Engineering Papers⌕ Search

Engineering topics

Bement, L. J.

Publications and source records attributed to Bement, L. J..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Emergency in-flight egress for general aviation aircraft

A NASA program for development of an inflight egress system for the left (pilot) door of general aviation aircraft is described. The pyrotechnic release door was felt to be necessary because of pilot difficulty in reaching the right door when subjected to spin/stall centrifugal effects. A flexible, linear shaped charged of hexanitrostibene II and a lanyard actuated detonator are discussed, along with mock-up tests and instrumentation. The egress system was designed for minimum structural impact, mimimum pilot initiation procedures, low weight, and no egress interference, and to provide sufficient force to blow off the door, have low required maintenance, and high reliability. Results of 68 tests are reviewed, noting the inclusion of a screen to keep glass fragments from spraying the cabin. Certification was achieved, and uses in the F-111 and B-1 aircraft are noted.

Bement, L. J.↗
NASA NTRS1980

Emergency in-flight egress opening for general aviation aircraft

An emergency in-flight egress system was installed in a light general aviation airplane. The airplane had no provision for egress on the left side. To avoid a major structural redesign for a mechanical door, an add on 11.2 kg (24.6 lb) pyrotechnic-actuated system was developed to create an opening in the existing structure. The skin of the airplane was explosively severed around the side window, across a central stringer, and down to the floor, creating an opening of approximately 76 by 76 cm. The severed panel was jettisoned at an initial velocity of approximately 13.7 m/sec. System development included a total of 68 explosive severance tests on aluminum material using small samples, small and full scale flat panel aircraft structural mockups, and an actual aircraft fuselage. These tests proved explosive sizing/severance margins, explosive initiation, explosive product containment, and system dynamics. This technology is applicable to any aircraft of similar construction.

Bement, L. J.↗
NASA NTRS1980

Emergency in-flight egress opening for general aviation aircraft

In support of a stall/spin research program, an emergency in-flight egress system is being installed in a light general aviation airplane. To avoid a major structural redesign for a mechanical door, an add-on 11.2 kg pyrotechnic-actuated system was developed to create an opening in the existing structure. The airplane skin will be explosively severed around the side window, across a central stringer, and down to the floor, creating an opening of approximately 76 by 76 cm. The severed panel will be jettisoned at an initial velocity of approximately 13.7 m/sec. System development included a total of 68 explosive severance tests on aluminum material using small samples, small and full scale flat panel aircraft structural mock-ups, and an actual aircraft fuselage. These tests proved explosive sizing/severance margins, explosive initiation, explosive product containment, and system dynamics.

Bement, L. J.↗
NASA NTRS1979

Confined explosive joining of tubes

Technique uses explosive ribbon to join and seal tubes hermetically while totally confining explosive products, such as smoke, light, and sound. Only click is audible. Process yields joints of the same strengths as parent metal.

Bement, L. J.↗
NASA NTRS1979

Helicopter emergency escape

The three-man Rotor Systems Research Aircraft (RSRA) Emergency Escape System, the first system known to be fully qualified and operational in a rotary wing aircraft, will have two modes of operation: one providing for full in-flight egress, and the other for the severance of the rotor blades for a return to base as a fixed-wing aircraft. This paper describes the escape system's design principles, integration into the aircraft, qualification, and performance.

Bement, L. J.↗
NASA NTRS1979

Helicopter /RSRA/ in-flight escape system - Component qualification

The paper describes the design, development, and qualification approach for the RSRA (Rotor Systems Research Aircraft) system explosive and pyrotechnic components. The approach was based on previous experience and included: (1) the application of good design practice and quality control, (2) a thorough examination of component interfaces through demonstration testing of functional margins, (3) the carrying out of thorough real-world sequential environmental testing, and (4) the operation of environmentally exposed units in subsystem-level tests at temperature, force, and energy limits. Owing largely to this approach, the RSRA became the first helicopter system to contain a fully qualified and operational in-flight escape system.

Bement, L. J.↗
NASA NTRS1978

Totally confined explosive welding

The undesirable by-products of explosive welding are confined and the association noise is reduced by the use of a simple enclosure into which the explosive is placed and in which the explosion occurs. An infrangible enclosure is removably attached to one of the members to be bonded at the point directly opposite the bond area. An explosive is completely confined within the enclosure at a point in close proximity to the member to be bonded and a detonating means is attached to the explosive. The balance of the enclosure, not occupied by explosive, is filled with a shaped material which directs the explosive pressure toward the bond area. A detonator adaptor controls the expansion of the enclosure by the explosive force so that the enclosure at no point experiences a discontinuity in expansion which causes rupture. The use of the technique is practical in the restricted area of a space station.

