Engineering Papers⌕ Search

Engineering topics

Bizon, P. T.

Publications and source records attributed to Bizon, P. T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Thermal-fatigue and oxidation resistance of cobalt-modified Udimet 700 alloy

Comparative thermal-fatigue and oxidation resistances of cobalt-modified wrought Udimet 700 alloy (obtained by reducing the cobalt level by direct substitution of nickel) were determined from fluidized-bed tests. Bed temperatures were 1010 and 288 C (1850 and 550 C) for the first 5500 symmetrical 6-min cycles. From cycle 5501 to the 14000-cycle limit of testing, the heating bed temperature was increased to 1050 C (1922 F). Cobalt levels between 0 and 17 wt% were studied in both the bare and NiCrAlY overlay coated conditions. A cobalt level of about 8 wt% gave the best thermal-fatigue life. The conventional alloy specification is for 18.5% cobalt, and hence, a factor of 2 in savings of cobalt could be achieved by using the modified alloy. After 13500 cycles, all bare cobalt-modified alloys lost 10 to 13 percent of their initial weight. Application of the NiCrAlY overlay coating resulted in weight losses of 1/20 to 1/100 of that of the corresponding bare alloy.

Bizon, P. T.↗
NASA NTRS1982

Thermal fatigue resistance of cobalt-modified UDIMET 700

The determination of comparative thermal fatigue resistances of five cobalt composition modifications of UDIMET 700 from fluidized bed tests is described. Cobalt compositional levels of 0.1, 4.3, 8.6, 12.8, 17.0 percent were being investigated in both the bare and coated (NiCrAlY overlay) conditions. Triplicate tests of each variation including duplicate tests of three control alloys are under investigation. Fluidized beds were maintained at 550 and 1850 F for the first 5500 cycles at which time the hot bed was increased to 1922 F. Immersion time in each bed is always 3 minutes. Upon the completion of 10,000 cycles, it appears that the 8.6 percent cobalt level gives the best thermal fatigue life. Considerable deformation of the test bars was observed.

Bizon, P. T.↗
NASA NTRS1981

Comparative thermal fatigue resistance of several oxide dispersion strengthened alloys

The thermal fatigue resistance of several oxide dispersion strengthened (ODS) alloys has been evaluated through cyclic exposure in fluidized beds. The ODS nickel-base alloy MA 754 and ODS iron-base alloy MA 956 as well as four experimental ODS Ni-16Cr-4.5Al base alloys with and without Ta additions were examined. Both bare and coated alloys were subjected to up to 6000 cycles where each cycle consisted of a 3 minute immersion in a fluidized bed at 1130 C followed by a 3 minute immersion in a bed at 357 C. Testing revealed that the thermal fatigue resistance of the ODS nickel-base alloys was excellent and about equal to that of directionally solidified superalloys. However, the thermal fatigue resistance of MA 956 was found to be poor. Metallographic examination of tested specimens revealed that, in general, the post-test microstructures can be rationalized on the basis of previous diffusion, mechanical property, and oxidation studies.

Whittenberger, J. D.↗
NASA NTRS1979

Noncontact strain measurement

Electro-optical extensometer containing optical and electronic components measures displacement in simulated turbine blade thermally cycled into and out of hot-gas stream. Innovation is useful in obtaining accurate strain histories for components subjected to severe thermal environments and other environmental changes.

Bizon, P. T.↗
NASA NTRS1979

Effect of grain orientation and coating on thermal fatigue resistance of a directionally solidified superalloy (MAR-M 247)

The effect of off-axis directionally solidified (DS) grain growth on thermal fatigue life of Mar-M 247 alloy was evaluated. Uncoated conventionally cast as well as DS wedge bars were cycled in a burner rig between 1070 C and room temperature. The longitudinal axis and leading edge of the specimen coincided. As the angle between the specimen longitudinal axis and growth axis increased, the thermal fatigue life decreased for both the uncoated and aluminide-coated bars. Life increases of about 50 cycles for the DS conditions were attributed to coating. The decrease in thermal fatigue life with increasing angle is primarily attributed to the increase in modulus of elasticity with increasing angle and not to the intersection of DS grain boundaries with the specimen leading edge. The thermal fatigue cracks were observed to be transgranular in the DS material. Limited tensile and stress-rupture properties of conventionally cast and off-axis DS Mar-M 247 alloy are also presented.

