Engineering Papers⌕ Search

Engineering topics

Bhattacharya, S.

Publications and source records attributed to Bhattacharya, S..

At least 37 records · Page 2

Effectiveness of the metal coating on U–7Mo dispersion fuel in Al during irradiation

The effectiveness of a transition metal coating layer as a diffusion barrier between the UMo and matrix Al was examined. The samples were cut from KAERI-made U-Mo/Al dispersion miniplates containing 8 gU/cm 3 fuel meat. Mo, W and Zr were included as coating candidates. A physical vapor deposition (PVD) method was used to produce about a 0.2-mu m thick coating layer on the UMo. An Al protection coating layer was subsequently applied to protect the main coating layer. The samples were irradiated at the ATLAS facility in Argonne National laboratory with 84-MeV Xe 26+ ions, with the beam current of 200 particles nano ampere (pnA), to achieve a final dose of 2.7x10 17 ions/cm 2 . Post-irradiation examinations included focused ion beam (FIB), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Furthermore, among the coating metals, Mo showed the highest survival during the fuel plate fabrication and endurance during irradiation, which was consistent with the pre-irradiation thermodynamics evaluation. This result also emphasized the importance of the Al protection layer.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Al 2 O 3 coating on fretting wear performance of Zr alloy

Fretting wear caused by flow-induced vibration (FIV) is one of the predominant tribological failure modes in nuclear power plants and industry. This paper presents an experimental study of the effect on fretting performance of alumina (Al 2 O 3 ) coatings produced by atomic layer deposition (ALD) on Zirlo (a Zr alloy), a common nuclear fuel cladding alloy. A coating with uniform thickness of about 750 nm was deposited onto a Zirlo flat. Because the typical thickness of fuel cladding is 1 mm, an ultra-thin coating is required. The hardness and elastic modulus of the ALD coating were measured by nano-indentation techniques. With a pin-on-flat contact configuration in low-amplitude reciprocating contact, fretting performance was measured for uncoated Zirlo, Al2O 3 -coated Zirlo, and Al 2 O 3 -coated Zirlo followed by heat treatment. Results showed that the as-deposited Al 2 O 3 coating provided slight improvement in fretting wear performance. However, the heat-treated coating showed two orders of magnitude reduction in fretting wear of the Zr alloy. Wear in the uncoated material involves some local plastic deformation and debris accumulation at the contact interface. In the Al 2 O 3 -coated material, wear occurred by transfer of transparent Al 2 O 3 oxide into the steel pin counterface. Localized removal of coating from the Zirlo alloy flat resulted in a “shark whale” pattern in a scanning electron microscopy image. There was minimal debris accumulation with the heat-treated sample.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Wire Electrical Discharge Machined Surfaces of P91 Steel

The extensive usage of P91 steel in certain reactor components requires its precision fabrication by wire electrical discharge machining (WEDM). The WEDM cut surfaces consist of primarily re-melted and solidified layer (recast layer) of 2-8 µm. The recast layer is a result of fast removal of heat by unaffected metallic substrate and dielectric medium leading to rapid cooling. The WEDM surface is expected to affect the component performance in terms of its corrosion properties. The microstructural changes taking place due to EDM cutting of P91 steel bring about a drastic change in the electrochemical response of surface as compared to that for bulk P91 steel. The surface microstructure is shown to alter the passivation behavior and resistance to localized corrosion. Electrochemical polarization studies were done to evaluate passivation, pitting and intergranular corrosion (IGC) behavior and field emission gun—scanning electron microscopy was used for microstructural characterization of P91 steel surfaces. The passivation behavior for P91 steel WEDM cut surfaces was better than that for diamond polished surface. But pitting corrosion resistance decreased for the P91 steel WEDM surface which is a result of inhomogeneities in the microstructure of recast layer. The IGC resistance though increased due to the decreased grain size in the surface layer.

36 MATERIALS SCIENCE↗

Metal Amorphous Nanocomposite (MANC) Alloy Cores with Spatially Tuned Permeability for Advanced Power Magnetics Applications

Metal amorphous nanocomposite (MANC) alloys are an emerging class of soft magnetic materials showing promise for a range of inductive components targeted for higher power density and higher efficiency power conversion applications including inductors, transformers, and rotating electrical machinery. Magnetization reversal mechanisms within these alloys are typically determined by composition optimization as well as controlled annealing treatments to generate a nanocomposite structure composed of nanocrystals embedded in an amorphous precursor. Here in this paper we demonstrate the concept of spatially varying the permeability within a given component for optimization of performance by using the strain annealing process. The concept is realized experimentally through the smoothing of the flux profile from the inner to outer core radius achieved by a monotonic variation in tension during the strain annealing process. Great potential exists for an extension of this concept to a wide range of other power magnetic components and more complex spatially varying permeability profiles through advances in strain annealing techniques and controls.

