Engineering Papers⌕ Search

Engineering topics

Batterson, J. G.

Publications and source records attributed to Batterson, J. G..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Determination of longitudinal aerodynamic derivatives using flight data from an icing research aircraft

A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivatives were adequately determined by the flight test procedure and the MSR analysis method discussed herein.

Ranaudo, R. J.↗
NASA NTRS1989

Determination of longitudinal aerodynamic derivatives using flight data from an icing research aircraft

A flight test was performed with the NASA Lewis Research Center's DH-6 icing research aircraft. The purpose was to employ a flight test procedure and data analysis method, to determine the accuracy with which the effects of ice on aircraft stability and control could be measured. For simplicity, flight testing was restricted to the short period longitudinal mode. Two flights were flown in a clean (baseline) configuration, and two flights were flown with simulated horizontal tail ice. Forty-five repeat doublet maneuvers were performed in each of four test configurations, at a given trim speed, to determine the ensemble variation of the estimated stability and control derivatives. Additional maneuvers were also performed in each configuration, to determine the variation in the longitudinal derivative estimates over a wide range of trim speeds. Stability and control derivatives were estimated by a Modified Stepwise Regression (MSR) technique. A measure of the confidence in the derivative estimates was obtained by comparing the standard error for the ensemble of repeat maneuvers, to the average of the estimated standard errors predicted by the MSR program. A multiplicative relationship was determined between the ensemble standard error, and the averaged program standard errors. In addition, a 95 percent confidence interval analysis was performed for the elevator effectiveness estimates, C sub m sub delta e. This analysis identified the speed range where changes in C sub m sub delta e could be attributed to icing effects. The magnitude of icing effects on the derivative estimates were strongly dependent on flight speed and aircraft wing flap configuration. With wing flaps up, the estimated derivatives were degraded most at lower speeds corresponding to that configuration. With wing flaps extended to 10 degrees, the estimated derivatives were degraded most at the higher corresponding speeds. The effects of icing on the changes in longitudinal stability and control derivat

Ranaudo, R. J.↗
NASA NTRS1986

Lateral and longitudinal aerodynamic stability and control parameters of the basic vortex flap research aircraft as determined from flight test data

The aerodynamics of the basic F-106B were determined at selected points in the flight envelope. The test aircraft and flight procedures were presented. Aircraft instrumentation and the data system were discussed. The parameter extraction procedure was presented along with a discussion of the test flight results. The results were used to predict the aircraft motions for maneuvers that were not used to determine the vehicle aerodynamics. The control inputs used to maneuver the aircraft to get data for the determination of the aerodynamic parameters were discussed in the flight test procedures. The results from the current flight tests were compared with the results from wind tunnel test of the basic F-106B.

Suit, W. T.↗
NASA NTRS1986

STEP and STEPSPL: Computer programs for aerodynamic model structure determination and parameter estimation

The successful parametric modeling of the aerodynamics for an airplane operating at high angles of attack or sideslip is performed in two phases. First the aerodynamic model structure must be determined and second the associated aerodynamic parameters (stability and control derivatives) must be estimated for that model. The purpose of this paper is to document two versions of a stepwise regression computer program which were developed for the determination of airplane aerodynamic model structure and to provide two examples of their use on computer generated data. References are provided for the application of the programs to real flight data. The two computer programs that are the subject of this report, STEP and STEPSPL, are written in FORTRAN IV (ANSI l966) compatible with a CDC FTN4 compiler. Both programs are adaptations of a standard forward stepwise regression algorithm. The purpose of the adaptation is to facilitate the selection of a adequate mathematical model of the aerodynamic force and moment coefficients of an airplane from flight test data. The major difference between STEP and STEPSPL is in the basis for the model. The basis for the model in STEP is the standard polynomial Taylor's series expansion of the aerodynamic function about some steady-state trim condition. Program STEPSPL utilizes a set of spline basis functions.

Batterson, J. G.↗
NASA NTRS1985

On the identification of a highly augmented airplane

The results of applying linear least squares and maximum likelihood estimation procedures to flight data from the AFTI/F-16 airplane are presented. Data from two flight control system modes are analyzed. It is shown that though a simple aerodynamic model structure is adequate for the simple mode, a more complicated model is necessary to adequately describe the highly augmented mode. The effect of augmentation of roll control is shown to be visible in the control parameters.

Batterson, J. G.↗
NASA NTRS1985

Estimation of transport airplane aerodynamics using multiple stepwise regression

This paper presents an application of multiple stepwise regression to the flight test data of a typical transport airplane. The flight test data was carefully preprocessed to eliminate aliasing, time skews and high frequency noise. The data consisted both of basic certification maneuvers, such as wind-up-turns and maneuvers suitable for parameter estimation, such as responses to elevator pulses and doublets. It is shown that the results of multiple stepwise regression techniques compare favorably with the results obtained from maximum likelihood estimation. Finally, it is concluded that multiple stepwise regression could be a fast economical way to estimate transport airplane aerodynamics.

