Engineering Papers⌕ Search

Engineering topics

Bermel, Peter

Publications and source records attributed to Bermel, Peter.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Concurrent characterization of GaN MOSHEMT gate leakage via electrical and thermoreflectance measurements

In this work, we report the first concurrent use of electrical and thermal characterization, via thermoreflectance, to analyze Time Dependent Dielectric Breakdown in GaN MOSHEMTs. Electrically stressing the devices until a failure occurs, then evaluating them via thermoreflectance, revealed a geometric dependence of the failure mode. Further, all soft breakdowns occurred at the mesa edge where the electric field strength was at its strongest, and tunneling current density was at its highest. This breakdown phenomenon at the mesa edge has been seen previously in GaN HEMTs employing a mesa architecture. Possible approaches to mitigate these failures in MOSHEMTs are proposed.

42 ENGINEERING↗
DOE OSTI2021

Xenon implantation of nanodiamond films for targeted color center emission at sub-nanosecond time scales

In this work, the lifetime of nitrogen-vacancy color centers within nanodiamonds is reduced from 550±13 ps to 297±10 ps through the implantation of xenon. Coupled-mode analysis is employed to characterize the mechanism responsible for the reduction in emission lifetime. The observed spectral lineshape is found to be consistent with a Voigt profile consisting of two Lorentzian resonant peaks at 637 nm and 811 nm that are inhomogeneously broadened by a Gaussian distribution. A convolution of the frequency-domain Lorentzian output, with linewidths less than 1 nm, from the coupled-mode system of equations with a Gaussian with standard deviation of 85 nm is performed to generate the Voigt profile. The shortened emission lifetime is found to be consistent with a coupled mode theory model incorporating coupling between nitrogen-vacancy and xenon-vacancy color centers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhancement of Photovoltaic Current through Dark States in Donor–Acceptor Pairs of Tungsten–Based Transition Metal Di–Chalcogenides

As several photovoltaic materials experimentally approach the Shockley– Queisser limit, there has been a growing interest in unconventional materials and approaches with the potential to cross this efficiency barrier. One such candidate is dark state protection induced by the dipole–dipole interaction between molecular excited states. This phenomenon has been shown to significantly reduce carrier recombination rate and enhance photon-to-current conversion, in elementary models consisting of few interacting chromophore centers. Atomically thin 2D transition metal di-chalcogenides (TMDCs) have shown great potential for use as ultrathin photovoltaic materials in solar cells due to their favorable photon absorption and electronic transport properties. TMDC alloys exhibit tunable direct bandgaps and significant dipole moments. In this work, the dark state protection mechanism has been introduced to a TMDC based photovoltaic system with pure tungsten diselenide (WSe 2 ) as the acceptor material and the TMDC alloy tungsten sulfo-selenide (WSeS) as the donor material. Furthermore, our numerical model demonstrates the first application of the dark state protection mechanism to a photovoltaic material with a photon current enhancement of up to 35% and an ideal photon-to-current efficiency exceeding the Shockley–Queisser limit.

36 MATERIALS SCIENCE↗
DOE OSTI2019

High-temperature, spectrally-selective, scalable, and flexible thin-film Si absorber and emitter

Solar thermal technologies have great potential to provide low-cost storage for solar energy. However, their efficiencies are limited by a lack of scalable, mechanically flexible, durable, yet highly-efficient spectrally-selective solar absorbers suitable for high temperatures at low solar concentrations. Here, we overcome these challenges by fabricating a scalable free-standing spectrally-selective thin-film Si absorber and emitter (SSTFS) composite. Its high-temperature emittance shows strong spectral selectivity, even at 595 °C. Thermal stability is proven by measuring optical properties before and after thermal cycling equivalent to one day of concentrated sunlight. Despite the use of crystalline Si, the fabricated SSTFS composite exhibits exceptional mechanical flexibility to cover most surface geometries. The SSTFS composite demonstrates the potential of high-temperature, efficient and flexible solar absorbers and thermal emitters to advance renewable solar energy with storage.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Observation and Implications of Composition Inhomogeneity Along Grain Boundaries in Thin Film Polycrystalline CdTe Photovoltaic Devices