36 MATERIALS SCIENCE↗

Pseudo-icosahedral Cr 55 Al 232 - δ as a high-temperature protective material

In this paper, we report here a course of basic research into the potential suitability of a pseudo-icosahedral Cr aluminide as a material for high temperature protective coatings. Cr 55 Al 232-δ [δ = 2.70(6)] exhibits high hardness at room temperature as well as low thermal conductivity and excellent oxidation resistance at 973 K, with an oxidation rate comparable to those of softer, denser benchmark materials. Lastly, the origin of these promising properties can be traced to competing long-range and short-range symmetries within the pseudo-icosahedral crystal structure, suggesting new criteria for future materials research.

36 MATERIALS SCIENCE↗

The Importance of Conducting Life Sciences Experiments on the Deep Space Gateway Platform

Over the last several decades important information has been gathered by conducting life science experiments on the Space Shuttle and on the International Space Station. It is now time to leverage that scientific knowledge, as well as aspects of the hardware that have been developed to support the biological model systems, to NASA's next frontier - the Deep Space Gateway. In order to facilitate long duration deep space exploration for humans, it is critical for NASA to understand the effects of long duration, low dose, deep space radiation on biological systems. While carefully controlled ground experiments on Earth-based radiation facilities have provided valuable preliminary information, we still have a significant knowledge gap on the biological responses of organisms to chronic low doses of the highly ionizing particles encountered beyond low Earth orbit. Furthermore, the combined effects of altered gravity and radiation have the potential to cause greater biological changes than either of these parameters alone. Therefore a thorough investigation of the biological effects of a cis-lunar environment will facilitate long term human exploration of deep space.

microgravity↗

Nuclear Data Sheets for A=217

The evaluated spectroscopic data are presented in this paper for 12 known nuclides with A=217 (Tl, Pb, Bi, Po, At, Rn, Fr, Ra, Ac, Th, Pa, U). For 217Tl, 217Pb, 217Pa, and 217U nuclei, only information on the ground state is available. Levels in 217 Bi are known only from isomer decay following fragmentation reaction and those in 217 At and 217 Rn only from the α decay of 221 Fr and 221 Ra, respectively. High spin levels in 217 Ra are mainly from 1987SuZY and 2011MuZZ which are a lab report and thesis, respectively. Due to differences between these studies, further experimental study is needed to firmly establish the level scheme. This evaluation was carried out as part of a joint IAEA-ICTP workshop for Nuclear Structure and Decay Data, organized and hosted by the IAEA, Vienna and ICTP, Trieste, Aug 22 to Sept 2 2016. The evaluation work was coordinated by E.A. McCutchan (BNL). Finally, this work supersedes the previous previous A=217 evaluation (2003Ak06) by Y.A. Akovali.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Brightness and uniformity measurements of plastic scintillator tiles at the CERN H2 test beam

Here, we study the light output, light collection efficiency and signal timing of a variety of organic scintillators that are being considered for the upgrade of the hadronic calorimeter of the CMS detector. The experimental data are collected at the H2 test-beam area at CERN, using a 150 GeV muon beam. In particular, we investigate the usage of over-doped and green-emitting plastic scintillators, two solutions that have not been extensively considered. We present a study of the energy distribution in plastic-scintillator tiles, the hit efficiency as a function of the hit position, and a study of the signal timing for blue and green scintillators.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Radioactive source calibration test of the CMS Hadron Endcap Calorimeter test wedge with Phase I upgrade electronics

The Phase I upgrade of the CMS Hadron Endcap Calorimeters consists of new photodetectors (Silicon Photomultipliers in place of Hybrid Photo-Diodes) and front-end electronics. The upgrade will eliminate the noise and the calibration drift of the Hybrid Photo-Diodes and enable the mitigation of the radiation damage of the scintillators and the wavelength shifting fibers with a larger spectral acceptance of the Silicon Photomultipliers. The upgrade also includes increased longitudinal segmentation of the calorimeter readout, which allows pile-up mitigation and recalibration due to depth-dependent radiation damage. As a realistic operational test, the responses of the Hadron Endcap Calorimeter wedges were calibrated with a $^{60}$Co radioactive source with upgrade electronics. The test successfully established the procedure for future source calibrations of the Hadron Endcap Calorimeters. Lastly we describe the instrumentation details and the operational experiences related to the sourcing test.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Prompt-delayed $\gamma$-ray spectroscopy with AGATA, EXOGAM and VAMOS++

Here, a new experimental setup to measure prompt-delayed γ-ray coincidences from isotopically identified fission fragments, over a wide time range of 100ns-200μ s, is presented. The fission fragments were isotopically identified, on an event-by-event basis, using the VAMOS++ large acceptance spectrometer. The prompt γ rays emitted at the target position and corresponding delayed γ rays emitted at the focal plane of the spectrometer were detected using, respectively, thirty two crystals of the AGATA γ-ray tracking array and seven EXOGAM HPGe Clover detectors. Finally, fission fragments produced in fusion and transfer-induced fission reactions, using a 238 U beam at an energy of 6.2 MeV/u impinging on a 9 Be target, were used to characterize and qualify the performance of the detection system.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cross section TEM characterization of high-energy-Xe-irradiated U-Mo

