Engineering Papers⌕ Search

Engineering topics

Biener, Juergen

Publications and source records attributed to Biener, Juergen.

At least 19 records

3D Printed Nanoporous Separators Based on Polymerization-Induced Phase Separation for Fast-Charging, High Cycling Stability Li-Ion Batteries

Fast charging and stable lithium-ion batteries (LIBs) require prompt Li ion transport between electrodes. 3D porous separators can potentially improve ion transport at both the microscale and macroscale levels. Additive manufacturing (AM) is an ideal tool to produce and study 3D porous separators of LIBs, although little work has been reported in this area. Here, we demonstrate porous structural control in layer-by-layer printed hexanediol diacrylate (HDDA) separators using a projection micro stereolithography (PμSL) AM technology and present their corresponding battery performance in lithium nickel manganese cobalt oxide (NMC)/graphite full cells. The composition of photocurable resin determines the porous morphology (e.g., bicontinuous and droplet-like), while the settings of printing layer thickness and number of exposures can be used to adjust the porosity (e.g., from 27% to 63%). Optimal resin and print conditions are determined, and the resulting separator exhibits superior Li ion conductivity and therefore higher rate performance and longer cycling life. Compared with a Celgard 2325 separator, the optimized porous HDDA separator increases the 10C-rate capacity by 34% and decreases the capacity degradation rate at the 1C-rate by 4.9%. In conclusion, this work paves the way for future AM of 3D separators for high-energy, high-power, and long-cycling-life LIBs.

25 ENERGY STORAGE↗

Cu Based Dilute Alloys for Tuning the C 2+ Selectivity of Electrochemical CO 2 Reduction

Electrochemical CO 2 reduction is a promising technology for replacing fossil fuel feedstocks in the chemical industry but further improvements in catalyst selectivity need to be made. So far, only copper-based catalysts have shown efficient conversion of CO 2 into the desired multi-carbon (C 2+ ) products. This work explores Cu-based dilute alloys to systematically tune the energy landscape of CO 2 electrolysis toward C 2+ products. Selection of the dilute alloy components is guided by grand canonical density functional theory simulations using the calculated binding energies of the reaction intermediates CO*, CHO*, and OCCO* dimer as descriptors for the selectivity toward C 2+ products. Here, a physical vapor deposition catalyst testing platform is employed to isolate the effect of alloy composition on the C 2+ /C 1 product branching ratio without interference from catalyst morphology or catalyst integration. Six dilute alloy catalysts are prepared and tested with respect to their C 2+ /C 1 product ratio using different electrolyzer environments including selected tests in a 100-cm 2 electrolyzer. Consistent with theory, CuAl, CuB, CuGa and especially CuSc show increased selectivity toward C 2+ products by making CO dimerization energetically more favorable on the dominant Cu facets, demonstrating the power of using the dilute alloy approach to tune the selectivity of CO 2 electrolysis.

36 MATERIALS SCIENCE↗

Refractive index matching base resin for extremely fine three-dimensional ceramic structures

An optically clear resin for additive manufacturing includes an optically clear ceramic precursor having a pre-defined refractive index. Each molecule of the ceramic precursor has at least two photopolymerizable functional groups, at least one of the photopolymerizable functional groups being functionalized with a refractive index-tuning group thereby causing the ceramic precursor to have the pre-defined refractive index.

Mettry, Magi↗

Dilute alloy catalysts for electrochemical CO 2 reduction

A product includes a dilute alloy catalyst for carbon dioxide reduction. The catalyst has a majority component and at least one minority component. The majority component is present in a concentration of greater than 90 atomic percent of the catalyst. The majority component is copper, and each minority component is selected from the group consisting of: a transition metal, a main group metal, a lanthanide, and a semimetal. A method includes forming a product on a cathode. The product includes a dilute alloy catalyst for carbon dioxide reduction. The catalyst has a majority component and at least one minority component. The majority component is present in a concentration of greater than 90 atomic percent of the catalyst. The majority component is copper, and each minority component is selected from the group consisting of: a transition metal, a main group metal, a lanthanide, and a semimetal.

Biener, Juergen↗

Highly active thermally stable nanoporous gold catalyst

In one embodiment, a product includes a nanoporous gold structure comprising a plurality of ligaments, and a plurality of oxide particles deposited on the nanoporous gold structure; the oxide particles are characterized by a crystalline phase.

