Engineering Papers⌕ Search

Engineering topics

Benmore, Chris J.

Publications and source records attributed to Benmore, Chris J..

At least 19 records

AUTOIGNITION DELAY TIMES FOR REFORMATE GAS MIXTURES FROM METHANE GAS ENGINES

Methane slip is a prominent issue in natural gas reciprocating engines that are used in transportation and marine applications. The incomplete combustion that results in methane slip can be resolved with the introduction of hydrogen within the combustion mixture to improve methane oxidation and further enable combustion within the engine crevices where methane has previously remained unreacted. Steam methane reforming (SMR) is a common method used to produce hydrogen and can be used to design an onboard device to reduce methane slip from reciprocating engines. The development of this reformer device requires the validation of high-fidelity chemical kinetic models at the low temperatures of the crevice volumes of these engines. In this work, auto-ignition data is obtained using a shock tube at lean (φ—0.714 or λ—1.4) and stoichiometric (φ, λ = 1) equivalence ratios spanning a temperature range of 1042–1234 K at the 80-bar operating pressure of the test engine. Blends of methane, hydrogen, and reformate products from the SMR reaction are shock-heated in synthetic air, with the ignition delay time measured using an OH* chemiluminescence detector at 310 nm and a CH* detector at 430 nm. The experimental results are compared to several state-of-the-art chemical kinetic mechanisms from the literature. In general, most of the mechanisms show very good agreement with experiments at higher temperatures, with simulation results showing little deviation from experiments at lower temperatures. A sensitivity analysis was conducted, and the results reveal that the reaction H2 + CH3O2 = H + CH3O2H has a very significant role in determining low-temperature ignition delay times (IDTs) of SMR mixtures. These findings provide valuable insights into the chemical kinetics governing methane reformate combustion and contribute to the optimization of onboard reformer designs aimed at mitigating methane slip in natural gas-fueled engines.

Fraze, Matthew↗

Detecting underscreening and generalized Kirkwood transitions in aqueous electrolytes

We establish the connection between the measured small angle x-ray scattering signal and the charge–charge correlations underlying Kirkwood transitions (KTs) in 1:1, 2:1, and 3:1 aqueous electrolytes. These measurements allow us to obtain underscreening lengths for bulk electrolytes independently verified by theory and simulations. Furthermore, we generalize the concept of KTs beyond those theoretically predicted for 1:1 electrolytes, which involves the inverse screening length, a 0 , and the inverse periodicity length, Q 0 . Above the KTs, we find a universal scaling of a 0 ∝ c – $\sqrt{ζ/3}$ and Q 0 ∝ c 1/3 for the studied electrolyte solutions, where ζ is the ionic strength factor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evidence of short chains in liquid sulfur

High energy x-ray pair distribution function measurements show the average coordination number of the first shell in liquid sulfur is 1.86 ± 0.04 across the λ-transition, not precisely 2.0 as widely accepted. This indicates that upon melting, liquid sulfur does not comprise solely of S 8 rings but also possesses a significant number of short chains. Intensities of the pre-peak and first diffraction peak of the x-ray structure factor and third peak height of the pair distribution function all show deviations at the λ-transition temperature T λ , associated with the break-up of S 8 rings and the start of oligomer polymerization. A significant number of non-bonded or loosely bonded “interstitial atoms,” with an average coordination number of 0.20 ± 0.005, are also observed in the so-called “forbidden zone” between the first and second shells upon melting. The number of interstitial atoms is found to decrease to a minimum at the λ-transition, but the majority persist into the high temperature polymerized liquid. Furthermore, the existence of short chains and nearby interstitial atoms represent the two main factors required to initiate the S 8 -ring to chain transition, as proposed by recent molecular dynamics simulations.

Chemical bonding↗

Rigidity‐Driven Structural Isomers in the NaCl–Ga 2 S 3 System: Implications for Energy Storage

Alternative energy sources require the search for innovative materials with promising functionalities. Systems with unusual chemical properties represent an insufficiently explored domain, concealing unexpected features. Using diffraction and Raman spectroscopy over a wide temperature range, supported by first‐principles simulations, a rare phenomenon is unveiled: phase‐dependent chemical interactions between binary components in the NaCl–Ga 2 S 3 system. In this unique occurrence, previously intact binary crystalline species transform upon melting into mixed liquid structural isomers, forming bonds with new partners. The chemical combinatorics appears to be fully reversible for stable crystals and liquids. Despite this, rapidly frozen glasses out of thermodynamic equilibrium remain in a metastable isomeric state, offering remarkable properties, particularly a high room‐temperature Na + conductivity, comparable to the best sodium halide superionic conductors and therefore encouraging for sodium solid‐state batteries and energy applications. A rigidity paradigm is responsible for the observed phenomenon, as the extremely constrained Ga 2 S 3 crystal lattice does not survive viscous flow, breaking up at a short‐range level. The removal of rigidity constraints and dense packing leads to a significant increase in empty space, which is the origin of high sodium diffusivity. Broadly, the rigidity‐driven structural isomerism opens up an inspiring path to the discovery of atypical materials.

