Engineering Papers⌕ Search

Engineering topics

Baylor, Larry

Publications and source records attributed to Baylor, Larry.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of breech geometry and propellant flow on the release of large pellets for the ITER disruption mitigation system

Studies have been performed on the release mechanism for large pellets using high pressure gas in a shattered pellet injector. Typically, pellets are dislodged from the cryogenic surface and accelerated down a barrel using high pressure gas delivered by a fast-acting propellant valve. The pellets impact an angled surface which shatters the pellet into many small fragments before entering the plasma. This technique was initially demonstrated on DIII-D (Commaux et al 2016 Nucl. Fusion 56 046007) and is now deployed on JET, KSTAR, ASDEX-Upgrade, and other tokamaks around the world in support of ITER's disruption mitigation system design and physics basis. The large hydrogen, 28.5 mm diameter, 2 length-to-diameter ratio, pellets foreseen for ITER SPI operation have low material strength and low heat of sublimation, which cause the pellets to be fragile and highly reactive to the impact of warm propellant gas. Due to the size of the pellets, significantly more propellant gas is required to dislodge and accelerate them. This creates a potentially significant propellant gas removal issue as 2–6 bar-L of gas is expected to be required for release and speed control. The research presented in this paper is an in-depth exploration of the parameters that are keys to reliable pellet release and speed control. Computational fluid dynamics (CFD) modeling of propellant flows through various breech designs was conducted to determine the force generated on the back surface of a pellet. These simulations assumed the use of the ORNL designed flyer plate valve. CFD modeling combined with experimental measurements provide adequate insight to determine a path to an optimal valve and breech design for ITER SPI pellet release and speed control while minimizing propellant gas usage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Design and Testing of a Prototype Eddy Current Actuated Valve for the ITER Shattered Pellet Injection System

Reliably mitigating disruptions is essential for ITER to meet its long-term operational research plan without damage to the in-vessel components. Currently, the shattered pellet injection (SPI) technique is the most effective radiator of thermal energy and has been chosen for the baseline disruption mitigation system (DMS) for ITER. The SPI process uses cryogenic temperatures to desublimate material into the barrel of a pipe gun forming a solid cylindrical pellet. Pellets for ITER will initially be hydrogen and hydrogen-neon mixtures. Once formed, pellets are dislodged and accelerated using high-pressure gas (40-60 bar) delivered by a fast-opening valve. The solenoid valves currently used for SPI experiments will not operate in an ITER environment due to the large background magnetic field. An ITER prototype fast-opening valve, called a flyer plate valve (FPV), has been designed and has undergone a wide range of testing. The FPV operates by pulsing current through a pancake coil that is closely coupled with a ``flyer plate.'' The flyer plate is an aluminum plate in which eddy currents are generated creating a repulsive force from the pancake coil. The force generated in the flyer plate rapidly lifts the valve tip off the seat and delivers a pulse of gas to the rear of the pellet, breaking it free from the barrel and accelerating the pellet downstream to its intended target. The design of the valve has been iterated on over the lifetime of this project, as the DMS for ITER shifted from massive gas injection (MGI) to SPI. The most recent design has been tested, and operational ranges have been mapped. The valve must survive 3000+ cycles in an ITER-like magnetic field. The principal functional requirement of this valve is to reliably dislodge and accelerate hydrogen (or H-Ne mixture) pellets into ITER. The valve was mated with an ITER SPI test stand and has been shown to be capable of launching pellets reliably. The valve and power supply design will be discussed in this article, along with the various testing setups used to determine the feasibility of this valve for use on ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Recent progress in shattered pellet injection technology in support of the ITER disruption mitigation system*

Shattered pellet injection (SPI) has been selected as the baseline technology for the disruption mitigation (DM) system for ITER. Typical SPI utilizes cryogenic cooling to desublimate low pressure (<100 mbar) gases onto a cold zone within a pipe gun barrel, forming a cylindrical pellet. Pellets are dislodged from the barrel and accelerated using either a gas driven mechanical punch or high-pressure light-gas delivered by a fast-opening valve. SPI technology developed at Oak Ridge National Laboratory is currently deployed and operational on DIII-D, JET, and KSTAR. These SPI systems are used in experiments for physics scaling to ITER thermal mitigation and runaway electron dissipation/avoidance. The pellet sizes used for these machines are in the range of 4 to 12.5 mm in diameter with length to diameter ratios (L/D) of ~1.5. The current plan for ITER SPI is to utilize pellets that are 28.5 mm in diameter with an L/D of ~2. Furthermore, the large pellet sizes, high steady-state magnetic fields, and limitations of operating in a radiation environment render much of the current technology unusable. In addition to technology improvements, a deeper understanding of pellet material properties, formation, and release is being developed for implementation in future SPI designs, specifically ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Shear Strength and Release of Large Cryogenic Pellets from the Barrel of a Shattered Pellet Injector for Disruption Mitigation

