands and PNCs. The major finding is a centro‐asymmetric distortion of the surface lattice that penetrates up to five atomic unit cells deep into the PNCs, which is the likely cause of the chiral‐optical properties. Spin‐polarized transport through chiral‐PNCs results from the chiral‐induced spin selectivity effect and amplifies the discrimination between left and right‐handed CPL as is experimentally demonstrated in the detectors.
Not Available
Broad deployment of redox flow batteries is hindered, in part, due to the lack of highly selective ion-exchange membranes with high proton conductivity. We report a post-functionalization strategy for polybenzimidazole copolymer (PBI-co) membranes by a reacting mixture of concentrated sulfuric and phosphoric acids that led to improved membrane selectivity while retaining high proton conductivity. Fourier-transform infrared spectroscopy confirmed successful sulfonation and protonation of benzimidazole functionalities. PBI-co exhibits a very high room-temperature proton conductivity of 0.138 S cm -1 , as measured by electrochemical impedance spectroscopy. PBI-co also demonstrates electromigration crossover mitigation under applied current densities up to 500 mA cm -2 , and voltage pulses up to 1.4 V, while also inhibiting diffusion-driven vanadium crossover for over 20 days. Single-cell vanadium flow battery testing on post-functionalized PBI-co further confirms state-of-the-art battery performance with an ~99.5% Coulombic efficiency at 100 mA cm -2 and an area-specific resistance of ~20 mO cm 2 lower than Nafion-212 membrane.
We develop a better understanding of the many contributing factors that give rise to extreme optical anisotropy in 2D perovskites, and we then show that spin-coated films can exhibit excellent order comparable with exfoliated crystals.
Improving the carbon dioxide and nitrogen reduction reactions (CO 2 RR and NRR) can reduce anthropogenic greenhouse gas emissions while selectively producing chemicals needed for the fuel, plastic, and chemical industries. Efficient CO 2 RR can be used to replace fossil fuels as well as repurpose captured CO 2 , while new NRR pathways can be used to supplement or replace the energy intensive Haber–Bosch process for NH 3 generation with no CO 2 emissions. Therefore, this review article focuses on (photo)electrocatalytic and photocatalytic conversion of CO 2 and N 2 molecules into useful products, such as carbon monoxide, methanol, formic acid, and ammonia, using 2D transition metal dichalcogenides (TMDCs) and metal carbides/nitrides (MXenes). Additionally, these highly tunable 2D catalysts will be evaluated for their ability to selectively and efficiently undergo CO 2 RR and NRR by controlling defects, phases, edge sites, interfaces, and functional groups. We first address the CO 2 RR and NRR challenges, with a particular focus on theoretical mechanisms and minimum energy pathways. We follow this discussion with a detailed review of state-of-the-art 2D TMDC and MXene experimental catalysts for CO 2 RR and NRR (photo)electrocatalytic and photocatalytic reactions, and then address areas of opportunity for these catalytic reactions.
In this work, we review an emerging class of 2D layered metal-halide perovskites that exhibit important photophysical behavior involving inorganic exciton-to-molecular triplet energy flow. These novel systems have potential to impact several energy-related fields and processes, including optoelectronics, photon upconversion strategies, and triplet-based photocatalysis. Early studies provided initial guidance and revealed several intriguing questions that more recent developments, in terms of both expanded and diversified compositional tuning and more sophisticated characterization, have begun to answer. These questions center around the delicate interplay between physical and electronic structure that is perturbed by choice of perovskite structural motif and organic spacer properties. In addition to their distinct natures, the energy offsets between the metal-halide and molecular excitons can be leveraged for a variety of unique effects and emergent properties, including fast interlayer energy transfer. We review the key advances with an eye toward strategies for controlling photophysical outcomes based on structure-energy-function relationships.
Nature's biocatalytic processes are driven by photosynthesis, whereby photosystems I and II are connected in series for light-stimulated generation of fuel products or electricity. Externally supplying electricity directly to the photosynthetic electron transfer chain (PETC) has numerous potential benefits, although strategies for achieving this goal have remained elusive. Here we report an integrated photo-electrochemical architecture which shuttles electrons directly to PETC in living cyanobacteria. The cathode of this architecture electrochemically interfaces with cyanobacterial cells that have a lack of photosystem II activity and cannot perform photosynthesis independently. Illumination of the cathode channels electrons from an external circuit to intracellular PETC through photosystem I, ultimately fueling cyanobacterial conversion of CO 2 into acetate. We observed acetate formation when supplying both illumination and exogenous electrons under intermittent conditions (e.g., in a 30 s supply plus 30 min interval condition of both light and exogenous electrons). The energy conversion efficiency for acetate production under programmed intermittent LED illumination (400–700 nm) and exogenous electron supply reached ca. 9%, when taking into account the number of photons and electrons received by the biotic system, and ca. 3% for total photons and electrons supplied to the cyanobacteria. This approach is applicable for generating various CO 2 reduction products by using engineered cyanobacteria, one of which has enabled electrophototrophic production of ethylene, a broadly used hydrocarbon in the chemical industry. The resulting bio-electrochemical hybrid has the potential to produce fuel chemicals with numerous potential advantages over standalone natural and artificial photosynthetic approaches.