Abstract Leading photovoltaic technologies such as multicrystalline Si, CdTe, Cu(In,Ga)Se 2 , and lead halide perovskites are polycrystalline, yet achieve relatively high performance. At the moment polycrystalline photovoltaic technologies stand at a juncture where further advances in device performance and reliability necessitate additional characterization and modeling to include nanoscale property variations. Properties and implications of grain boundaries are previously studied, yet chemistry variations along individual grain boundaries and its implications are not yet fully explored. Here, the effects of bromine etching of CdTe absorber layers on the nanoscale chemistry are reported. Bromine etching is commonly used for improving CdTe back contacts, yet it removes both cadmium and chlorine along grain boundaries to depths closer to 1 µm. 2D device simulations reveal these composition modifications limit photovoltaic performance. Since grain boundaries and their intersections with surfaces and interfaces are universal to thin film photovoltaics, these findings call for similar studies in each of the photovoltaic technologies to further enable advances.

Misra, Sudhajit↗
DOE OSTI2019

Sesame: A 2-dimensional solar cell modeling tool

This work introduces a new software package “Sesame” for the numerical computation of classical semiconductor equations. It supports 1 and 2-dimensional systems and provides tools to easily implement extended defects such as grain boundaries or sample surfaces. Sesame is designed to facilitate fast exploration of the system parameter space and to visualize local charge transport properties. Sesame has been benchmarked against other software packages, and results for single crystal and polycrystalline CdS-CdTe heterojunctions are presented. Sesame is distributed as a Python package or as a standalone GUI application, and is available at https://pages.nist.gov/sesame/.

14 SOLAR ENERGY↗
DOE OSTI2019

Ground sculpting to enhance energy yield of vertical bifacial solar farms

The prospect of additional energy yield and improved reliability have increased commercial interest in bifacial solar modules. Recent publications have quantified the bifacial gain for several configurations. For example, a standalone, optimally-tilted bifacial panel placed over a flat ground (with 50% albedo) is expected to produce a bifacial energy gain of 30% (per module area). In contrast, self and mutual shading in a farm with periodically spaced panels reduces the bifacial gain to 10–15% (per farm area). Bifacial gain is negligible for vertical arrays—although the configuration is of significant interest since it can prevent soiling. Here, we calculate the bifacial gain of a solar farm where vertical arrays are placed over sculpted/patterned ground. We conclude that vertical panels straddling (upward) triangle-shaped ground maximizes the energy output. Our worldwide calculation with up-triangle ground configuration and 50% albedo leads to the following conclusion. Compared to a traditional tilted monofacial design, the bifacial gain is (i) small up to 20° latitude, (ii) increases to 50% at 40° latitude, and (iii) reaches up to 100% at 60° latitude. Overall, high bifacial gains are observed in many regions particularly those with moderate to low clearness index. The enhanced output, along with reduced soiling loss and lower cleaning cost of the ground sculpted vertical bifacial (GvBF) solar farm could be of significant technological interest, especially in regions such as the Middle East and North Africa (MENA) susceptible to significant soiling losses.

14 SOLAR ENERGY↗
DOE OSTI2018

Discriminating electromagnetic radiation based on angle of incidence

The present invention provides systems, articles, and methods for discriminating electromagnetic radiation based upon the angle of incidence of the electromagnetic radiation. In some cases, the materials and systems described herein can be capable of inhibiting reflection of electromagnetic radiation (e.g., the materials and systems can be capable of transmitting and/or absorbing electromagnetic radiation) within a given range of angles of incidence at a first incident surface, while substantially reflecting electromagnetic radiation outside the range of angles of incidence at a second incident surface (which can be the same as or different from the first incident surface). A photonic material comprising a plurality of periodically occurring separate domains can be used, in some cases, to selectively transmit and/or selectively absorb one portion of incoming electromagnetic radiation while reflecting another portion of incoming electromagnetic radiation, based upon the angle of incidence. In some embodiments, one domain of the photonic material can include an isotropic dielectric function, while another domain of the photonic material can include an anisotropic dielectric function. In some instances, one domain of the photonic material can include an isotropic magnetic permeability, while another domain of the photonic material can include an anisotropic magnetic permeability. In some embodiments, non-photonic materials (e.g., materials with relatively large scale features) can be used to selectively absorb incoming electromagnetic radiation based on angle of incidence.