25 ENERGY STORAGE↗

The structure of CaO–MgO–Al 2 O 3 –SiO 2 melts and glasses doped with FeO X –NiO

Neutron and x-ray diffraction measurements have been performed on CaO–MgO–Al 2 O 3 –SiO 2 (CMAS) glasses doped with NiO–Fe X O at room temperature, along with x-ray measurements on aerodynamically levitated liquids at ≥2000 K. The disordered structures have been modeled using empirical potential structure refinement to investigate the relation between the aluminosilicate network and the modifying cations. The SiO 4 and AlO 4 tetrahedra are found to have wider Si–O and Al–O bond distance distributions in the glass, and the first Ca–O n coordination shell is highly distorted, redistributing different populations of long and short bonds between the liquid and the glass. The addition of Fe and Ni at low aluminosilicate content increases the number of free oxygens not bonded to AlO 4 or SiO 4 . Mg–O and Fe–O are both found to be predominantly fourfold and fivefold in the liquid and glassy states. Despite these low coordination numbers, their bond angle distributions indicate that they are predominantly in nontetrahedral-type geometries, with ferrous and ferric iron possessing similar coordination environments. The Ca–O and Mg–O average coordination numbers and enthalpies of solution are consistent with their higher reactivity within relatively acidic aluminosilicate melts.

36 MATERIALS SCIENCE↗

Microgravity effects on nonequilibrium melt processing of neodymium titanate: thermophysical properties, atomic structure, glass formation and crystallization

The relationships between materials processing and structure can vary between terrestrial and reduced gravity environments. As one case study, we compare the nonequilibrium melt processing of a rare-earth titanate, nominally 83TiO 2 -17Nd 2 O 3 , and the structure of its glassy and crystalline products. Density and thermal expansion for the liquid, supercooled liquid, and glass are measured over 300–1850 °C using the Electrostatic Levitation Furnace (ELF) in microgravity, and two replicate density measurements were reproducible to within 0.4%. Cooling rates in ELF are 40–110 °C s -1 lower than those in a terrestrial aerodynamic levitator due to the absence of forced convection. X-ray/neutron total scattering and Raman spectroscopy indicate that glasses processed on Earth and in microgravity exhibit similar atomic structures, with only subtle differences that are consistent with compositional variations of ~2 mol. % Nd 2 O 3 . The glass atomic network contains a mixture of corner- and edge-sharing Ti-O polyhedra, and the fraction of edge-sharing arrangements decreases with increasing Nd 2 O 3 content. X-ray tomography and electron microscopy of crystalline products reveal substantial differences in microstructure, grain size, and crystalline phases, which arise from differences in the melt processes.

36 MATERIALS SCIENCE↗

Atomic Structure and Dynamics of Unusual and Wide-Gap Phase-Change Chalcogenides: A GeTe 2 Case

Brain-inspired computing, reconfigurable optical metamaterials, photonic tensor cores, and many other advanced applications require next-generation phase-change materials (PCMs) with better energy efficiency and a wider thermal and spectral range for reliable operations. Germanium ditelluride (GeTe 2 ), with higher thermal stability and a larger bandgap compared to current benchmark PCMs, appears promising for THz metasurfaces and the controlled crystallization of atomically thin 2D materials. Using high-energy X-Ray diffraction supported by first-principles simulation, the atomic structure in semiconducting pulsed laser deposition films and metallic high-temperature liquids is investigated. The results suggest that the structural and chemical metastability of GeTe 2 , leading to disproportionation into GeTe and Te, is related to high internal pressure during a semiconductor–metal transition, presumably occurring in the supercooled melt. Similar phenomena are expected for canonical GeS 2 and GeSe 2 under high temperatures and pressures.