Shattered pellet injection (SPI) has been chosen as the baseline disruption mitigation system on ITER due to its ability to rapidly inject material deep into the plasma to greatly increase the plasma density and radiate the thermal energy. SPI utilizes a mechanical punch or high-pressure gas to release and accelerate a pellet that has been cryogenically desublimated in the barrel of a pipe gun. Various material injection combinations could possibly be implemented during different phases of a disruption event to radiate plasma energy, reduce electromagnetic loads on machine components, avoid the formation of runaway electrons, or to dissipate runaway electrons that form. Each injection phase could possibly utilize combinations of deuterium, neon, or argon. In this paper we outline experimental measurements of pellet material shear strength at SPI operating temperatures to understand the force needed to release SPI pellets. Deuterium, neon, argon, and deuterium-neon mixture pellets with diameters of 8.5, 12.5, and 15.7 mm are formed at a range of relevant gas pressures and temperatures and dislodged from the cold zone with a slow-moving piston driven by a motor. The slow-moving piston is kept above the triple point temperature of the material while the pellet is forming, then cooled to below the triple point temperature before contacting the pellet to minimize any thermal conduction to the pellet. The piston incorporates a load cell to measure the force applied when the pellet breaks away from the cold zone in the barrel.The ability of the gas and punch methods to exceed the shear strength of the studied pellet materials for release has been analyzed. High pressure gas delivered by fast opening valves produce pressure shock to the pellet due to supersonic expansion of the propellant gas. Pressure (and therefore, force) oscillations are present due to transverse density propagation throughout the breech volume. Mechanical punches deliver an impact force through a high-kinetic energy impact. The effect of the mechanical shock on the pellet has been explored and will be presented in this paper. Scaling to larger ITER size SPI pellets will be described.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Methods to determine the radiated power in SPI-mitigated disruptions in JET

Here we present techniques for evaluating the radiated power in JET disruptions. Disrupting plasmas are shown to have non-axisymmetric radiation profiles, motivating the re-evaluation of the standard techniques for calculating the total radiated power at JET using bolometry. Four single-channel bolometers at different toroidal locations are exploited to quantify the radiation asymmetry. Toroidal radiation peaking factors integrated over the entire disruption of up to 1.5 have been observed when varying the quantity of neon in pellets used in disruptions mitigated by shattered pellet injection. Using synthetic bolometer diagnostics developed with the Cherab spectroscopy modeling framework, we can estimate the systematic error on total power calculations for relevant radiation profiles and improve estimates of the total radiated power. We show that the component of the systematic error on the total power due to the poloidal radiation profile can be reduced from 70% to 10% with suitable assumptions about the structure of the poloidal profile.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Spatially dependent modeling and simulation of runaway electron mitigation in DIII-D

New simulations with the Kinetic Orbit Runaway electron (RE) Code (KORC) show RE deconfinement losses to the wall during plasma scrape off are the primary current dissipation mechanism in DIII-D experiments with high-Z impurity injection, and not collisional slowing down. The majority of simulations also exhibit an increase in the RE beam energy due to acceleration by the induced toroidal electric field, even while the RE beam current is decreasing. In this study, KORC integrates RE orbits using the relativistic guiding center equations of motion and incorporates time-sequenced, experimental reconstructions of the magnetic and electric fields and line integrated electron density to construct spatiotemporal models of electron and partially ionized impurity transport in the companion plasma. Comparisons of experimental current evolution and KORC results demonstrate the importance of including Coulomb collisions with partially ionized impurity physics, initial RE energy, pitch angle, and spatial distributions, and spatiotemporal electron and partially ionized impurity transport. The research presented here provides an initial quantification of the efficacy of RE mitigation via injected impurities and identification of the critical role played by loss of confinement due to plasma scrape off on the inner wall as compared to the relatively slow collisional damping.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Injection of multiple shattered pellets for disruption mitigation in DIII-D

Plasma shutdown experiments in DIII-D have injected multiple shattered pellets at different toroidal locations for the first time, as is planned for the ITER disruption mitigation system. Systematically varying the relative timing of the two pellets suggests that simultaneously injected pellets may influence the assimilation of each other, altering the resulting disruption characteristics compared to a single pellet injecting similar neon quantities. Thermal quench (TQ) radiation measured near the injection location is reduced with the dual pellets, contrary to TQ radiation measured away from the injection ports, which does not show a clear difference between single or dual pellet injections. The mitigation of other disruption loads, such as the current quench (CQ) duration and divertor heat loads, decrease when the pellets enter the plasma simultaneously compared to single shattered pellet injections with similar neon quantities. This similar reduction in mitigation of CQ and conductive loads is consistent with the observed reduction in total TQ radiation. The time between initial pellet injection and the end of the TQ is shorter when both pellets are injected simultaneously compared to a single pellet. This lower cooling duration may limit the amount of the neon assimilated by the plasma prior to the end of the TQ, consistent with the observed reduction in radiation. The injected impurities spread primarily in the parallel direction, away from the source at the injection location. The addition of two shattered pellet injectors shows that the initial poloidal radiation is spread out into two distinct regions, cooling multiple flux tubes simultaneously, which may induce global MHD instabilities more rapidly than a single flux tube of impurities leading to a shorter cooling duration. The electron density increased by approximately a factor of two with the addition of multiple pellets, but is highly sensitive to the time between injections. Here, a maximum density increase is found when both pellets arrive at the plasma prior to the start of the TQ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Study of argon assimilation into the post-disruption runaway electron plateau in DIII-D and comparison with a 1D diffusion model