Keskar, D. A.↗
NASA NTRS1984

Applications of model structure determination to flight test data

Several statistical and information criteria need to be considered when selecting an adequate model. Incorrect stability and control derivates result from inadequate aerodynamic model structure. Stepwise regression is used to determine the structure for an adequate model. Flight data which covers a nonlinear aerodynamic model range may be analyzed as a single data set or partitioned into several distinct sets. Stepwise regression for model structure detemination and parameter estimation was successfully applied to three aircraft types (single engine general aviation, unaugmented modern jet fighter, jet transport).

Batterson, J. G.↗
NASA NTRS1984

A preliminary analysis of flight data from the AFTI/F-16 airplane

Flight test data from the AFTI/F-16 airplane are analyzed. Two flight control system modes (Independent Backup Unit and Standard Normal Mode) are considered. Estimated stability and control derivatives are compared with values from the wind tunnel and F-16A flight tests. Modeling difficulties are shown to arise due to the near-neutral static stability of the airplane and the number of coordinated control surface movements commanded in the Standard Normal Mode.

Batterson, J. G.↗
NASA NTRS1984

Estimated low-speed aerodynamic parameters of an advanced fighter from flight and wind tunnel data

A procedure for determination of aerodynamic model structure and estimation of aerodynamic parameters is applied to data from a modern fighter operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, postulated models for airplane aerodynamic coefficients and flight data analysis. The results presented contain only a small number of selected longitudinal and lateral parameters. These parameters were obtained from various maneuvers and subsets of joined data from several flights. The estimated parameters are in good agreement with the wind tunnel measurements. The resulting aerodynamic model equations seem to be satisfactory for the prediction of airplane motion.

Klein, V.↗
NASA NTRS1983

Determination of aerodynamic parameters of a fighter airplane from flight data at high angles of attack

A procedure for the estimation of airplane model structure and parameters is applied to data from a modern fighter airplane operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, and the estimation method. The results presented contain basic longitudinal characteristics of the airplane and the estimates of aerodynamic parameters in the yawing-moment equations. These estimates are obtained from small and large amplitude maneuvers. Because the latter set of data was not suitable for airplane identification, some of the large amplitude maneuvers were joined together and then partitioned into subsets according to the values of angle of attack. Each subset was then analyzed as a separate data set. Most of the estimated parameters and functions are in good agreement with the wind tunnel measurements. The estimated lateral parameters in the model equations also demonstrate good prediction capabilities.

Klein, V.↗
NASA NTRS1983

An application of parameter identification to the oscillatory motion of an airplane at high C(L)

This paper presents an application of a stepwise regression incorporating polynomial splines to oscillatory flight data from a light research airplane operating at near stall angles of attack. It is shown that data from several experiments can be combined into a large data set for analysis and that hysteresis phenomena can be observed in this large data set. Finally, it is postulated from the analysis of the flight data and theoretical calculations that the observed oscillatory motion is the result of a combination of wing stall and wing wake position at the tail.

Batterson, J. G.↗
NASA NTRS1983

Determination of airplane model structure from flight data using splines and stepwise regression

A procedure for the determination of airplane model structure from flight data is presented. The model is based on a polynomial spline representation of the aerodynamic coefficients, and the procedure is implemented by use of a stepwise regression. First, a form of the aerodynamic force and moment coefficients amenable to the utilization of splines is developed. Next, expressions for the splines in one and two variables are introduced. Then the steps in the determination of an aerodynamic model structure and the estimation of parameters are discussed briefly. The focus is on the application to flight data of the techniques developed.

Klein, V.↗
NASA NTRS1983

Analysis of oscillatory motion of a light airplane at high values of lift coefficient

A modified stepwise regression is applied to flight data from a light research air-plane operating at high angles at attack. The well-known phenomenon referred to as buckling or porpoising is analyzed and modeled using both power series and spline expansions of the aerodynamic force and moment coefficients associated with the longitudinal equations of motion.

Batterson, J. G.↗
NASA NTRS1983

On the determination of airplane model structure form flight data

A procedure based on a modified stepwise regression and several selection criteria is presented for the determination of airplane model structure from flight data. The aerodynamic force and moment coefficients in an airplane model are expresed either as polynomials in output and input variables or as a combination of splines. The procedure is demonstrated in three examples by attempting to determine a local, extended and global model. Some of the resulting models are verified by using the maximum likelihood estimation or by examining model prediction capabilities.

Klein, V.↗