Hamam, Rafif E.↗
DOE OSTI2018

Self-Assembled Ag–TiN Hybrid Plasmonic Metamaterial: Tailorable Tilted Nanopillar and Optical Properties

Key challenges limiting the adoption of metallic plasmonic nanostructures for practical devices include structural stability and the ease of large-scale fabrication. Overcoming these issues may require novel metamaterial fabrication with potentials for improved durability under extreme conditions. Here, in this paper, a self-assembled growth of a hybrid plasmonic metamaterial in thin-film form is reported, with epitaxial Ag nanopillars embedded in TiN, a mechanically strong and chemically inert matrix. One of the key achievements lies in the successful control of the tilt angle of the Ag nanopillars (from 0° to 50°), which is attributed to the interplay between the growth kinetics and thermodynamics during deposition. Such an anisotropic nature offered by the tilted Ag nanopillars in TiN matrix is crucial for achieving broadband, asymmetric optical selectivity. Optical spectra coupled with numerical simulations demonstrate strong plasmonic resonance, as well as angular selectivity in a broad UV–vis to near-infrared regime. The nanostructured metamaterials in this work, which consist of highly conductive metallic nanopillars in a durable nitride matrix, have the potential to serve as a novel hybrid material platform for highly tailorable nanoscale metamaterial designs, suitable for high temperature optical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Electronic and optical properties of ultra-thin 2D tungsten disulfide for photovoltaic applications

Atomically thin 2D layered semiconductor materials such as Transition Metal Di-Chalcogenides (TMDCs) have great potential for use as flexible, ultra-thin photovoltaic materials in solar cells due to their favorable photon absorption and electronic transport properties. The electronic properties, such as band structure and bandgap, and optical absorption properties of Tungsten Disulfide (WS 2 ) were obtained from Density Functional Theory (DFT) calculations; the properties of WS 2 make it a favorable photovoltaic material. Using these properties, we have modelled, using numerical calculations and simulations, a solar cell based on monolayer and bulk WS 2 together with amorphous silicon (a-Si). The maximum efficiency of this cell is 23.26% with V OC of 0.843 V and J SC of 33.49 mA/cm 2 . The performance of our solar cell is comparable to many commercial cells. The results show how monolayer WS 2 can serve as a suitable photovoltaic material, opening possibilities to develop solar cells based on 2D TMDC materials.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Thermoreflectance imaging of electromigration evolution in asymmetric aluminum constrictions

Electromigration (EM) is a phenomenon whereby the flow of current in metal wires moves the underlying atoms, potentially inducing electronic interconnect failures. The continued decrease in commercial lithographically defined feature sizes means that EM presents an increasing risk to the reliability of modern electronics. To mitigate these risks, it is important to look for novel mechanisms to extend lifetime without forfeiting miniaturization. Typically, only the overall increase in the interconnect resistance and failure voltage are characterized. However, if the current flows non-uniformly, spatially resolving the resulting hot spots during electromigration aging experiments may provide better insights into the fundamental mechanisms of this process. Here in this study, we focus on aluminum interconnects containing asymmetric reservoir and void pairs with contact pads on each end. Such reservoirs are potential candidates for self-healing. Thermoreflectance imaging was used to detect hot spots in electrical interconnects at risk of failure as the voltage was gradually increased. It reveals differential heating with increasing voltage for each polarity. We find that while current flow going from a constriction to a reservoir causes a break at the void, the identical structure with the opposite polarity can sustain higher current (J = 21 × 10 6 A/cm 2 ) and more localized joule heating and yet is more stable. Ultimately, a break takes place at the contact pad where the current flows from narrow interconnect to larger pads. In summary, thermoreflectance imaging with submicron spatial resolution provides valuable information about localized electromigration evolution and the potential role of reservoirs to create more robust interconnects.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2017

Thermophotovoltaics with spectral and angular selective doped-oxide thermal emitters