The rapid advancements in low-power portable/wearable electronic devices require concurrent development of technologies that can provide power without the need for bulky, heavy battery storage. Electronic ratchets, asymmetric transistor-based devices that can convert AC signals or electronic noise into DC power, have been proposed as one solution to this growing need. Here, the recent demonstration of conjugated polymer-based electronic ratchets offers a route toward lightweight, flexible power sources for portable applications. Here we demonstrate the fabrication of the first electronic ratchets where the active channel component consists of semiconducting single-walled carbon nanotubes (s-SWCNTs), which can transform electronic noise or AC signals to a stable DC current with higher output power (up to ca. 14 mW for a chemically doped device) than their polymer-based analogs. We also show that patterning of the dopant profile in the s-SWCNT channel enables reasonable power conversion performance (ca. 3.5 mW) with improved stability relative to homogeneously doped devices. Our findings demonstrate the promise for s-SWCNT electronic ratchets as energy harvesting devices for portable, low-power applications.
In this work, we demonstrate that the surface layers of single-crystal layered-2D Bi 2 Se 3 can be converted to layered-2D rhombohedral ß-In 2 Se 3 by annealing under a trimethylindium (TMIn) flux. Samples were prepared in a metalorganic chemical vapor deposition (MOCVD) chamber, then transferred under vacuum to a surface analysis chamber for analysis with low-energy electron diffraction (LEED) and Auger electron spectroscopy. Additional ex situ characterization included x-ray diffraction, transmission-electron microscopy (TEM), energy dispersive x-ray spectroscopy (EDS) elemental mapping, and Raman spectroscopy. The resulting single-crystal ß-In 2 Se 3 adopts the rhombohedral crystal structure (space group R-3m) and orientation of the underlying Bi 2 Se 3 , and the excess Bi atoms generated by this process create an underlying region of Bi-rich Bi x Se y . Due to the difference in bandgap between Bi 2 Se 3 and In 2 Se 3 , this conversion reaction presents a pathway to lateral heterojunctions if only selected regions are converted by masking the surface to spatially define the TMIn exposure. The conversion may also have implications for heteroepitaxy, because the in-plane lattice constants of Bi 2 Se 3 and In 2 Se 3 (0001) surfaces match those of InP and GaAs (111), respectively, and the natural cleavage planes of a layered-2D crystal facilitate substrate removal and reuse.
Asymmetry is an essential property to control. To do that in nanocrystalline systems we have developed methods to produce Janus-ligand shells on otherwise symmetric PbS quantum dots (QDs). In this work, we demonstrate that control by constructing a system that exhibits pyroelectricity built from spherical PbS QDs. We observed a pyroelectric current in two different configurations. In one configuration, the QDs are self-assembled into close-packed arrays while in the second configuration, the QDs are dispersed into an electro-inactive polymer, polydimethylsiloxane. Both exhibit a pyroelectric response. In the first configuration we estimate a lower limit of the pyroelectric coefficient to be 1.97 × 10 -7 C/m 2 K, which is likely limited by the degree of QD alignment during film formation but is already on par with common pyroelectric systems. Compared with inorganic ceramic-like and polymeric pyroelectric materials, pyroelectric films self-assembled from polar QDs are easier to prepare, responsive to light with different energies based on QD exciton energy, and the polarization of each QD could be easily tuned by constructing different Janus-ligand shells.
Heat is an abundant but often wasted source of energy. Thus, harvesting just a portion of this tremendous amount of energy holds significant promise for a more sustainable society. While traditional solid-state inorganic semiconductors have dominated the research stage on thermal-to-electrical energy conversion, carbon-based semiconductors have recently attracted a great deal of attention as potential thermoelectric materials for low-temperature energy harvesting, primarily driven by the high abundance of their atomic elements, ease of processing/manufacturing, and intrinsically low thermal conductivity. This quest for new materials has resulted in the discovery of several new kinds of thermoelectric materials and concepts capable of converting a heat flux into an electrical current by means of various types of particles transporting the electric charge: (i) electrons, (ii) ions, and (iii) redox molecules. This has contributed to expanding the applications envisaged for thermoelectric materials far beyond simple conversion of heat into electricity. This is the motivation behind this review. This work is divided in three sections. In the first section, we present the basic principle of the thermoelectric effects when the particles transporting the electric charge are electrons, ions, and redox molecules and describe the conceptual differences between the three thermodiffusion phenomena. In the second section, we review the efforts made on developing devices exploiting these three effects and give a thorough understanding of what limits their performance. In the third section, we review the state-of-the-art thermoelectric materials investigated so far and provide a comprehensive understanding of what limits charge and energy transport in each of these classes of materials.
