Engineering Papers⌕ Search

Engineering topics

Bell, J. H.

Publications and source records attributed to Bell, J. H..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

PSP Testing at NASA Ames Research Center

Pressure sensitive paints (PSPs) are now used routinely for measuring surface pressures on wind tunnel models at transonic and supersonic Mach numbers. The method utilizes a surface coating containing fluorescent or phosphorescent materials, the brightness of which varies with the local air pressure on the surface. The present paper will summarize PSP activities (in progress and planned) at the NASA Ames Research Center. One of the main accomplishments at NASA Ames has been the development of a PSP measurement system that is production testing capable. This system has been integrated successfully into the large-scale wind tunnel facilities at Ames. There are several problems related to PSP testing which are unique to large-scale wind tunnel testing. The hardware is often difficult to set-up and must operate under harsh conditions (e.g. high pressures and low temperatures). The data acquisition and reduction times need to be kept to a minimum so that the overall wind tunnel productivity is not compromised. The pressure sensitive paints needs to be very robust; the paints must readily adhere to different surfaces with varying geometries and remain functional for long running times. The paint must have well understood, and preferably minimal, temperature sensitivity since fine control of the tunnel temperature is not easily achievable in the larger wind tunnels. In an effort to improve the overall accuracy of the PSP technique, we are currently evaluating some referenced pressure sensitive paints which contain a pressure- independent luminophor in addition to the one which is affected by the surface pressure. The two luminophors are chosen so that their emission wavelengths are somewhat different. Then by taking two 'wind-on' images with either two cameras (with different filters) or one camera with a rotating filter system, the need for 'wind-off' images can be eliminated. The ratio of the two wind-on images accounts for nonuniform lighting and model motion problems (physical movement of the model under aerodynamic loading) are not a concern any more. The paints and data acquisition and reduction software for this type of a PSI system are currently under development and evaluation. Additional information is contained within the original extended abstract.

Bell, J. H.↗
NASA NTRS1995

Pressure-sensitive paint measurements on a supersonic high-sweep oblique wing model

The pressure-sensitive paint method was used in the test of a high-sweep oblique wing model, conducted in the NASA Ames 9- by 7-ft Supersonic Wind Tunnel. Surface pressure data was acquired from both the luminescent paint and conventional pressure taps at Mach numbers between M = 1.6 and 2.0. In addition, schlieren photographs of the outer flow were used to determine the location of shock waves impinging on the model. The results show that the luminescent pressure-sensitive paint can capture both global and fine features of the static surface pressure field. Comparison with conventional pressure tap data shows good agreement between the two techniques, and that the luminescent paint data can be used to make quantitative measurements of the pressure changes over the model surface. The experiment also demonstrates the practical considerations and limitations that arise in the application of this technique under supersonic flow conditions in large-scale facilities, as well as the directions in which future research is necessary in order to make this technique a more practical wind-tunnel testing tool.

McLachlan, B. G.↗
NASA NTRS1995

The Pressure Sensitive Paint Method: An Overview

Pressure sensitive paint (PSP) is a relatively new aerodynamic measurement method with the unique capability of providing a field measurement of pressure over a test surface. This presentation provides an introductory description of this technology based on a review of the open literature. It confines itself to the application of the method to aircraft development wind tunnel testing, at present the primary application area and thus research focus of the method. Described are PSP fundamentals, the various technology elements comprising PSP technology, and current limitations and considerations in applying the technology. Experimental results are presented to illustrate the present capability of the method.

McLachlan, B. G.↗
NASA NTRS1993

Effects of small changes in initial conditions on mixing layer three-dimensionality

The effects of relatively small changes in the initial conditions of the development of the 3D structure of a plane mixing layer originating from laminar boundary layers were experimentally studied. It is found that, while the exact shapes and positions of the streamwise vortex structures are not the same for the two initial conditions, their overall distribution, reorganization, and decay are very similar. The results likely that while some of the specific details of the streamwise vortex structure may be facility-dependent, a relatively strong structure which produces significant three-dimensionality should form in all mixing layers originating from laminar boundary layers. After some initial readjustments, the structure will appear in the form of counterrotating pairs of streamwise vortices which in the mean, grow with the mixing layer and decay in strength. The results also serve to warn that small changes in initial conditions may significantly affect the Reynolds stress distributions in the near field.

