Engineering Papers⌕ Search

Engineering topics

Berry, Ray A

Publications and source records attributed to Berry, Ray A.

A CFD Simulation Process for Fast Reactor Fuel Assemblies

A CFD modeling and simulation process for large-scale problems using an arbitrary fast reactor fuel assembly design was evaluated. Three-dimensional flow distributions of sodium for several fast reactor fuel assembly pin spacing configurations were simulated on high performance computers using commercial CFD software. This research focused on 19-pin fuel assembly “benchmark” geometry, similar in design to the Advanced Burner Test Reactor, where each pin is separated by helical wire-wrap spacers. Several two-equation turbulence models including the k–e and SST (Menter) k–? were evaluated. Considerable effort was taken to resolve the momentum boundary layer, so as to eliminate the need for wall functions and reduce computational uncertainty. High performance computers were required to generate the hybrid meshes needed to predict secondary flows created by the wire-wrap spacers; computational meshes ranging from 65 to 85 million elements were common. A general validation methodology was followed, including mesh refinement and comparison of numerical results with empirical correlations. Predictions for velocity, temperature, and pressure distribution are shown. The uncertainty of numerical models, importance of high fidelity experimental data, and the challenges associated with simulating and validating large production-type problems are presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of Natural Convection Flows Under VHTR Type Conditions Modeled by both the Conservation and Incompressible Forms of the Navier-Stokes Equations

This manuscript illustrates a comparative study to analyze the physical differences between numerical simulations obtained with both the conservation and incompressible forms of the Navier-Stokes equations for natural convection flows in simple geometries. The purpose of this study is to quantify how the incompressible flow assumption (which is based upon constant density advection, divergence-free flow, and the Boussinesq gravitational body force approximation) differs from the conservation form (which only assumes that the fluid is a continuum) when solving flows driven by gravity acting upon density variations resulting from local temperature gradients. Driving this study is the common use of the incompressible flow assumption in fluid flow simulations for nuclear power applications in natural convection flows subjected to a high heat flux (large temperature differences). A series of simulations were conducted on two-dimensional, differentially-heated rectangular geometries and modeled with both hydrodynamic formulations. From these simulations, the selected characterization parameters of maximum Nusselt number, average Nusselt number, and normalized pressure reduction were calculated. Comparisons of these parameters were made with available benchmark solutions for air with the ideal gas assumption at both low and high heat fluxes. Additionally, we generated specific force quantities and velocity and temperature distributions to provide a basis for further analysis. The simulations and analysis were then extended to include helium at the Very High Temperature gas-cooled Reactor (VHTR) normal operating conditions. Our results show that the consequences of incorporating the incompressible flow assumption in high heat flux situations may lead to unrepresentative results. The results question the use of the incompressible flow assumption for simulating fluid flow in an operating nuclear reactor, where large temperature variations are present.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Preliminary Investigation of Rapid Depressurization Phenomena Following a Sudden DLOFC in a VHTR

Air ingress has been identified as a potential threat for Very High Temperature gas-cooled Reactors (VHTR). Reactor components constructed of graphite will, at high temperatures, produce exothermic reactions in the presence of oxygen. The danger lies in the possibility of fuel element damage and core structural failure. Previous investigations of air ingress mechanisms have focused on thermal and molecular diffusion, density-driven stratified flow due to hydrodynamic instability, and natural convection. Here, we investigate the possibility of a rapid flow reversal of helium coolant due to a Taylor (rarefaction) wave expansion after a hypothetical sudden Depressurized Loss of Forced Cooling (DLOFC) scenario in a VHTR. Conceivably, flow reversal of the helium coolant could entrain significant quantities of air into the reactor vessel. Our analysis starts with a one-dimensional shock tube simulation to simply illustrate the development of a Taylor wave with resulting reentrant flow. Then, a simulation is performed of an idealized two-dimensional axisymmetric representation of the lower plenum of General Atomics GT-MHR subjected to a hypothetical catastrophic break of the hot duct. Analysis shows the potential for significant and rapid air ingress into the reactor vessel in the case of a large break in the cooling system.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The Discrete Equation Method (DEM) for Fully Compressible Two-Phase Flows in Ducts of Spatially Varying Cross-Section

Typically, multiphase modeling begins with an averaged (or homogenized) system of partial differential equations (traditionally ill-posed) then discretizes this system to form a numerical scheme. Assuming that the ill-posedness problem is avoided by using a well-posed formulation such as the seven-equation model, this presents problems for the numerical approximation of non-conservative terms at discontinuities (interfaces, shocks) as well as unwieldy treatment of fluxes with seven waves. To solve interface problems without conservation errors and to avoid this questionable determination of average variables and the numerical approximation of the non-conservative terms associated with 2 velocity mixture flows we employ a new homogenization method known as the Discrete Equations Method (DEM). Contrary to conventional methods, the averaged equations for the mixture are not used, and this method directly obtains a (well-posed) discrete equation system from the single-phase system to produce a numerical scheme which accurately computes fluxes for arbitrary numbers of phases and solves non-conservative products. The method effectively uses a sequence of single phase Riemann equation solves. Phase interactions are accounted for by Riemann solvers at each interface. Flow topology can change with changing expressions for the fluxes. Non-conservative terms are correctly approximated. Some of the closure relations missing from the traditional approach are automatically obtained. Lastly, we can often times identify the continuous equation system, resulting from taking the continuous limit with weak wave assumptions, of the discrete equations. This can be very useful from a theoretical standpoint. As a first step toward implict integration of the DEM method in multidimensions, in this paper we construct a DEM model for the flow of two compressible phases in 1-D ducts of spatially varying cross-section to test this approach. To relieve time step size restrictions due to stiffness and to achieve tighter coupling of equations, a fully implicit time integration method is employed. For the first time, we demonstrate on a converging-diverging two-phase nozzle that this well-posed, 2 pressure, 2 velocity DEM model can be integrated to a meaningful steady-state with both phases treated as compressible.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Simple and Efficient Diffuse Interface Method for Compressible Two-Phase Flows

In nuclear reactor safety and optimization there are key issues that rely on in-depth understanding of basic two-phase flow phenomena with heat and mass transfer. For many reasons, to be discussed, there is growing interest in the application of two-phase flow models to provide diffuse, but nevertheless resolved, simulation of interfaces between two immiscible compressible fluids – diffuse interface method (DIM). Because of its ability to dynamically create interfaces and to solve interfaces separating pure media and mixtures for DNS-like (Direct Numerical Simulation) simulations of interfacial flows, we examine the construction of a simple, robust, fast, and accurate numerical formulation for the 5-equation Kapila et al. [1] reduced two-phase model. Though apparently simple, the Kapila et al. model contains a volume fraction differential transport equation containing a nonlinear, non-conservative term which poses serious computational challenges. To circumvent the difficulties encountered with the single velocity and single pressure Kapila et al. [1] multiphase flow model, a 6-equation relaxation hyperbolic model is built to solve interface problems with compressible fluids. In this approach, pressure non-equilibrium is first restored, followed by a relaxation to an asymptotic solution which is convergent to the solutions of the Kapila et al. reduced model. The apparent complexity introduced with this extended hyperbolic model actually leads to considerable simplifications regarding numerical resolution, and the various ingredients used by this method are general enough to consider future extensions to problems involving complex physics.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