Abstract Carbon laser‐patterning (CLaP) is emerging as a new tool for the precise and selective synthesis of functional carbon‐based materials for on‐chip applications. The aim of this work is to demonstrate the applicability of laser‐patterned nitrogen‐doped carbon (LP‐NC) for resistive gas‐sensing applications. Films of pre‐carbonized organic nanoparticles on polyethylenetherephthalate are carbonized with a CO 2 ‐laser. Upon laser‐irradiation a compositional and morphological gradient in the films is generated with a carbon content of 92% near the top surface. The specific surface areas of the LP‐NC are increased by introducing sodium iodide (NaI) as a porogen. Electronic conductivity and surface area measurements corroborate the deeper penetration of the laser‐energy into the film in the presence of NaI. Furthermore, impregnation of LP‐NC with MoC 1− x (<10 nm) nanoparticles is achieved by addition of ammonium heptamolybdate into the precursor film. The resulting doping‐sensitive nano‐grain boundaries between p‐type carbon and metallic MoC 1− x lead to an improvement of the volatile organic compounds sensing response of Δ R / R 0 = −3.7% or −0.8% for 1250 ppm acetone or 900 ppm toluene at room temperature, respectively, which is competitive with carbon‐based sensor materials. Further advances in sensitivity and in situ functionalization are expected to make CLaP a useful method for printing selective sensor arrays.
Single-walled carbon nanotubes (SWCNTs) are attractive materials for next-generation energy-harvesting technologies, including thermoelectric generators, due to their tunable opto-electronic properties and high charge carrier mobilities. Controlling the Fermi level within these unique 1D nanomaterials is often afforded by charge transfer interactions between SWCNTs and electron or hole accepting species. Conventional methods to dope SWCNT networks typically involve the diffusion of molecular redox dopant species into solid-state thin films, but solution-phase doping could potentially provide routes and/or benefits for charge carrier transport, scalability, and stability. Here, we develop a methodology for solution-phase doping of polymer-wrapped, highly enriched semiconducting SWCNTs using a p-type charge transfer dopant, F4TCNQ. This allows doped SWCNT inks to be cast into thin films without the need for additional post-deposition doping treatments. We demonstrate that the introduction of the dopant at varying stages of the SWCNT dispersion process impacts the ultimate thermoelectric performance and observe that the dopant alters the polymer selectivity for semiconducting vs metallic SWCNTs. In contrast to dense semiconducting polymer films, where solution-phase doping typically leads to disrupted morphologies and poorer TE performance than solid-state doping, thin films of solution-doped s-SWCNTs perform similarly to their solid-state doped counterparts. Interestingly, our results also suggest that solution-phase F4TCNQ doping leads to fully ionized and dimerized F4TCNQ anions in solid-state films that are not observed in films doped with F4TCNQ after deposition. Our results provide a framework for the application of solution-phase doping to a broad array of high-performance SWCNT-based thermoelectric materials and devices that may require high-throughput deposition techniques.
Naphthalene diimide based diammonium cations can be utilized to produce 1D organic/inorganic metal halide semiconductors with internal charge separation via charge transfer states that lie energetically below the metal-halide excitonic absorption.
Perovskite nanocrystals and SWCNTs join forces in optical synapses with attractive switching metrics and low-energy operation.
Two-dimensional transition metal dichalcogenides (2D-TMDCs) have gained attention for their promise in next-generation energy-harvesting and quantum computing technologies, but realizing these technologies requires a greater understanding of TMDC properties that influence their photophysics. To this end, we discuss here the interplay between TMDC microstructure and defects with the charge generation yield, lifetime, and mobility. As a model system, we compare monolayer-only and monolayer-rich MoS 2 grown by chemical vapor deposition, and we employ the TMDCs in Type-II charge-separating heterojunctions with semiconducting single-walled carbon nanotubes (s-SWCNTs). Our results suggest longer lifetimes and higher yields of mobile carriers in samples containing a small fraction of defect-rich multilayer islands on predominately monolayer MoS 2 . Compared to the monolayer-only heterojunctions, the carrier lifetimes increase from 0.73 μs to 4.71 μs, the hole transfer yield increases from 23% to 34%, and the electron transfer yield increases from 39% to 59%. We reach these conclusions using a unique combination of microwave photoconductivity (which probes only mobile carriers) along with transient absorption spectroscopy (which identifies spectral signatures unique to each material and type of photoexcited quasiparticle, but does not probe mobility). Overall, our results highlight the substantial changes in photophysics that can occur from small changes in TMDC microstructure and defect density, where the presence of defects does not necessarily preclude improvements in charge generation.
Not Available