Engineering topics

Benjamin D Jensen

Publications and source records attributed to Benjamin D Jensen.

5 records

NASA NTRS2026

Micromechanical Design of Carbon Nanotube Ribbon Reinforced Polymer Composite Materials

Lightweight materials are an important component of the design of aerospace structures. Carbon nanotube materials have been considered for this purpose due to the strength and stiffness of individual nanotubes, and the commercial availability of bulk formats such as fibers. These fibers can have a ribbon cross section which results in a different design space for their composites relative to traditional reinforcements which have a round cross section. This work applies brick-and-mortar micromechanical models and classical lamination theory with an inverse approach to investigate the design space of these composites. Using this approach, the influences of fiber geometry and axial and transverse mechanical properties are mapped. Finally, a sensitivity study is performed and the relative impacts of ±10% variations in the constituent material and geometric properties are ranked. Lamina axial moduli were found to range from a maximum of 3x to 1x minimum relative to a target quasi-isotropic laminate modulus depending on the anisotropy and shear modulus of the lamina. The fiber targets depended strongly on the fiber volume fraction in the lamina and the fiber axial modulus target was found to range from 4.8x to 3.2x the quasi-isotropic laminate target. The sensitivity analysis found that the largest driver of performance was the volume fraction, followed by the fiber axial modulus. While bio-based brick-and-mortar composites, such as nacre, can benefit from reinforcement aspect ratios above 10, for carbon nanotube ribbon (or carbon fiber)/polymer composites the sensitivity study indicated that the optimal cross-sectional aspect ratio was relatively smaller, potentially less than three.

Micromechanics↗

NASA NTRS2023

Machine Learning to Increase the Quality and Repeatability of 3D Printing - Workflow

The imprecise nature of three-dimensional (3D) printing limits the technology’s use beyond prototyping. For production of end-use parts, such as those for aerospace applications, improvements are needed to enhance quality and repeatability. Much of the difficulty in obtaining high quality printed parts lies in finding optimum printing parameters. Currently, this requires trial and error performed by an expert. Finding the optimum printing parameters is also obfuscated by the variation in optimum parameters throughout the part due to part geometry and printer effects. To allow for locally optimized printing parameters, one can envision a machine learning algorithm that could take in an object, predict the best printing parameters, and communicate these parameters to a printer. With this scenario in mind, we developed a tool that can predict and implement locally optimized printing parameters in 3D printing. This tool consists of elements designed to detect errors in a printed part, predict the probability of local flaws occurring at each point in the part, and select the optimal local parameters for the highest quality part given hardware limitations. The results of this work were highlighted in Advanced Materials Technologies. In this paper, we will discuss in greater depth the workflow and algorithms involved with this tool that were not detailed in the journal publication.

additive manufacturing↗

NASA NTRS2018

Simulating the Effects of Carbon Nanotube Continuity and Interfacial Bonding on Composite Strength and Stiffness

Molecular dynamics simulations of carbon nanotube (CNT) composites, in which the CNTs are continuous across the periodic boundary, overestimate the experimentally measured mechanical properties of CNT composites along the fiber direction. Since the CNTs in these composites are much shorter than the composite dimensions, load must be transferred either directly between CNTs or through the matrix, a mechanism that is absent in simulations of effectively continuous CNTs. In this study, the elastic and fracture properties of high volume fraction discontinuous carbon nanotube/amorphous carbon composite systems were compared to those of otherwise equivalent continuous CNT composites using ReaxFF reactive molecular dynamics simulations. These simulations were used to show how the number of nanotube-matrix interfacial covalent bonds affect composite mechanical properties. Furthermore, the mechanical impact of interfacial bonding was decomposed to reveal its effect on the properties of the CNTs, the interfacial layer of matrix, and the bulk matrix. For the composites with continuous reinforcement, it was found that any degree of interfacial bonding has a negative impact on axial tensile strength and stiffness. This is due to disruption of the structure of the CNTs and interfacial matrix layer by the interfacial bonds. For the discontinuous composites, the modulus was maximized between 4%-7% interfacial bonding and the strength continues to increase up to the highest levels of interfacial bonding studied. Areas of low stress and voids were observed in the simulated discontinuous composites at the ends of the tubes, from which fracture was observed to initiate. Experimental carbon nanotube yarn composites were fabricated and tested. The results were used to illustrate knockdown factors relative to the mechanical performance of the tubes themselves.

Benjamin D Jensen↗

NASA NTRS2017

Modeling Chemical Reactions in Classical Molecular Dynamics Simulations

An algorithm capable of incorporating multi-step reaction mechanisms into atomistic molecular dynamics (MD) simulations using traditional fixed valence force fields is proposed and implemented within the framework of LAMMPS (Large-scale Atomic Molecular Massively Parallel Simulator). This extension, referred to as fix bond/react, enables bonding topology modifications during a running MD simulation using pre- and post-reaction bonding templates to carry out a pre-specified reaction. Candidate reactants are first identified by interatomic separation, followed by the application of a generalized topology matching algorithm to confirm they match the pre-reaction template. This is followed by a topology conversion to match the post-reaction template and a dynamic relaxation to minimize high energy configurations. Two case studies, the condensation polymerization of nylon 6,6 and the formation of a highly-crosslinked epoxy, are simulated to demonstrate the robustness, stability, and speed of the algorithm. Improvements which could increase its utility are discussed.

Jacob R Gissinger↗

NASA NTRSDate not supplied

Carbon Fiber Composite Processing Using Isothermal Resins

To meet future demand for single-aisle composite aircraft production, manufacturing rates are expected to increase by up to six times current production rates. Resin infusion is a manufacturing method that has potential to enable fabrication of structures at the desired rates. However, production cycle times with currently available commercial infusion resins cannot support the rates needed for an estimated 80 aircraft per month. Recently, rapid-curing isothermal resins were developed that can reduce the overall processing time. These resins can be infused, cured, and demolded at a single temperature below 100 °C, thereby eliminating the need for time consuming temperature ramps and shortening the overall cure time. In addition, the low temperatures enable use of low-cost tooling during production. This presentation will discuss the use of resin transfer molding to produce composites with rapid-curing isothermal resins, manufacturing considerations, and performance characteristics of the composites.

John M Gardner↗