Engineering Papers⌕ Search

Engineering topics

Biermann, David

Publications and source records attributed to Biermann, David.

26 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1938

The Aerodynamic Characteristics of Four Full-Scale Propellers Having Different Plan Forms

Tests were made of four propellers, with diameters of 10 feet, having different blade plan forms. One propeller (Navy design no. 5868-r6) was of the usual present-day type and was used as a basis of comparison for the other three, which had unusual plan forms distinguished by the inward (toward the hub) location of the sections having the greatest blade width. It was found that propellers with points of maximum blade width occurring closer to the hub than on the present-day type of blade had higher peak efficiencies but lower take-off efficiencies. This results was found true for a "clean" liquid-cooled engine installation. It appears that some modification could be made to present plan forms which would produce propellers having more satisfactory aerodynamic qualities. The propellers with the inward location of the points of maximum blade width had lower thrust and power coefficients and stalled earlier than the present-day type.

Hartman, Edwin P↗
NASA NTRS1938

Tests of Five Full-Scale Propellers in the Presence of a Radial and a Liquid-Cooled Engine Nacelle, Including Tests of Two Spinners

Wind-tunnel tests are reported of five 3-blade 10-foot propellers operating in front of a radial and a liquid-cooled engine nacelle. The range of blade angles investigated extended from 15 degrees to 45 degrees. Two spinners were tested in conjunction with the liquid-cooled engine nacelle. Comparisons are made between propellers having different blade-shank shapes, blades of different thickness, and different airfoil sections. The results show that propellers operating in front of the liquid-cooled engine nacelle had higher take-off efficiencies than when operating in front of the radial engine nacelle; the peak efficiency was higher only when spinners were employed. One spinner increased the propulsive efficiency of the liquid-cooled unit 6 percent for the highest blade-angle setting investigated and less for lower blade angles. The propeller having airfoil sections extending into the hub was superior to one having round blade shanks. The thick propeller having a Clark y section had a higher take-off efficiency than the thinner one, but its maximum efficiency was possibly lower. Of the three blade sections tested, Clark y, R.A.F. 6, and NACA 2400-34, the Clark y was superior for the high-speed condition, but the R.A.F. 6 excelled for the take-off condition.

Biermann, David↗
NASA NTRS1937

A study of the factors affecting the range of airplanes

A study was made of the most important factors affecting the range of airplanes. Numerical examples are given showing the effects of different variables on the range of a two-engine airplane. The takeoff problems of long-range airplanes are analyzed.

Biermann, David↗
NASA NTRS1936

Relative Efficiencies and Design Charts for Various Engine-Propeller Combinations, Special Report

The relative efficiencies of various engine-propeller combinations were the subject of a study that covered the important flight conditions, particularly the take-off. Design charts that graphically correlate the various propeller parameters were prepared to facilitate the solution of problems and also to c1arify the conception of the relationships of the various engine-propeller design factors. It is shown that, among the many methods for improving the take-off thrust, the use of high-pitch, large-diameter controllable propellers turning at low rotational speeds is probably the most generally promising. With such a combination the take-off thrust may be further increased, at the expense of a small loss in cruising efficiency, by compromise designs wherein the pitch setting is slightly reduced and the diameter is further increased. The degree of compromise necessary to accomplish the maximum possible take-off improvement depends on such design factors as overspeeding and overboosting at take-off as well as depending on the design altitude. Both overspeeding and designing for altitude operation have the same effect on the take-off thrust as compromising in that the propulsive efficiency is increased thereby; boosting the engine, however, has the reverse effect on the propulsive efficiency, although the brake horsepower is increased.

Biermann, David↗
NASA NTRS1936

The Drag of Airplane Wheels, Wheel Fairings, and Landing Gears - III

The tests reported in this report conclude the investigation of landing-gear drag that has been carried out in the NACA 20-foot wind tunnel. They supplement earlier tests (reported in Technical Report No. 485) made with full-scale dummy wheels, wheel fairings, and landing gears intended for airplanes of 3,000 pounds gross weight and include tests of tail wheels and tail skids.

Herrnstein, William H , Jr↗
NASA NTRS1935

The Drag of Airplane Wheels, Wheel Fairings, and Landing Gears - I

This report presents the results of tests made in the 7-by 10-foot wind tunnel and in the 20-foot tunnel of the National Advisory Committee for Aeronautics to determine the drag of a number of airplane wheels, wheel fairings, and landing gears designed or selected for an airplane of 3,000 pounds gross weight. All tests were made on full-size models; those in the 7-by 10-foot tunnel were made at air speeds up to 80 miles per hour and those in the 20-foot tunnel were made at air speeds up to 100 miles per hour. Although most of the landing-gear tests were made in conjunction with a fuselage and at 0 degree pitch angle, some of the tests were made in conjunction with fuselage plus wings and a radial air-cooled engine and at pitch angles from -5 degrees to 6 degrees to obtain an indication of the general effect of these various items on landing-gear drag. All tests were made in the absence of propeller slipstream.

Herrnstein, William H↗
NASA NTRS1934

The Interference Between Struts in Various Combinations

This report presents the results of wind tunnel tests made to determine the interference drag arising from various arrangements of streamline struts and round struts, or cylinders. Determinations were made of the interference drag of struts spaced side by side, struts in tandem, tandem struts encased in a single fairing, a strut intersecting a plane, and struts intersecting to form a v. Three sizes of struts were used for most of the tests. These tests show that the interference drag arising from struts in close proximity may be of considerable magnitude, in some instances amounting to more than the drag of the struts themselves.

Biermann, David↗