Biener, Juergen↗

Actuation via surface chemistry induced surface stress

A method of controlling macroscopic strain of a porous structure includes contacting a porous structure with a modifying agent which chemically adsorbs to a surface of the porous structure and modifies an existing surface stress of the porous structure. Additional methods and systems are also presented.

Biener, Juergen↗

Tailoring of pores in aerogels using 3D printed structures

In one embodiment, a method includes acquiring a three-dimensional printed template created using an additive manufacturing technique, infilling the template with an aerogel precursor solution, allowing formation of a sol-gel, and converting the sol-gel to an aerogel. In another embodiment, a product includes an aerogel having inner channels corresponding to outer walls of a three-dimensional printed template around which the aerogel was formed.

Chandrasekaran, Swetha↗

Flow-through reactor for electrocatalytic reactions

A flow-through electrolysis cell includes a hierarchical nanoporous metal cathode. A method of reducing CO 2 includes flowing the CO 2 through the hierarchical nanoporous metal cathode of the flow-through electrolysis cell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Boosting the H 2 –D 2 Exchange Activity of Dilute Nanoporous Ti–Cu Catalysts through Oxidation–Reduction Cycle–Induced Restructuring

The use of nanoporous metals as catalysts has attracted significant interest in recent years. Their high-curvature, nanoscale ligaments provide not only high surface area but also a high density of undercoordinated step edge and kink sites. However, their long-term stability, especially at higher temperatures, is often limited by thermal coarsening and the associated loss of surface area. Herein, it is demonstrated that the nanoscale morphology of nanoporous Cu can be regenerated by applying oxidation/reduction cycles at 250 °C. Specifically, the morphological evolution and H 2 dissociation activity of hierarchical nanoporous Cu catalysts doped with Ti during structural rearrangement triggered by oxidative and reductive atmospheres at elevated temperatures are studied. In addition to coarsening of the structure at elevated temperatures, oxidation at 400 °C causes an expansion of the ligaments. Further, subsequent reduction at 400 °C leads to the formation of particles and a drop in the H 2 dissociation activity compared the fresh catalyst. However, performing the redox cycle at 250 °C reverses coarsening and boosts the H 2 dissociation activity for the hydrogen–deuterium (H 2 –D 2 ) reaction. Herein, the possibility to reverse coarsening is demonstrated, thereby mitigating the loss of activity frequently observed in nanoporous catalysts.

36 MATERIALS SCIENCE↗

Tungsten doped diamond shells for record neutron yield inertial confinement fusion experiments at the National Ignition Facility

We report on fabrication and characterization of layered, tungsten doped, spherical about 2 mm diameter microcrystalline diamond ablator shells for inertial confinement fusion (ICF) experiments at the National Ignition Facility. As previously reported, diamond ICF ablator shells can be fabricated by chemical vapor deposition (CVD) on solid spherical silicon mandrels using an ellipsoidal microwave plasma reactor. In the present work, we further developed these ablator shells by embedding a W -doped diamond layer sandwiched between two undoped diamond regions. W incorporation in diamond was achieved by adding tungsten hexacarbonyl to the CH 4 /H 2 CVD feed gas. We observe that the W doping concentration decreases with increasing deposition rate which, in turn, is controlled by adjusting the total gas pressure. Cross sectional microstructural analysis reveals sharp interfaces between doped and undoped regions of the diamond shell and uniform W distribution with concentrations up to about 0.3 at.%. At higher W concentrations (>0.3 at.%) formation of tungsten carbide precipitates is observed. Using a 3-shock 1.6 MJ laser pulse, the targets described in this work produced the first laser driven implosion to break the 1 × 10 16 neutron yield barrier, followed by experiments (described in future publications) with similar targets and slightly more laser energy producing yields as high as 4 × 10 17 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of Gold Catalyst Surface Morphology on Wetting Behavior and Electrochemical CO 2 Reduction Performance in a Large-Area Zero-Gap Gas Diffusion Electrolyzer