Bizon, P. T.↗
NASA NTRS1979

Three-dimensional finite-element elastic analysis of a thermally cycled single-edge wedge geometry specimen

An elastic stress analysis was performed on a wedge specimen (prismatic bar with single-wedge cross section) subjected to thermal cycles in fluidized beds. Seven different combinations consisting of three alloys (NASA TAZ-8A, 316 stainless steel, and A-286) and four thermal cycling conditions were analyzed. The analyses were performed as a joint effort of two laboratories using different models and computer programs (NASTRAN and ISO3DQ). Stress, strain, and temperature results are presented.

Bizon, P. T.↗
NASA NTRS1978

Experimental determination of transient strain in a thermally-cycled simulated turbine blade utilizing a non-contact technique

A type of noncontacting electro-optical extensometer was used to measure the displacement between parallel targets mounted on the leading edge of a simulated turbine blade throughout a complete heating and cooling cycle. The blade was cyclically heated and cooled by moving it into and out of a Mach 1 hot gas stream. The principle of operation and measurement procedure of the electro-optics extensometer are described.

Calfo, F. D.↗
NASA NTRS1977

Effect of heating method on stress-rupture life

The effect of radiant(furnace), resistance(electric current), burner(hot gas stream), and a combination of resistance and burner heating on intermediate time (100 to 300 hr) stress-rupture life and reduction of area was evaluated. All heating methods were studied using the nickel-based alloy Udimet 700 while all but burner heating were evaluated with the cobalt-based alloy Mar-M 509. Limited test results of eight other superalloys were also included in this study. Resistance heated specimens had about 20 to 30 percent of the stress-rupture life of radiant heated specimens. The limited burner heating data showed about a 50 percent life reduction as compared to the radiant heated tests. A metallurgical examination gave no explanation for these reductions.

Bizon, P. T.↗
NASA NTRS1976

Thermal fatigue-and-oxidation-resistant alloy

Cast nickel-base alloy designated as NASA TAZ-8A has been developed for use in high temperature aircraft engine components. TAZ-8A composition is 8Ta, 6Cr, 6A1, 4Mo, 4W, 2Cb, 0.5Zr, 0.125C, 0.004B, and balance Ni (weight percent). Its specific gravity at room temperature is 8.65.

Bizon, P. T.↗
NASA NTRS1976

Comparative thermal fatigue resistance

Nineteen cast nickel-base alloys, five cast cobalt-base alloys, and two wrought nickel-base alloys are included in study. Five nickel-base alloys have directionally-solidified polycrystalline grain structure. Three diffusion coatings and vapor-deposited overlay coating are also included in investigation.

Bizon, P. T.↗
NASA NTRS1976

Thermal-stress fatigue behavior of twenty-six superalloys

The comparative thermal-stress fatigue resistances of 26 nickeland cobalt-base alloys were determined by fluidized bed tests. Cycles to cracking differed by almost three orders of magnitude for these materials, with directional solidification and surface protection showing definite benefit. The alloy-coating combination with the highest thermal-stress fatigue resistance was directionally solidified NASA TAZ-8A with an RT-SP coating. Its oxidation resistance was also excellent, showing approximately a 1/2 percent weight loss after 14,000 fluidized bed cycles.

Bizon, P. T.↗
NASA NTRS1975

Comparative thermal fatigue resistances of twenty-six nickel and cobalt base alloys

Thermal fatigue resistances were determined from fluidized bed tests. Cycles to cracking differed by almost three orders of magnitude for these materials with directional solidification and surface protection of definite benefit. The alloy-coating combination with the highest thermal fatigue resistance was directionally solidified NASA TAZ-8A with an RT-XP coating. It oxidation resistance was excellent, showing almost no weight change after 15 000 fluidized bed cycles.

Bizon, P. T.↗
NASA NTRS1975

Thermal fatigue resistance of NASA WAZ-20 alloy with three commercial coatings

Screening tests using three commercial coatings (Jocoat, HI-15, and RT-1A) on the nickel-base alloy NASA WAZ-20 were performed by cyclic exposure in a Mach 1 burner facility. These tests showed Jocoated WAZ-20 to have the best cracking resistance. The thermal fatigue resistance of Jocoated WAZ-20 in both the random polycrystalline and directionally solidified polycrystalline forms relative to that of other superalloys was then evaluated in a fluidized-bed facility. This investigation showed that Jocoated random polycrystalline WAZ-20 ranked approximately in midrange in thermal fatigue life. The thermal fatigue life of directionally solidified Jocoated WAZ-20 was shorter than that of other directionally solidified alloys but still longer than that of all alloys in the random polycrystalline form.

Bizon, P. T.↗