Plesniak, M. W.↗
NASA NTRS1993

Boundary layer transition detection by luminescence imaging

In recent experiments we have demonstrated the feasibility of a new approach to boundary layer transition detection. This new approach employs the temperature dependence of certain photoluminescent materials in the form of a surface coating or 'paint' to detect the change in heat transfer characteristics that accompany boundary layer transition. The feasibility experiments were conducted for low subsonic to transonic Mach numbers on two-dimensional airfoil and flat plate configurations. Paint derived transition locations were determined and compared to those obtained from Preston pressure probe measurements. Artificial heating of the models was used to obtain transition temperature signatures suitable for the instrumentation available to us. Initial estimates show, however, that passive kinetic heating at high Mach numbers is a promising alternative.

Mclachlan, B. G.↗
NASA NTRS1992

Flight testing of a luminescent surface pressure sensor

NASA ARC has conducted flight tests of a new type of aerodynamic pressure sensor based on a luminescent surface coating. Flights were conducted at the NASA ARC-Dryden Flight Research Facility. The luminescent pressure sensor is based on a surface coating which, when illuminated with ultraviolet light, emits visible light with an intensity dependent on the local air pressure on the surface. This technique makes it possible to obtain pressure data over the entire surface of an aircraft, as opposed to conventional instrumentation, which can only make measurements at pre-selected points. The objective of the flight tests was to evaluate the effectiveness and practicality of a luminescent pressure sensor in the actual flight environment. A luminescent pressure sensor was installed on a fin, the Flight Test Fixture (FTF), that is attached to the underside of an F-104 aircraft. The response of one particular surface coating was evaluated at low supersonic Mach numbers (M = 1.0-1.6) in order to provide an initial estimate of the sensor's capabilities. This memo describes the test approach, the techniques used, and the pressure sensor's behavior under flight conditions. A direct comparison between data provided by the luminescent pressure sensor and that produced by conventional pressure instrumentation shows that the luminescent sensor can provide quantitative data under flight conditions. However, the test results also show that the sensor has a number of limitations which must be addressed if this technique is to prove useful in the flight environment.

Mclachlan, B. G.↗
NASA NTRS1992

Sensitivity of the structure of untripped mixing layers to small changes in initial conditions

An experimental study was conducted concerning the influence of small changes in initial conditions on the near- and far-field evolution of the three-dimensional structure of a plan mixing layer. A two-stream mixing layer with a velocity ratio of 0.6 was generated with the initial boundary layers on the splitter plate laminar and was nominally two-dimensional. The initial conditions were changed slightly by interchanging the high- and low-speed sides of the wind tunnel, while maintaining the same velocities, and hence velocity ratio. This resulted in small changes in the initial boundary layer properties, and the perturbations present in the boundary layers were interchanged between the high- and low-speed sides for the two cases. The results indicate that, even with this relatively minor change in initial conditions, the near-field regions of the two cases differ significantly. The peak Reynolds stress levels in the near-field differ by up to 100 percent, and this is attributed to a difference in the location of the initial spanwise vortex roll-up. In addition, the positions and shapes of the individual streamwise vortical structures differ for the two cases, although the overall structures differ for the two cases, although the overall qualitative description of these structures is comparable. The subsequent reorganization and decay of the streamwise vortical structures is very similar for the two cases. As a result, in the far field, both mixing layers achieve similar structure, yielding comparable growth rates, Reynolds stress, distribution, and spectral content.

Plesniak, M. W.↗
NASA NTRS1991

Effect of initial conditions on secondary vortex structure in mixing layers

An experimental research project aimed at obtaining quantitative data on the behavior of the secondary vortex structure in a turbulent mixing layer at moderate Reynolds numbers (Re(sub delta) = 2.9 x 10(exp 4)) is discussed. This project was terminated before all the contemplated measurements could be made, and data were obtained only on the spatially stationary part of the secondary structure. Nonetheless, these data reveal some interesting facets of mixing layer behavior which are discussed.