The assimilation of argon injected into post-disruption runaway electron (RE) plateaus is studied and compared to the vertical loss rate for vertically unstable RE plateaus. A 1D diffusion model is developed to include neutral diffusion and ionization and is used to help in data interpretation. It is found that the radial mixing time scale of argon ions (~0.05 s) is comparable to the vertical loss timescale. Neutral argon becomes the dominant Ar species in the RE plateau for large Ar numbers (> 3 x 10 21 ); at the same time the neutral Ar diffusivity decreases due to plasma cooling, causing a saturation in the assimilation of injected Ar on the vertical loss time scale. Injection of Ar into vertically unstable RE plateaus in DIII-D does increase the vertical loss rate, as predicted by previous modeling of ITER. Furthermore, there is a decreasing trend in RE current at the wall strike as the Ar quantity is turned up or as the Ar is injected earlier, indicating a decrease in RE energy deposited to the wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Utilizing M3D-C1 to understand triggering of ELMs in DIII-D pellet pacing experiments

M3D-C1, a code for solving the linear and non-linear extended-MHD equations in toroidal geometry, is used to model pellet ELM triggering in DIII-D ITER-like plasmas. Understanding of the physical mechanisms of ELM triggering and improved modeling are required for condent extrapolation to ITER and beyond. M3D-C1 results run in linear 2D mode show that the localized perturbation is due to the pellet destabilizing peeling-ballooning modes. Calculations of linear peeling-ballooning stability as a function of pellet size suggest that a 2D pellet density ring underestimates the eects of the pellet.

Diem, Stephanie↗
DOE OSTI2019

Shattered pellet injection technology design and characterization for disruption mitigation experiments

The technology to form and shoot high-Z cryogenic solid pellets mixed with deuterium using a gas gun that are shattered upon injection into a plasma has been developed at Oak Ridge National Laboratory for mitigating disruptions. This technology has been selected as the basis for the baseline disruption mitigation system on ITER. The development of shattered pellet injection systems has progressed to be able to accelerate large pellets of pure argon and neon with or without including deuterium. Impact studies have been carried out at shallow angles to determine funnel performance in guiding pellets from multiple barrels into a common injection line and across pumping breaks. The characterization of the shattered spray has also progressed with fragment size measurements as a function of pellet speed showing a strong inverse relationship. Results of these studies are reported with implications for applications on existing and future tokamak devices.

Baylor, Larry↗
DOE OSTI2017

Gas Gun Model and Comparison to Experimental Performance of Pipe Guns Operating with Light Propellant Gases and Large Cryogenic Pellets

Injection of multiple large (~10 to 30 mm diameter) shattered pellets into ITER plasmas is presently part of the scheme planned to mitigate the deleterious effects of disruptions on the vessel components. To help in the design and optimize performance of the pellet injectors for this application, a model referred to as “the gas gun simulator” has been developed and benchmarked against experimental data. The computer code simulator is a Java program that models the gas-dynamics characteristics of a single-stage gas gun. Following a stepwise approach, the code utilizes a variety of input parameters to incrementally simulate and analyze the dynamics of the gun as the projectile is launched down the barrel. Using input data, the model can calculate gun performance based on physical characteristics, such as propellant-gas and fast-valve properties, barrel geometry, and pellet mass. Although the model is fundamentally generic, the present version is configured to accommodate cryogenic pellets composed of H2, D2, Ne, Ar, and mixtures of them and light propellant gases (H2, D2, and He). The pellets are solidified in situ in pipe guns that consist of stainless steel tubes and fast-acting valves that provide the propellant gas for pellet acceleration (to speeds ~200 to 700 m/s). The pellet speed is the key parameter in determining the response time of a shattered pellet system to a plasma disruption event. The calculated speeds from the code simulations of experiments were typically in excellent agreement with the measured values. With the gas gun simulator validated for many test shots and over a wide range of physical and operating parameters, it is a valuable tool for optimization of the injector design, including the fast valve design (orifice size and volume) for any operating pressure (~40 bar expected for the ITER application) and barrel length for any pellet size (mass, diameter, and length). Key design parameters and proposed values for the pellet injectors for the ITER disruption mitigation systems are discussed.

