Engineering topics

Bent, Stacey F.

Publications and source records attributed to Bent, Stacey F..

4 records

DOE OSTI2024

Dynamics of precatalyst conversion and iron incorporation in nickel-based alkaline oxygen evolution reaction catalysts

The efficiency of alkaline water electrolyzers is limited by the oxygen evolution reaction (OER). The design of improved OER catalysts requires understanding of material changes induced by the electrolyte under oxidizing potentials. We compare four Ni-based thin-film precatalysts—Ni, NiO, Ni(OH) 2 , and NiS x —in 0.1 M KOH with and without Fe impurities. Precatalyst conversion to the active oxyhydroxide catalysts and their OER performance are induced and followed using cyclic voltammetry. Without Fe electrolyte impurities, the precatalysts convert at different rates to a similar, modestly active NiOOH catalyst. Added Fe impurities are incorporated concurrently with the oxyhydroxide formation leading to active Ni 1-x Fe x OOH catalysts. The NiS x and Ni(OH) 2 precatalysts rapidly convert to oxyhydroxides both with and without Fe, while conversion of Ni and especially NiO is slowed down by Fe impurities. Choice of the precatalyst and presence of Fe impurities are key factors in designing active Ni 1-x Fe x OOH OER catalysts for electrolyzers.

alkaline electrolysis↗

DOE OSTI2024

Deconvoluting Effects of Lithium Morphology and SEI Stability at Moderate Current Density Using Interface Engineering

Lithium (Li)-morphology and solid electrolyte interphase (SEI) are among the most significant performance regulators in Li-metal batteries (LMBs). While both Li-morphology and SEI composition play key roles in the cyclability of LMBs, less is understood about the individual contributions of each factor to overall Li reversibility, particularly at a practical current density (1 mA cm −2 ) at which the kinetics of both factors are not naturally separated. Herein, an interface engineering approach is introduced to deconvolute the impacts of Li-morphology and SEI composition on battery performance. By using interfacial nanofilms with differing resistivity (resistive HfO 2 versus conductive ZnO), the morphology of Li is varied, and by virtue of similar acidic character of the nanofilms, the formation of anion-rich SEIs is maintained. It is established that although the surface acidity of the thin films enables preformation of a more anion-rich SEI, it is not preserved after Li plating. It is further shown that resistance-controlled, low-surface-area Li-morphology exhibits up to threefold increase in stable cycle life when tested in multiple electrolytes. Overall, these findings explain why Li-morphological control is more advantageous for performance improvement than preformed SEI modulation due to the inherent challenges in SEI preservation.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Unveiling the Stability of Encapsulated Pt Catalysts Using Nanocrystals and Atomic Layer Deposition

Platinum exhibits desirable catalytic properties, but it is scarce and expensive. Optimizing its use in key applications such as emission control catalysis is important to reduce our reliance on such a rare element. Supported Pt nanoparticles (NPs) used in emission control systems deactivate over time because of particle growth in sintering processes. Here, in this work, we shed light on the stability against sintering of Pt NPs supported on and encapsulated in Al 2 O 3 using a combination of nanocrystal catalysts and atomic layer deposition (ALD) techniques. We find that small amounts of alumina overlayers created by ALD on preformed Pt NPs can stabilize supported Pt catalysts, significantly reducing deactivation caused by sintering, as previously observed by others. Combining theoretical and experimental insights, we correlate this behavior to the decreased propensity of oxidized Pt species to undergo Ostwald ripening phenomena because of the physical barrier imposed by the alumina overlayers. Furthermore, we find that highly stable catalysts can present an abundance of under-coordinated Pt sites after restructuring of both Pt particles and alumina overlayers at a high temperature (800 °C) in C 3 H 6 oxidation conditions. The enhanced stability significantly improves the Pt utilization efficiency after accelerated aging treatments, with encapsulated Pt catalysts reaching reaction rates more than two times greater than those of a control supported Pt catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Dissolution of the Solid Electrolyte Interphase and Its Effects on Lithium Metal Anode Cyclability

At >95% Coulombic efficiencies, most of the capacity loss for Li metal anodes (LMAs) is through the formation and growth of the solid electrolyte interphase (SEI). However, the mechanism through which this happens remains unclear. One property of the SEI that directly affects its formation and growth is the SEI’s solubility in the electrolyte. Here, in this work, we systematically quantify and compare the solubility of SEIs derived from ether-based electrolytes optimized for LMAs using in-operando electrochemical quartz crystal microbalance (EQCM). A correlation among solubility, passivity, and cyclability established in this work reveals that SEI dissolution is a major contributor to the differences in passivity and electrochemical performance among battery electrolytes. Together with our EQCM, X-ray photoelectron spectroscopy (XPS), and nuclear magnetic resonance (NMR) spectroscopy results, we show that solubility depends on not only the SEI’s composition but also the properties of the electrolyte. This provides a crucial piece of information that could help minimize capacity loss due to SEI formation and growth during battery cycling and aging.

25 ENERGY STORAGE↗