We report catalyst surface area and wetting behavior are key factors in determining the performance of gas diffusion electrode (GDE) electrolyzers for electrochemical CO 2 reduction. In this work, we report the integration of sub-1 μm thick nanoporous gold (npAu) catalyst coatings into a large-area (25 cm 2 ) zero-gap electrolyzer. The npAu coatings were prepared by magnetron sputtering (MS) of thin AgAu alloy films on the microporous carbon layer of a gas diffusion layer (GDL) followed by Ag leaching. Compared to MS Au films of the same thickness, npAu catalyst coatings enable higher Faradaic efficiencies and improved catalyst stability for CO 2 -to-CO reduction with Faradaic efficiencies of up to 88% at 100 mA/cm 2 . For a 800 nm npAu coating, the device level energy efficiency for CO 2 to CO conversion reaches 45% (52% for CO + H 2 ) at 100 mA/cm 2 with a single pass CO 2 conversion efficiency of ~12%. Contact angle measurements reveal that npAu coatings provide a more hydrophobic electrode interface compared to MS Au coatings, suggesting that the more hydrophobic interfacial environment of npAu coatings helps mitigating electrode flooding which is associated with performance deterioration over time.

30 DIRECT ENERGY CONVERSION↗

Facilitating Hydrogen Dissociation over Dilute Nanoporous Ti–Cu Catalysts

The dissociation of H 2 is an essential elementary step in many industrial chemical transformations, typically requiring precious metals. Here, we report a hierarchical nanoporous Cu catalyst doped with small amounts of Ti (npTiCu) that increases the rate of H 2 –D 2 exchange by approximately one order of magnitude compared to the undoped nanoporous Cu (npCu) catalyst. The promotional effect of Ti was measured via steady-state H 2 –D 2 exchange reaction experiments under atmospheric pressure flow conditions in the temperature range of 300–573 K. Pretreatment with flowing H 2 is required for stable catalytic performance, and two temperatures, 523 and 673 K, were investigated. The experimentally determined H 2 –D 2 exchange rate is 5–7 times greater for npTiCu vs the undoped Cu material under optimized pretreatment and reaction temperatures. The H 2 pretreatment leads to full reduction of Cu oxide and partial reduction of surface Ti oxide species present in the as-prepared catalyst as demonstrated using in situ ambient pressure X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. The apparent activation energies and pre-exponential factors measured for H 2 –D 2 exchange are substantially different for Ti-doped vs undoped npCu catalysts. Density functional theory calculations suggest that isolated, metallic Ti atoms on the surface of the Cu host can act as the active surface sites for hydrogen recombination. Furthermore, the increase in the rate of exchange above that of pure Cu is caused primarily by a shift in the rate-determining step from dissociative adsorption on Cu to H/D atom recombination on Ti-doped Cu, with the corresponding decrease in activation entropy that it produces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Systems and methods for electrical energy storage

The present disclosure relates to an electrical energy storage apparatus which forms an interpenetrating, three dimensional structure. The structure may have a first non-planar channel filled with an anode material to form an anode, and a second non-planar channel adjacent the first non-planar channel filled with a cathode material to form a cathode. A third non-planar channel may be formed adjacent the first and second non-planar channels and filled with an electrolyte. The first, second and third channels are formed so as to be interpenetrating and form a spatially dense, three dimensional structure. A first current collector is in communication with the first non-planar channel and forms a first electrode, while a second current collector is in communication with the second non-planar channel and forms a second electrode. A separator layers separates the current collectors.

Duoss, Eric B.↗

Dilute Alloys Based on Au, Ag, or Cu for Efficient Catalysis: From Synthesis to Active Sites

The development of new catalyst materials for energy-efficient chemical synthesis is critical as over 80% of industrial processes rely on catalysts, with many of the most energy-intensive processes specifically using heterogeneous catalysis. Catalytic performance is a complex interplay of phenomena involving temperature, pressure, gas composition, surface composition and structure over multiple length and time scales. In response to this complexity, the integrated approach to heterogeneous dilute-alloy catalysis reviewed here brings together materials synthesis, mechanistic surface chemistry, reaction kinetics, in-situ and operando characterization, and theoretical calculations in a coordinated effort to develop design principles to predict and improve catalytic selectivity. Dilute alloy catalysts—in which isolated atoms or small ensembles of the minority metal on the host metal lead to enhanced reactivity while retaining selectivity—are particularly promising as selective catalysts. Several dilute alloy materials using Au, Ag and Cu as the majority host element, including more recently introduced support-free nanoporous metals and oxide-supported nanoparticle "raspberry colloid templated (RCT)" materials, are reviewed for selective oxidation and hydrogenation reactions. Progress in understanding how such dilute alloy catalysts can be used to enhance selectivity of key synthetic reactions is reviewed, including quantitative scaling from model studies to catalytic conditions. The dynamic evolution of catalyst structure and composition studied in surface science and catalytic conditions and their relationship to catalytic function are also discussed, followed by advanced characterization and theoretical modeling that have been developed to determine the distribution of minority metal atoms at or near the surface. Furthermore, the integrated approach demonstrates the success of bridging the divide between fundamental knowledge and design of catalytic processes in complex catalytic systems, which can accelerate the development of new and efficient catalytic processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO 2 Reduction Using Physical Vapor Deposition Methods

