Engineering Papers⌕ Search

Engineering topics

Bencze, D. P.

Publications and source records attributed to Bencze, D. P..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Navier-Stokes simulation of flow through a highly contoured subsonic diffuser

The flow through a highly offset subsonic diffuser with cross-sectional profiles that varied from rectangular at the duct entrance to circular at the engine face was numerically simulated. A multizonal approach combined with a two-grid topology was used to represent both the internal and external flowfields, and an implicit, approximately-factored, partially flux-split finite-difference algorithm was used to solve the three-dimensional thin-layer Navier-Stokes equations. The computed static pressures along the inlet wall and total pressures on the engine face were compared with experimental data. In addition, the overall flowfield within the duct was examined in detail. Good agreement is shown between experiment and computations, with the limiting factor being the lack of a reliable turbulence model for internal flow problems.

Chyu, W. J.↗
NASA NTRS1987

Calculation of external-internal flow fields for mixed-compression inlets

Supersonic inlet flows with mixed external-internal compressions were computed using a combined implicit-explicit (Beam-Warming-Steger/MacCormack) method for solving the three-dimensional unsteady, compressible Navier-Stokes equations in conservation form. Numerical calculations were made of various flows related to such inlet operations as the shock-wave intersections, subsonic spillage around the cowl lip, and inlet started versus unstarted conditions. Some of the computed results were compared with wind tunnel data.

Chyu, W. J.↗
NASA NTRS1987

Numerical simulation of three-dimensional supersonic inlet flow fields

Supersonic inlet flows with mixed external-internal compressions of an axisymmetric inlet model were computed using a combined implicit-explicit (Beam-Warming-Steger/MacCormack) method for solving the three-dimensional unsteady, compressible Navier-Stokes equations in conservation form. Numerical calculations were made of various flows typically found in supersonic inlets such as shock-wave intersections, flow spillage around the cowl lip, shock-wave/boundary-layer interactions, control of shock-induced flow separation by means of boundary layer bleed, internal normal (terminal) shocks, and the effects of flow incidence. Computed results were compared with available wind tunnel data.

Kawamura, T.↗
NASA NTRS1986

Calculation of external-internal flow fields for mixed-compression inlets

Supersonic inlet flows with mixed external-internal compressions were computed using a combined implicit-explicit (Beam-Warming-Steger/MacCormack) method for solving the three-dimensional unsteady, compressible Navier-Stokes equations in conservation form. Numerical calculations were made of various flows related to such inlet operations as the shock-wave intersections, subsonic spillage around the cowl lip, and inlet started versus unstarted conditions. Some of the computed results were compared with wind tunnel data.

Chyu, W. J.↗
NASA NTRS1978

Propeller slipstream wing interactions at Mach no. 0.8

Configuration and results of a wind tunnel test of the aerodynamic interactions between propeller slipstream and a supercritical wing at transonic Mach numbers are discussed. The test was conducted over a free-stream Mach number range from 0.7 to 0.84, with the slipstream simulator and the wing-body model installed in the tunnel. The angle of attack and the spanning lift coefficients were varied from 1 to 3 deg and from 0.4 to 0.7 deg respectively, while the slipstream swirl angle was varied from 0 to 11 deg with an upwash on the inboard side of the wing. It was found that at a free-stream Mach number of 0.8 and a lift coefficient of 0.5, incremental drag results for 7 deg of swirl and a slipstream Mach number of 0.87 indicated a penalty equivalent to a 0.024 loss in propeller efficiency, whereas at 11 deg the drag increment was favorable. Swirl had significant effects on the chordwise pressure distributions of the inboard section of the wing within the slipstream. Neither surface nor wake pressures showed signs of significant flow separation induced by the slipstream.