Combs, Stephen Kirk↗
DOE OSTI2017

DESIGN AND COMMISSIONING OF A THREE-BARREL SHATTERED PELLET INJECTOR FOR DIII-D DISRUPTION MITIGATION STUDIES

Disruptions are sudden unplanned terminations of tokamak plasmas that can lead to high thermal loads and runaway electrons (RE). Unmitigated disruptions in ITER are predicted to dissipate hundreds of MJ of thermal energy and generate multi-MeV runaway electrons. This intense heat and energetic particle beams can cause localized melting of the plasma facing components. Reliable and fast acting disruption mitigation (DM) techniques are therefore a critical requirement for ITER to safeguard the machine from damage. The proven method for DM centers on injecting a large quantity of impurity particles into the plasma to quickly increase density and radiate the thermal energy to mitigate thermal effects. Additionally, if the particle injection can achieve a critical density, it can create collisional drag which suppresses the formation of REs. The particle injection methods attempted have been shell pellet injection, massive gas injection, and shattered pellet injection (SPI). The SPI technique has been successfully used on DIII-D [1] to study thermal mitigation using a single-barrel SPI system that can more efficiently reach the critical density required for successful disruption mitigation than the other injection approaches. Recently, a new three-barrel second SPI (SPI-II) system has been developed for use on DIII-D to study injection effects from multiple toroidal locations and pellet timing. The SPI-II system is a liquid helium cooled pipe gun that has two 7 mm and one 8.5 mm pellet sizes. The pellet sizes are determined by the inner diameter of the pipe gun barrels which can easily be changed for different pellet sizes. The three pellets can be formed and fired individually or simultaneously. The SPI-II has provisions for making and firing pure species pellets with deuterium, neon, or argon and also deuterium layered pellets with a core of neon. The pellets are fired into a bent tube near the plasma edge which shatters them from the impact. This paper will describe the design and commissioning of the SPI-II system. Measured pellet speeds and shattered pellet fragment sizes will be reported.

Meitner, Steven↗
DOE OSTI2017

Tritium Aspects of Fueling and Exhaust Pumping in Magnetic Fusion Energy

Magnetically confined fusion plasmas generate energy from deuterium-tritium (DT) fusion reactions that produce energetic 3.5 MeV alpha particles and 14 MeV neutrons. Since the DT fusion reaction rate is a strong function of plasma density, an efficient fueling source is needed to maintain high plasma density in such systems. Energetic ions in fusion plasmas are able to escape the confining magnetic fields at a much higher rate than the fusion reactions occur, thus dictating the fueling rate needed. These lost ions become neutralized and need to be pumped away as exhaust gas to be reinjected into the plasma as fuel atoms.The technology to fuel and pump fusion plasmas has to be inherently compatible with the tritium fuel. An ideal holistic solution would couple the pumping and fueling such that the pump exhaust is directly fed back into pellet formation without including impurity gases. This would greatly reduce the processing needs for the exhaust. Concepts to accomplish this are discussed along with the fueling and pumping needs for a DT fusion reactor.

Baylor, Larry↗
DOE OSTI2017

Tritium Challenges and Plans for ITER Pellet Fueling and Disruption Mitigation Systems

ITER will use a Pellet Injection System (PIS) for supplying deuterium-tritium (D-T) fuel to the fusion plasma and a Shattered Pellet Injection (SPI) system for rapidly injecting impurities (argon or neon mixed with deuterium) as solidified pellets into the plasma for the purpose of mitigating the harmful effects of plasma disruptions as part of a Disruption Mitigation System (DMS). Both systems are being designed to handle significant amounts of tritium in the process streams and are exposed to similar environmental conditions during operation, including exposure to gamma and neutron radiation and significant magnetic fields. Multiple barriers to prevent the potential release of the tritium inventory into the environment are included in the designs. The unique environmental conditions present some challenges and are currently being addressed during the design phase.

Lyttle, Mark↗
DOE OSTI2016

Pellet Injection Technology and Application to Mitigate Transient Events on ITER

The technology to form and accelerate cryogenically solidified pellets of hydrogen isotopes has long been under development for fueling fusion plasmas. Injectors are being designed to provide this capability for fueling ITER with DT pellets injected from the inner wall. In addition to this fueling application, the pellet technology is being further developed for ITER to mitigate transient heat fluxes and energetic particle impacts from disruptions and edge localized modes (ELMs). Large shattered impurity pellets have been found to effectively mitigate disruptions and small pellets of deuterium have been used to trigger on demand rapid small ELMs to limit the transient heat flux damage from otherwise large naturally occurring ELMs. Both of these technologies are being implemented for ITER.

Baylor, Larry↗