Electrochemical CO 2 reduction (ECR) promises the replacement of fossil fuels as the source of feedstock chemicals and seasonal storage of renewable energy. While much progress has been made in catalyst development and electrochemical reactor design, few studies have addressed the effect of catalyst integration on device performance. Using a microfluidic gas diffusion electrolyzer, we systematically studied the effect of thickness and the morphology of electron beam (EB) and magnetron-sputtered (MS) Cu catalyst coatings on ECR performance. We observed that EB-Cu outperforms MS-Cu in current density, selectivity, and energy efficiency, with 400 nm thick catalyst coatings performing the best. Additionally, the superior performance of EB-Cu catalysts is assigned to their faceted surface morphology and sharper Cu/gas diffusion layer interface, which increases their hydrophobicity. Tests in a large-scale zero-gap electrolyzer yielded similar product selectivity distributions with an ethylene Faradaic efficiency of 39% at 200 mA/cm 2 , demonstrating the scalability for industrial ECR applications.

36 MATERIALS SCIENCE↗

System Integration of Rationally Designed Dilute Alloy Catalysts for Energy-Efficient Electrochemical CO 2 -To-Fuel Conversion

Energy effiecient electrochemical conversion of CO 2 to high-demand chemicals and transportation fuels using renewable solar and wind energy is a key technology needed for a high-productivity, low-carbon future. However, the development of scalable, low-cost, active, selective, and stable electrocatalysts remains a key challenge that needs to be overcome to enable high-volume conversion of CO 2 to feedstock chemicals for the chemical industry. In previous work, Lawrence Livermore National Laboratory (LLNL) has developed a rational design platform for dilute alloy transition metal electrocatalysts that promise to make electrochemical CO 2 conversion more energy efficient and selective. In this project, we worked with our industrial partners, Twelve and TotalEnergies, to improve scale up, integration, and stability of LLNL’s dilute alloy catalyst technology into an industry-relevant zero gap electrolyzer platform. Through virtual experiments and data analysis, we designed efficient and cost-effective copper-based catalysts. The catalyst was specifically designed to streamline the slowest and most energy-intensive step of the electrochemical chemical transformation of CO 2 to multi-carbon products – that is making the carbon-carbon bond by dimerization of the reaction intermediate carbon monoxide - resulting in up to 10% improvement in energy efficiency for C 2 products while simultaneously increasing the selectivity towards C 2 products. We tested two different scalable catalyst coating technologies and down-selected magnetron sputtering as the technique that provided the best control over catalyst loading, composition, and morphology. Using this technology, we successfully demonstrated integration of our dilute alloy catalysts into a 100 cm 2 electrolyzer platform with Faradaic efficiencies for ethylene production reaching 40% at a current density of 200 mA/cm 2 . We also developed the technology to integrate a well-defined nanoscale porosity by depositing alloy compositions that were compatible with dealloying, that is, selective leaching of an alloy component to generate nanoscale porosity. We observed that integration of the dealloying-derived nanoporosity improved catalyst performance and stability by leading to a more hydrophobic catalyst/anion exchange membrane interface. Unsolved problems that still need to be addressed are corrosion of the Cu catalyst -specifically if the used catalyst is exposed to air - as well as long term stability do to salt formation/deposition and flooding of the catalyst/electrolyzer flow channels, especially at higher current densities. As we only worked on optimization of catalyst composition, coating thickness, and morphology, further performance optimization will require a system level approach that includes optimization of electrolyzer design and membrane technology.

36 MATERIALS SCIENCE↗