Bell, J. H.↗
NASA NTRS1991

Effects of initial spanwise perturbations and three-dimensionality in a plane mixing layer

An experimental study concerning the influence of small changaes in initial conditions on the near- and far-field evolution of the th ree-dimensional structure in a plane mixing layer has been conducted. A two-stream mixing layer with a velocity ratio of 0.6 was generated with the initial boundary layers laminar and nominally two-dimensional. The initial conditions were changed slightly by interchanging the high- and low-speed sides of the wind tunnel, while maintaining the same velocity ratio. The results indicate that, even with this minor change in initial conditions, the near-field regions of the two cases differ significantly, with the peak Reynolds stress levels varying by up to 100 percent. In addition, the distribution of the individual streamwise vortical structures differs in intensity and position for the two cases, although the overall qualitative description is comparable.

Plesniak, M. W.↗
NASA NTRS1990

An experimental study of secondary vortex structure in mixing layers

This report covers the first eight months of an experimental research project on the secondary vortex structure in plane mixing layers. The aim of the project is to obtain quantitative data on the behavior of the secondary structure in a turbulent mixing layer at reasonable reynolds numbers (Re(sub delta(sub w)) approx. 50,000). In particular, we hope to resolve the questions of how the scale of the secondary vortex structure changes with the scale of the mixing layer, and whether the structures are fixed in space, or whether they 'meander' in the spanwise direction.

Bell, J. H.↗
NASA NTRS1987

Comparison of experimental and computational techniques for plane mixing layers

In this paper, results from two experimental and two computational investigations of plane turbulent mixing layers are presented and compared. The experimental results include flow visualization data using the smoke laser technique and mean flow and turbulence measurements obtained with hot X-wires and a two-component LDV. Reasonably good agreement is found among these techniques, at least for turbulence quantities up to second order. Reynolds-averaged computations are successful at capturing the complete evolution of the mixing layer, including wake effects in the near field and approach to self-preservation in the far field. The two-dimensional vortex method shows excellent qualitative and quantitative agreement with measured data for the forced mixing layer. For the unforced layer, the results seem to indicate that a three-dimensional computation may be necessary.

Mehta, R. D.↗
NASA NTRS1986

A 3-component laser-Doppler velocimeter data acquisition and reduction system

This report describes a laser Doppler velocimeter capable of measuring all three components of velocity simultaneously in low-speed flows. All the mean velocities, Reynolds stresses, and higher-order products can then be evaluated. The approach followed is to split one of the colors used in a 2-D system, thus creating a third set of beams which is then focused in the flow from an off-axis direction. The third velocity component is computed from the known geometry of the system. In this report, the laser optical hardware and the data acquisition electronics are described in detail. In addition, full operating procedures and listings of the software (written in BASIC and assembly languages) are also included. Some typical measurements obtained with this system in a vortex/mixing layer interaction are presented and compared directly to those obtained with a cross-wire system.

Rodman, L. C.↗
NASA NTRS1985

A 3-component laser-Doppler velocimeter data acquisition and reduction system

A laser doppler velocimeter capable of measuring all three components of velocity simultaneously in low-speed flows is described. All the mean velocities, Reynolds stresses, and higher-order products can be evaluated. The approach followed is to split one of the two colors used in a 2-D system, thus creating a third set of beams which is then focused in the flow from an off-axis direction. The third velocity component is computed from the known geometry of the system. The laser optical hardware and the data acquisition electronics are described in detail. In addition, full operating procedures and listings of the software (written in BASIC and ASSEMBLY languages) are also included. Some typical measurements obtained with this system in a vortex/mixing layer interaction are presented and compared directly to those obtained with a cross-wire system.

Rodman, L. C.↗
NASA NTRS1985

Aspects of the design and performance of a 3-component LDV system

A conventional two color, two component Laser Doppler Velocimeter (LDV) has been converted into one capable of measuring all three components of velocity simultaneously in low-speed flows. All the Reynolds stresses and higher-order products can then be evaluated. The approach followed is to split one of the two colors and to focus a third pair of beams from an off axis direction. The third velocity component is computed from the known geometry of the system. This paper contains details of the system design with emphasis on the additional problems that are encountered through the introduction of the third component. Some preliminary measurements obtained in a vortex/mixing layer interaction are presented and compared directly with those obtained with a cross-wire system.

Bell, J. H.↗