74 ATOMIC AND MOLECULAR PHYSICS↗

Probing lead acetate in solution using X-ray diffraction

Here, for the purpose of water purification involving toxic metal sensing and removal, high energy X-ray diffraction experiments have been performed on lead acetate Pb(Ac) 2 solutions, liquid and amorphous glutathione disulfide (GSSG), and their mixtures. The data have been interpreted using Empirical Potential Structure Refinement and pair distribution function analysis. At the highest concentration of 1 M Pb(Ac) 2 in water, the lead molecules are found to cluster and the second shell in the water structure becomes slightly more ordered as the water molecules become compressed. Liquid and amorphous GSSG are found to hydrogen bond primarily via OH-O interactions, while NH-O bonds are much more distorted. Aqueous solutions of Pb(Ac) 2 + GSSG show the closest Pb-O (carboxyl) and Pb-N (amine) bonds both at a distance of 2.5 ± 0.1 Å at a concentration of 1 M Pb(Ac) 2 in water. At 0.75 M Pb(Ac) 2 in water, strong Pb-S bonds are found at a distance of 2.8 ± 0.1 Å. The implications for lead removal using capacitive deionization are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing Molecular Packing of Amorphous Pharmaceutical Solids Using X-ray Atomic Pair Distribution Function and Solid-State NMR

The structural investigation of amorphous pharmaceuticals is of paramount importance in comprehending their physicochemical stability. However, it has remained a relatively underexplored realm primarily due to the limited availability of high-resolution analytical tools. Here in this study, we utilized the combined power of X-ray pair distribution functions (PDFs) and solid-state nuclear magnetic resonance (ssNMR) techniques to probe the molecular packing of amorphous posaconazole and its amorphous solid dispersion at the molecular level. Leveraging synchrotron X-ray PDF data and employing the empirical potential structure refinement (EPSR) methodology, we unraveled the existence of a rigid conformation and discerned short-range intermolecular C–F contacts within amorphous posaconazole. Encouragingly, our ssNMR 19 F– 13 C distance measurements offered corroborative evidence supporting these findings. Furthermore, employing principal component analysis on the X-ray PDF and ssNMR data sets enabled us to gain invaluable insights into the chemical nature of the intermolecular interactions governing the drug–polymer interplay. These outcomes not only furnish crucial structural insights facilitating the comprehension of the underlying mechanisms governing the physicochemical stability but also underscore the efficacy of synergistically harnessing X-ray PDF and ssNMR techniques, complemented by robust modeling strategies, to achieve a high-resolution exploration of amorphous structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular interactions in short-chain perfluoroalkyl carboxylic acids and aqueous solutions

The presence of short-chain per- and polyfluoroalkyl substances in water poses a major health and environmental challenge. Here, we have performed high-energy small- and wide-angle X-ray scattering measurements on CF 3 [CF 2 ] n COOH (where n = 1, 2, 3 represents the chain length) and their aqueous solutions at 10% mole concentrations to characterize their molecular interactions at the atomic and nanometer length scales. The experimental wide-angle structure factors have been modelled using Empirical Potential Structural Refinement. The oxygen–oxygen partial X-ray pair distribution functions show that the coordination number between the hydroxyl oxygen on the acid and surrounding oxygen water molecules increases significantly with acid chain length, rising from 3.2 for n = 1 to 4.1 for n = 3. The small-angle scattering is dominated by a sharp, high-intensity peak at Q 1 ~ 0.2 Å -1 and a smaller peak at Q 2 = 1.2 Å -1 for n = 3, both of which decrease with decreasing chain length. The Q 2 peak is attributed to groups of adjacent non-bonded acid molecules, and Q 1 has contributions from both correlations between acid molecules and water–water interactions. In all cases, the models show nanoscale aggregation occurs in the form of denser channels of winding hydrogen-bonded chains, approximately 20 water molecules in length, surrounding clusters of acid molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The structure of molten calcium ferrite under various redox conditions

Laser-heated melts based on the 43CaO–57Fe 2 O 3-x eutectic, close to the calcium ferrite (CF) composition, were measured with high-energy X-ray diffraction using aerodynamic levitation over a range of redox states controlled by CO/CO 2 gas atmospheres. The iron–oxygen coordination number was found to rise from 4.4 ± 0.3 at 15% Fe 3+ to 5.3 ± 0.3 at 87% Fe 3+ . Empirical potential structure refinement modelling was used to obtain the ferric and ferrous partial pair distribution functions. It was found that the Fe 2+ iron–oxygen coordination number is consistently approximately 10% higher in CF than in pure iron oxide, while Fe 3+ is essentially identical in all but the most oxygen-rich environments (where it is higher in CF compared with FeO x ). The model also shows calcium octahedra to be the dominant species across all redox environments, although the population of CaO 7 increases with the availability of oxygen at the expense of CaO 4 and CaO 5 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mapping the structural trends in zinc aluminosilicate glasses

