Engineering Papers⌕ Search

Engineering topics

Berg, J S

Publications and source records attributed to Berg, J S.

Acceleration in the linear non-scaling fixed-field alternating-gradient accelerator EMMA

In a fixed-field alternating-gradient (FFAG) accelerator, eliminating pulsed magnet operation permits rapid acceleration to synchrotron energies, but with a much higher beam-pulse repetition rate. Conceived in the 1950s, FFAGs are enjoying renewed interest, fuelled by the need to rapidly accelerate unstable muons for future high-energy physics colliders. Until now a 'scaling' principle has been applied to avoid beam blow-up and loss. Removing this restriction produces a new breed of FFAG, a non-scaling variant, allowing powerful advances in machine characteristics. We report on the first non-scaling FFAG, in which orbits are compacted to within 10?mm in radius over an electron momentum range of 12-18 MeV/c. In this strictly linear-gradient FFAG, unstable beam regions are crossed, but acceleration via a novel serpentine channel is so rapid that no significant beam disruption is observed. This result has significant implications for future particle accelerators, particularly muon and high-intensity proton accelerators.

43 PARTICLE ACCELERATORS↗

A Non-scaling Fixed Field Alternating Gradient Accelerator for the Final Acceleration Stage of the International Design Study of the Neutrino Factory.

The International Design Study of the Neutrino Factory (IDS-NF) has recently completed its Interim Design Report (IDR), which presents our current baseline design of the neutrino factory. To increase the efficiency and reduce the cost of acceleration, the IDR design uses a linear non-scaling fixed field alternating gradient accelerator (FFAG) for its final acceleration stage. We present the current lattice design of that FFAG, including the main ring plus its injection and extraction systems. We describe parameters for the main ring magnets, kickers, and septa, as well as the power supplies for the kickers. We present a first pass at an engineering layout for the ring and its subsystems.

43 PARTICLE ACCELERATORS↗

Status of Studies of Achromat-based 6D Ionization Cooling Rings for Muons

Six dimensional ionization cooling of muons is needed to achieve the necessary luminosity for a muon collider. If that cooling could occur over multiple turns in a closed ring, there would be significant cost savings over a single-pass cooling channel. We report on the status of a cooling ring with achromatic arcs. The achromatic design permits the design to easily switch between a closed ring and a snaking geometry on injection or extraction from the ring. The ring is designed with sufficient space in each superperiod for injection and extraction magnets. We describe the ring's lattice design, performance, and injection/extraction requirements.

43 PARTICLE ACCELERATORS↗

A Pion Production and Capture System for a 4 MW Target Station

A study of a pion production and capture system for a 4 MW target station for a neutrino factory or muon collider is presented. Using the MARS code, we simulate the pion production produced by the interaction of a free liquid mercury jet with an intense proton beam. We study the variation of meson production with the direction of the proton beam relative to the target. We also examine the influence on the meson production by the focusing of the proton beam. The energy deposition in the capture system is determined and the shielding required in order to avoid radiation damage is discussed. The exploration for the multiple proton beam entry directions relative to mercury jet in the 8GeV proton beam case demonstrates that an asymmetric layout is required in order to achieve the same beam/jet crossing angle at the jet axis. We find a correlation between the distance of beam relative to the jet and the meson production. The peak meson production is 8% higher than for the lowest case. The examination of the influence on the meson production by the focusing of the proton beam shows the meson production loss is negligible (<1%) for a beta function to be 0.3m or higher for the proton beam. By investigating the energy deposition in the target/capture system, we see that the bulk of 4-MW proton beam power is deposited in the water cooled tungsten-carbide (WC) shielding, the mercury jet and the capture beam pipe. In addition, high power deposition in the first superconducting coil causes an issue for its operation and life time. Enhanced shielding is necessary to lower the radiation damage.

43 PARTICLE ACCELERATORS↗

Meson Production Simulations for a Mercury Jet Target

A study of target parameters for a high-power, liquid mercury jet target system for a neutrino factory or muon collider is presented. Using the MARS15 code, we simulate particle production initiated by incoming protons below the jet with kinetic energies between 2 and 100 GeV. For each proton beam energy, we maximize production by varying the geometric parameters of the target: the mercury jet radius, the incoming proton beam angle, and the crossing angle between the mercury jet and the proton beam. With an 8 GeV proton beam, we study the variation of meson production with the direction of the proton beam relative to the jet.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

FFAG Designs for the International Design Study for the Neutrino Factory

The International Design Study for the Neutrino Factory (IDS-NF) aims to produce a design report for a neutrino factory. One component of that design is a linear nonscaling fixed-field alternating gradient accelerator (FFAG) that will accelerate to the final energy of 25 GeV. An FFAG is used to reduce the machine cost by maximizing the number of passes made through the RF cavities. We present some design options for this FFAG, individually optimized for cost. We study the addition of nonlinear magnets to the lattice to improve the performance of the lattice and consider the negative effects of doing so.

43 PARTICLE ACCELERATORS↗

AN INJECTION/EXTRACTION SCENARIO FOR EMMA

EMMA is an experiment to study beam dynamics in a linear non-scaling fixed-field alternating gradient accelerator (FFAG). It accelerates an electron beam from 10 to 20 MeV kinetic energy. To optimally perform these studies, one must be able to inject the beam at any energy within the machine's energy range. Furthermore, because we wish to study the behavior of large-emittance beams in such a machine, the injection systems must be able to inject the beam anywhere within a transverse phase space ellipse with a normalized acceptance of 3 mm, and the extraction systems must be able to extract from that same ellipse. I describe a computation of kicker and septum fields to achieve all of these requirements, and discuss how this interacts with the hardware constraints.

43 PARTICLE ACCELERATORS↗

The EMMA Main Ring Lattice.

I give a brief introduction to the purpose and goals of the EMMA experiment and describe how they will impact the design of the main EMMA ring. I then describe the mathematical model that is used to describe the EMMA lattice. Finally, I show how the different lattice configurations were obtained and list their parameters.

43 PARTICLE ACCELERATORS↗

Accelerator Design Concept for Future Neutrino Facilities

This document summarizes the findings of the Accelerator Working Group (AWG) of the International Scoping Study (ISS) of a Future Neutrino Factory and Superbeam Facility. The work of the group took place at three plenary meetings along with three workshops, and an oral summary report was presented at the NuFact06 workshop held at UC-Irvine in August, 2006. The goal was to reach consensus on a baseline design for a Neutrino Factory complex. One aspect of this endeavor was to examine critically the advantages and disadvantages of the various Neutrino Factory schemes that have been proposed in recent years.

43 PARTICLE ACCELERATORS↗