U-Mo alloys irradiated with 84 MeV Xe ions to various doses were characterized with transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) techniques. The TEM thin foils were prepared perpendicular to the irradiated surface to allow a direct observation of the entire region modified by ions. Furthermore, depth-selective microstructural information was revealed. Varied irradiation-induced phenomena such as gas bubble formation, phase reversal, and recrystallization were observed at different ion penetration depths in U-Mo.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radiation Information for Designing and Interpreting Biological Experiments Onboard Missions Beyond Low Earth Orbit

There is growing interest in flying biological experiments beyond low-Earth orbit (LEO) to measure biological responses potentially relevant to those expected during a human mission to Mars. Such experiments could be payloads onboard precursor missions, including unmanned private-public partnerships, as well as small low-cost spacecraft (satellites) designed specifically for biosentinel type missions. Designing such experiments requires knowledge of the radiation environment and its interactions with both the spacecraft and the experimental payload. Information is provided here that is useful for designing such experiments.

radiation↗

Using NASA's GeneLab for VESGEN Systems Analysis of Vascular Phenotypes from Stress and Other Signaling Pathways

One fundamental requirement shared by humans with all higher terrestrial life forms, including other vertebrates, insects, and higher land plants, is a complex, fractally branching vascular system. NASA's VESsel GENeration Analysis (VESGEN) software maps and quantifies vascular trees, networks, and tree-network composites according to weighted physiological rules such as vessel connectivity, tapering and bifurcational branching. According to fluid dynamics, successful vascular transport requires a complex distributed system of highly regulated laminar flow. Microvascular branching rules within vertebrates, dicot leaves and the other organisms therefore display many similarities. A unifying perspective is that vascular patterning offers a useful readout of molecular signaling that necessarily integrates these complex pathways. VESGEN has elucidated changes in vascular pattern resulting from inflammatory, developmental and other signaling within numerous tissues and major model organisms studied for Space Biology. For a new VESGEN systems approach, we analyzed differential gene expression in leaves of Arabidopsis thaliana reported by GeneLab (GLDS-7) for spaceflight. Vascularrelated changes in leaf gene expression were identified that can potentially be phenocopied by mutants in ground-based experiments. To link transcriptional, protein and other molecular change with phenotype, alterations in the spatial and dynamic dimensions of vascular patterns for Arabidopsis leaves and other model species are being co-localized with signaling patterns of single molecular expression analyzed as information dimensions. Previously, Drosophila microarray data returned from space suggested significant changes in genes related to wing venation development that include EGF, Notch, Hedghog, Wingless and Dpp signaling. Phenotypes of increasingly abnormal ectopic wing venation in the (non-spaceflight) Drosophila wing generated by overexpression of a Notch antagonist were analyzed by VESGEN. Other VESGEN research applications include the mouse retina, GI and coronary vessels, avian placental analogs and translational studies in the astronaut retina related to health challenges for long-duration missions.

Venation↗

Dose rate effects in the radiation damage of the plastic scintillators of the CMS hadron endcap calorimeter

We present measurements of the reduction of light output by plastic scintillators irradiated in the CMS detector during the 8 TeV run of the Large Hadron Collider and show that they indicate a strong dose rate effect. The damage for a given dose is larger for lower dose rate exposures. The results agree with previous measurements of dose rate effects, but are stronger due to the very low dose rates probed. Here, we show that the scaling with dose rate is consistent with that expected from diffusion effects.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Advanced synthesis for enhanced accident tolerant of LWR cladding materials

Advanced materials synthesis is utilized at Argonne National Laboratory (ANL) with the intended goal of improving performance of light water reactor (LWR) claddings under normal operation and accident conditions. The advanced synthesis utilizes atomic layer deposition (ALD) techniques to infiltrate SiC wires wrapped around ZIRLO tubes with SiC deposits, to form a SiC-SiC composite on the ZIRLO tubes. This paper reports on the effort to deposit SiC using ALD. The deposition was successful in infiltrating deep into the wires structure, reaching the surface of the ZIRLO tubes, as indicated through different characterization techniques. Because of the slow deposition rate of SiC, only a limited amount of SiC was deposited (a few hundreds of nm of SiC thick layers). This was followed by a few micrometers of ALD deposition of zircon (ZrSiO{sub 4}.) on top of the SiC deposition. The additional deposition was adequate to hold the wires together around the tube. Work is ongoing to increase the SiC ALD deposition rate, and infiltrate the larger pores within the wires with other SiC deposition methods such as low temperature chemical vapor deposition (CVD). (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