The structure of zinc aluminosilicate glasses with the composition (ZnO) x (Al 2 O 3 ) y (SiO 2 ) 1-x-y , where 0 ≤ x < 1, 0 ≤ y < 1, and x + y < 1, was investigated over a wide composition range by combining neutron and high-energy x-ray diffraction with 27 Al magic angle spinning nuclear magnetic resonance spectroscopy. The results were interpreted using an analytical model for the composition-dependent structure in which the zinc ions do not act as network formers. Four-coordinated aluminum atoms were found to be in the majority for all the investigated glasses, with five-coordinated aluminum atoms as the main minority species. Mean Al–O bond distances of 1.764(5) and 1.855(5) Å were obtained for the four- and five-coordinated aluminum atoms, respectively. The coordination environment of zinc was not observed to be invariant. Instead, it is dependent on whether zinc plays a predominantly network-modifying or charge-compensating role and, therefore, varies systematically with the glass composition. The Zn–O coordination number and bond distance were found to be 4.36(9) and 2.00(1) Å, respectively, for the network-modifying role vs 5.96(10) and 2.08(1) Å, respectively, for the charge-compensating role. The more open coordination environment of the charge-compensator is related to an enhanced probability of zinc finding bridging oxygen atoms as nearest-neighbors, reflecting a change in the connectivity of the glass network comprising four-coordinated silicon and aluminum atoms as the alumina content is increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Decoding the Atomic Structure of Ga 2 Te 5 Pulsed Laser Deposition Films for Memory Applications Using Diffraction and First-Principles Simulations

Neuromorphic computing, reconfigurable optical metamaterials that are operational over a wide spectral range, holographic and nonvolatile displays of extremely high resolution, integrated smart photonics, and many other applications need next-generation phase-change materials (PCMs) with better energy efficiency and wider temperature and spectral ranges to increase reliability compared to current flagship PCMs, such as Ge 2 Sb 2 Te 5 or doped Sb 2 Te. Gallium tellurides are favorable compounds to achieve the necessary requirements because of their higher melting and crystallization temperatures, combined with low switching power and fast switching rate. Ga 2 Te 3 and non-stoichiometric alloys appear to be atypical PCMs; they are characterized by regular tetrahedral structures and the absence of metavalent bonding. The sp 3 gallium hybridization in cubic and amorphous Ga 2 Te 3 is also different from conventional p-bonding in flagship PCMs, raising questions about its phase-change mechanism. Furthermore, gallium tellurides exhibit a number of unexpected and highly unusual phenomena, such as nanotectonic compression and viscosity anomalies just above their melting points. Using high-energy X-ray diffraction, supported by first-principles simulations, we will elucidate the atomic structure of amorphous Ga 2 Te 5 PLD films, compare it with the crystal structure of tetragonal gallium pentatelluride, and investigate the electrical, optical, and thermal properties of these two materials to assess their potential for memory applications, among others.

36 MATERIALS SCIENCE↗

Study of beyond nearest-neighbor environment and intermediate-range order in a sodium aluminosilicate geopolymer using Reverse Monte Carlo modeling

A large scale three-dimensional structural model of a geopolymer with an approximate composition of NaAlSi 2 O 6 .5.5H 2 O obtained by Reverse Monte Carlo (RMC) modeling based on experimental high-energy x-ray diffraction is presented for the first time in order to obtain information regarding beyond nearest-neighbor environment and intermediate-range order (IRO). RMC model exhibits a three-dimensional network consisting of randomly cross-linked AlO 4 and SiO 4 tetrahedral units with uniformly distributed Na atoms and H 2 O molecules. The bond angle distributions, i.e. T-O-T, O-T-O and Na-O-Na angles, are somewhat distorted with lower values compared to analogous crystal systems. The origin of the first peak in the structure factor indicating IRO is investigated using the partial structure factors; Na-Na, Si-Na, Al-Si, O-H, and H-H atom pairs are found to be the main contributors. Ring size distribution analysis demonstrates that the structure mainly involves 6-, 7- and 8-membered rings. Finally, the coherence length of these IRO characteristics is ~10.3 Å.