Bement, L. J.↗
NASA NTRS1978

Rotor Systems Research Aircraft /RSRA/ Emergency Escape System

The three-man Rotor Systems Research Aircraft (RSRA) Emergency Escape System, the first system known to be fully qualified and operational in a rotary wing aircraft, will have two modes of operation: one providing for full in-flight egress, and the other for the severance of the rotor blades for a return to base as a fixed-wing aircraft. This paper describes the escape system's design principles, integration into the aircraft, qualification, and performance.

Bement, L. J.↗
NASA NTRS1977

Protection against explosive blasts

Simple, hinged cover plate is effective against high explosive blasts. Blast energy under cover is transformed into kinetic energy of plate.

Bement, L. J.↗
NASA NTRS1976

Rotor Systems Research Aircraft /RSRA/ canopy explosive severance/fracture

The Rotor Systems Research Aircraft (RSRA), a compound rotor/fixed-wing aircraft, incorporates an emergency escape system for the three crew members; to achieve unobstructed egress, the overhead acrylic canopies of each crew member will be explosively severed and fractured into predictably small, low-mass pieces. A canopy explosive severance/fracture system was developed under this investigation that included the following system design considerations: selection of canopy and explosive materials, determining the acrylic's explosive severance and fracture characteristics, evaluating the effects of installation variables and temperature, determining the most effective explosive patterns, conducting full-scale, flat and double-curvature canopy tests, and evaluating the effects of back-blast of the explosive into the cockpit.

Bement, L. J.↗
NASA NTRS1974

Apparatus for monitoring linear explosive performance

Techniques provide performance monitoring standard for acceptance, lot qualification, and comparison testing of devices. Exhibit high degree of simplicity, accuracy, and reproducibility. Apparatus simultaneously measures explosive pressure stimulus energy, explosive cutting, or rupturing, ability, and detonation propagation rate.

Bement, L. J.↗
NASA NTRS1974

Method of making an explosively welded scarf joint

A method is presented for obtaining a bond joint between thin metal members without the addition of a bonding agent. The method yields bond strengths comparable to the parent metal. The method comprises overlapping the materials at the edges and bonding them by explosive welding while also making use of the explosive force to shape the materials into an essentially planar configuration.

Bement, L. J.↗
NASA NTRS1974

Totally confined explosive welding

A method and associated apparatus for confining the undesirable by-products and limiting noise of explosive welding are discussed. The apparatus consists fo a simple enclosure into which the explosive is placed and within which the explosion occurs. The shape of the enclosure, the placement of the explosive, and the manner in which the enclosure is placed upon the material to be welded determine the force of the explosion transmitted to the proposed bond area. The explosion is totally confined within the enclosure thus reducing the noise level and preventing debris from being strewn about to contaminate the weld area or create personnel hazards.

Bement, L. J.↗
NASA NTRS1973

Development of low-shock pyrotechnic separation nuts

Performance demonstrations and comparisons were made on six flight type pyrotechnic separation nut designs, two of which are standard designs in current use, and four of which were designed to produce low shock on actuation. Although the shock performances of the four low shock designs are considerably lower than the standard designs, some penalties may be incurred in increased volume, weight, or complexity. These nuts, and how they are installed, can significantly influence the pyrotechnic shock created in spacecraft structures. A high response monitoring system has been developed and demonstrated to provide accurate performance comparisons for pyrotechnic separation nuts.

Bement, L. J.↗
NASA NTRS1973

New explosive seam welding concepts

Recently developed techniques provide totally-confined linear explosive seam welding and produce scarf joint with linear explosive seam welding. Linear ribbon explosives are utilized in making narrow, continuous, airtight joints in variety of aluminum alloys, titanium, copper, brass, and stainless steel.

Bement, L. J.↗
NASA NTRS1972

Small-scale explosive seam welding

A unique small scale explosive seam welding technique is reported that has successfully joined a variety of aluminum alloys and alloy combinations in thicknesses to 0.125 inch, as well as titanium in thicknesses to 0.056 inch. The explosively welded joints are less than one-half inch in width and apparently have no long length limitation. The ribbon explosive developed in this study contains very small quantities of explosive encased in a flexible thin lead sheath. The evaluation and demonstration of this welding technique was accomplished in three phases: evaluation and optimization of ten major explosive welding variables, the development of four weld joints, and an applicational analysis which included photomicrographs, pressure integrity tests, vacuum effects, and fabrication of some potentially useful structures in aluminum and titanium.

Bement, L. J.↗