Bencze, D. P.↗
NASA NTRS1978

Estimating maximum instantaneous distortion from inlet total pressure rms measurements

In the present paper, a new mathematical model of inlet turbulence is developed by application of basic fluid dynamics and statistical concepts. The model provides an understanding of the turbulent inlet flow as well as a means of describing the flow in quantitative terms. Specifically, the maximum instantaneous distortion produced by inlet unsteady flow can be estimated by the simple measurement of rms data. Practical application of these techniques leads to a data/acquisition/reduction system that is at least one, and maybe two, orders of magnitude less expensive than conventional methods. Each data point can be reduced in terms of the mean strength of the turbulent vortices. By storing these two parameters (that are representative of the unsteady flow with the steady state information), the maximal instantaneous distortion can be reconstructed for other distortion factors at any time subsequent to the test.

Melick, H. C., Jr.↗
NASA NTRS1977

Advanced turboprop technology development

In order for new short-medium range transports to offer significantly lower operating costs than potential derivatives of current designs using advanced technology, the efficiency improvements of high-speed turboprop propulsion systems may be required. Recent studies indicate that the fuel savings of advanced turboprop aircraft appears to be 10 to 20 percent relative to equivalent technology turbofan aircraft. These fuel savings are certainly large enough to warrant further research to establish the viability of turboprop transport aircraft. The studies have identified the technology requirements in propeller design for high efficiency and low noise, fuselage noise attenuation, propeller and gear box maintenance, and engine-airframe integration. This paper presents a review of present research in each of these areas and describes the future plans for continued development of the technology for advanced turboprop transport aircraft.

Dugan, J. F.↗
NASA NTRS1977

Experimental evaluation of nacelle-airframe interference forces and pressures at Mach numbers of 0.9 to 1.4

Detailed interference force-and-pressure data were obtained on a representative supersonic transport wing-body-nacelle combination at Mach numbers of 0.9 to 1.4. The basic model consisted of a delta wing-body aerodynamic model with a length of 158.0 cm (62.2 in.) and a wingspan of 103.6 cm (40.8 in.) and four independently supported nacelles positioned beneath the model. The experimental program was conducted in the Ames 11- by 11-Foot Wind Tunnel at a constant unit Reynolds number. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass-flow ratio. Under the most favorable conditions, the net interference drag was equal to 50 percent the drag of four isolated nacelles at M = 1.4, 75 percent at M = 1.15, and 144 percent at M = 0.90. The overall interference effects were found to be rather constant over the operating angle-of-attack range of the configuration. The effects of mass-flow ratio on the interference pressure distributions were limited to the lip region of the nacelle and the local wing surface in the immediate vicinity of the nacelle lip. The net change in the measured interference forces resulting from variations in the nacelle mass-flow ratio were found to be quite small.

Bencze, D. P.↗
NASA NTRS1977

Advanced turboprop technology development

The efficiency of high-speed turboprop propulsion systems is considered with emphasis on fuel savings. Specific topics discussed include: (1) high efficiency and low noise of propeller design; (2) fuselage noise attenuation; (3) propeller and gear box maintenance; and (4) engine-airframe integration.

Dugan, J. F.↗
NASA NTRS1976

Wind tunnel investigation of Nacelle-Airframe interference at Mach numbers of 0.9 to 1.4-force data

Detailed interference force and pressure data were obtained on a representative wing-body-nacelle combination at Mach numbers of 0.9 to 1.4. The model consisted of a delta wing-body aerodynamic force model with four independently supported nacelles located beneath the wing-body combination. The model was mounted on a six-component force balance, and the left-hand wing was pressure-instrumented. Each of the two right-hand nacelles was mounted on a six-component force balance housed in the thickness of the nacelle, while each of the left-hand nacelles was pressure-instrumented. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass-flow ratio. Four different configurations were tested to identify various interference forces and pressures on each component; these included tests of the isolated nacelle, the isolated wing-body combination, the four nacelles as a unit, and the total wing-body-nacelle combination. Nacelle axial location, relative to both the wing-body combination and to each other, was the most important variable in determining the net interference among the components.