36 MATERIALS SCIENCE↗

Insights on the dissolution of water in an albite melt at high pressures and temperatures from a direct structural analysis

The water dissolution mechanism in silicate melts under high pressures is not well understood. Here we present the first direct structure investigation of a water-saturated albite melt to monitor the interactions between water and the network structure of silicate melt at the molecular level. In situ high-energy X-ray diffraction was carried out on the NaAlSi 3 O 8 -H 2 O system at 800 °C and 300 MPa, at the Advanced Photon Source synchrotron facility. The analysis of the X-ray diffraction data was augmented with classical Molecular Dynamics simulations of a hydrous albite melt, incorporating accurate water-based interactions. The results show that metal–oxygen bond breaking at the bridging sites occurs overwhelmingly at the Si site upon reaction with H 2 O, with subsequent Si–OH bond formation and negligible Al–OH formation. Furthermore, we see no evidence for the dissociation of the Al 3+ ion from the network structure upon breaking of the Si–O bond in the hydrous albite melt. The results also indicate that the Na + ion is an active participant in the modifications of the silicate network structure of the albite melt upon water dissolution at high P–T conditions. We do not find evidence for the Na + ion dissociating from the network structure upon depolymerization and subsequent formation of NaOH complexes. Instead, our results show that the Na + ion persists as a structure modifier with a shift away from Na–BO bonding to an increase in the extent of Na-NBO bonding, in parallel with pronounced depolymerization of the network. Our MD simulations show that the Si–O and Al–O bond lengths are expanded by about 6% in the hydrous albite melt compared to those of the dry melt at high P–T conditions. The changes in the network silicate structure of a hydrous albite melt at high pressure and temperature, as revealed in this study, must be considered in the advancement of water dissolution models of hydrous granitic (or alkali aluminosilicate) melts.

36 MATERIALS SCIENCE↗

In Situ High-Temperature Structural Analysis of High-Entropy Rare-Earth Sesquioxides

High-entropy rare-earth (RE) sesquioxides (RE 2 O 3 ) containing five cations in equimolar amounts have been investigated for a variety of applications, but little is known about their polymorphic behavior and coefficient of thermal expansion. Here, in this work, we evaluate the effect of the average ionic radius (AIR) on the polymorphism of high-entropy RE 2 O 3 . Powder samples of compositions 1 (Lu,Y,Ho,Nd,La) 2 O 3 (AIR = 0.938 Å) and 2 (Gd,Eu,Sm,Nd,La) 2 O 3 (AIR = 0.982 Å) were synthesized via a wet chemical method, and bead samples were prepared for aerodynamic levitation by melting the powders in a copper hearth. Structural transitions were monitored upon cooling from the melt to 1000 °C via in situ X-ray diffraction on aerodynamically levitated samples. The phase evolution was liquid, hexagonal H-type, and monoclinic B-type for composition 1 and liquid, cubic X-type, H-type, and B-type for composition 2. Based on their AIR, the general polymorphic transformations of the high-entropy RE 2 O 3 follow the trend of single-RE RE 2 O 3 , but the transition temperatures differ from those of single-RE RE 2 O 3 . The coefficient of thermal expansion values of the B-type phase of compositions 1 and 2 are similar to those of Gd 2 O 3 and previously published high-entropy RE 2 O 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Revisiting metastable immiscibility in SiO 2 –Al 2 O 3 : Structure and phase separation of supercooled liquids and glasses

Understanding and controlling liquid–liquid phase separation in aluminosilicates is crucial for optimizing glass properties. However, the metastable nature of aluminosilicates’ phase separation has made it difficult to study experimentally, and uncertainty persists regarding the compositional and temperature extents of the miscibility gap. Here, we present new experimental evidence that suggests a consolute temperature between 1440 and 1590°C and endmember compositions of 7 and 62 mol.% Al 2 O 3 for the phase-separated glasses. Using containerless melt processing, deeply supercooled liquids over the 0–60 mol.% Al 2 O 3 range are probed with in situ small- and wide-angle X-ray scattering, which simultaneously reveals changes in nanoscale density heterogeneity and atomic structure. Correlations between phase separation and atomic coordination environments are compared for liquids and glasses. Pair distribution function analysis shows mean O–(Si + Al) coordination increases with Al 2 O 3 content and decreases with temperature.

36 MATERIALS SCIENCE↗