Deliberate control of thermal emission properties using nanophotonics has improved a number of applications including thermophotovoltaics (TPV), radiative cooling and infrared spectroscopy. In this work, we study the effect of simultaneous control of angular and spectral properties of thermal emitters on the efficiencies of TPV systems. While spectral selectivity reduces sub-bandgap losses, angular selectivity is expected to enhance view factors at larger separation distances and hence to provide flexibilities in cooling the photovoltaic converter. We propose a design of an angular and spectral selective thermal emitter based on waveguide perfect absorption phenomena in epsilon-near-zero thin-films. Aluminum-doped Zinc-Oxide is used as an epsilon-near-zero material with a cross-over frequency in the near-infrared. A high contrast grating is designed to restrict the emission in a range of angles around the normal direction, while an integrated filter ensures spectral selectivity to reduce sub-bandgap losses. Theoretical analysis shows an expected relative enhancement of the TPV system efficiency of at least 32% using selective emitters with ideal angular and spectral selectivity at large separation distances compared to a blackbody. This enhancement factor, however, reduces to 3.9% with non-ideal selective emitters. This big reduction of the efficiency is attributed to sub-bandgap losses, off-angular losses and high-temperature dependence of optical constants.

42 ENGINEERING↗
DOE OSTI2017

Radiative sky cooling: fundamental physics, materials, structures, and applications

Radiative sky cooling reduces the temperature of a system by promoting heat exchange with the sky; its key advantage is that no input energy is required. We will review the origins of radiative sky cooling from ancient times to the modern day, and illustrate how the fundamental physics of radiative cooling calls for a combination of properties that may not occur in bulk materials. A detailed comparison with recent modeling and experiments on nanophotonic structures will then illustrate the advantages of this recently emerging approach. Potential applications of these radiative cooling materials to a variety of temperature-sensitive optoelectronic devices, such as photovoltaics, thermophotovoltaics, rectennas, and infrared detectors, will then be discussed. This review will conclude by forecasting the prospects for the field as a whole in both terrestrial and space-based systems.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Directing solar photons to sustainably meet food, energy, and water needs

As we approach a “Full Earth” of over ten billion people within the next century, unprecedented demands will be placed on food, energy and water (FEW) supplies. The grand challenge before us is to sustainably meet humanity’s FEW needs using scarcer resources. To overcome this challenge, we propose the utilization of the entire solar spectrum by redirecting solar photons to maximize FEW production from a given land area. We present novel solar spectrum unbundling FEW systems (SUFEWS), which can meet FEW needs locally while reducing the overall environmental impact of meeting these needs. The ability to meet FEW needs locally is critical, as significant population growth is expected in less-developed areas of the world. As a result, the proposed system presents a solution to harness the same amount of solar products (crops, electricity, and purified water) that could otherwise require ~60% more land if SUFEWS were not used—a major step for Full Earth preparedness.

14 SOLAR ENERGY↗
DOE OSTI2017

Collimated thermal radiation transfer via half Maxwell's fish-eye lens for thermophotovoltaics

Thermophotovoltaics (TPV) convert heat into electricity by capturing thermal radiation with a photovoltaic (PV) cell, ideally at efficiencies of 50% or more. However, excess heating of the PV cell from close proximity to the emitter substantially reduces the system efficiency. In this paper, we theoretically develop and numerically demonstrate an approach to fundamentally improving TPV systems that allow for a much greater separation of an emitter and a receiver. Thus, we solve the excess heating dilemma, required for achieving theoretically high efficiencies. It consists of a spherically graded index lens known as Maxwell's Fish-Eye (MFE) structure, capable of collimating hemispherical emission into a much narrower range of angles, close to the normal direction. To fully characterize the power radiation profile of the MFE, we perform finite-difference time-domain simulations for a quarter MFE and then map it onto a Gaussian beam approximation. The modeled beam properties are subsequently used to study a half MFE. In an optimized half MFE design, 90% of all thermal photons reach a receiver at a distance of 100 λ; by comparison, only 15.6% of a blackbody emitter reach a receiver in the same geometry. It is also shown that the emission achieved by a half MFE can lead to a photon recycling rate above 95% for below bandgap photons at an emitter-receiver separation of 100 λ. Finally, by applying a half MFE, the absolute TPV efficiency can be improved from 5.74% to 37.15%, which represents a significant step forward in realizing high-efficiency TPV systems.

30 DIRECT ENERGY CONVERSION↗