Bencze, D. P.↗
NASA NTRS1976

Wind tunnel investigation of Nacelle-Airframe interference at Mach numbers of 0.9 to 1.4-pressure data, volume 2

Detailed interference force and pressure data were obtained on a representative wing-body nacelle combination at Mach numbers of 0.9 to 1.4. The model consisted of a delta wing-body aerodynamic force model with four independently supported nacelles located beneath the wing-body combination. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass flow ratio. Four different configurations were tested to identify various interference forces and pressures on each component; these included tests of the isolated nacelle, the isolated wing-body combination, the four nacelles as a unit, and the total wing-body-nacelle combination. Nacelle axial location, relative to both the wing-body combination and to each other, was the most important variable in determining the net interference among the components. The overall interference effects were found to be essentially constant over the operating angle-of-attack range of the configuration, and nearly independent of nacelle mass flow ratio.

Bencze, D. P.↗
NASA NTRS1976

Wind tunnel investigation of nacelle-airframe interference at Mach numbers of 0.9 to 1.4 - pressure data, volume 1

Detailed interference force and pressure data were obtained on a representative wing-body nacelle combination at Mach numbers of 0.9 to 1.4. The model consisted of a delta wing-body aerodynamic force model with four independently supported nacelles located beneath the wing-body combination. The model was mounted on a six component force balance, and the left hand wing was pressure instrumented. Each of the two right hand nacelles was mounted on a six component force balance housed in the thickness of the nacelle, while each of the left hand nacelles was pressure instrumented. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass flow ratio. Nacelle axial location, relative to both the wing-body combination and to each other, was the most important variable in determining the net interference among the components.

Bencze, D. P.↗
NASA NTRS1975

Estimating maximum instantaneous distortion from inlet total pressure rms and PSD measurements

An inexpensive method is developed to determine the extreme values of instantaneous inlet distortion. This method also provides insight into the basic mechanics of unsteady inlet flow and the associated engine reaction. The analysis is based on fundamental fluid dynamics and statistical methods to provide an understanding of the turbulent inlet flow and quantitatively relate the rms level and power spectral density (PSD) function of the measured time variant total pressure fluctuations to the strength and size of the low pressure regions. The most probable extreme value of the instantaneous distortion is then synthesized from this information in conjunction with the steady state distortion. Results of the analysis show the extreme values to be dependent upon the steady state distortion, the measured turbulence rms level and PSD function, the time on point, and the engine response characteristics. Analytical projections of instantaneous distortion are presented and compared with data obtained by a conventional, highly time correlated, 40 probe instantaneous pressure measurement system.

Melick, H. C., Jr.↗
NASA NTRS1973

Possibilities for improved supersonic inlet performance

The results from detailed large-scale inlet tests were examined to assess the penalties, in terms of vehicle cruise range, for boundary-layer bleed, less than ideal engine-face pressure recovery, inlet weight, and external cowl drag. The assessment suggested specific improvements in the design of the inlet system that may increase the range of a typical supersonic transport approximately 6.9%. While no single design improvement can account for a large increase in range, careful attention to each design detail can yield a substantial total improvement. Because of noise considerations, future engines for advanced supersonic transports may be approximately 50% larger than used for the present study, making the effects of improved inlet performance even more important.

Sorensen, N. E.↗
NASA NTRS1972

Nacelle-airframe interference at low supersonic Mach numbers.

The aerodynamic interference between the propulsion system and airframe for a low supersonic transport with wing-mounted nacelles is examined. Both a flowfield analysis and the equivalent body approach were used to predict the interference lift, drag, and pitching moment as functions of nacelle size, shape, and position. The results indicate that the interference lift and pitching moment, as well as drag, must be included in the analysis to properly assess the interference effects. In addition, the performance of the basic wing was found to play an important role in determining the effectiveness of the interference lift in reducing the net installation drag. Based on a conservative prediction, the interference effects can reduce the installed propulsion system drag to 40% of the isolated drag of the nacelles. Furthermore, including the interference effects in the optimization of the engine cycle from a thermodynamic and weight standpoint can result in a considerable reduction in the net propulsion system weight fraction (fuel plus engines) while increasing the optimum engine bypass ratio of a typical transport vehicle.

Bencze, D. P.↗