Engineering topics

Barbieri, Enrique

Publications and source records attributed to Barbieri, Enrique.

14 records

NASA NTRS2005

GUI for Computational Simulation of a Propellant Mixer

Control Panel is a computer program that generates a graphical user interface (GUI) for computational simulation of a rocket-test-stand propellant mixer in which gaseous hydrogen (GH2) is injected into flowing liquid hydrogen (LH2) to obtain a combined flow having desired thermodynamic properties. The GUI is used in conjunction with software that models the mixer as a system having three inputs (the positions of the GH2 and LH2 inlet valves and an outlet valve) and three outputs (the pressure inside the mixer and the outlet flow temperature and flow rate). The user can specify valve characteristics and thermodynamic properties of the input fluids via userfriendly dialog boxes. The user can enter temporally varying input values or temporally varying desired output values. The GUI provides (1) a set-point calculator function for determining fixed valve positions that yield desired output values and (2) simulation functions that predict the response of the mixer to variations in the properties of the LH2 and GH2 and manual- or feedback-control variations in valve positions. The GUI enables scheduling of a sequence of operations that includes switching from manual to feedback control when a certain event occurs.

Figueroa, Fernando↗

NASA NTRS2005

Matlab GUI for a Fluid Mixer

The Test and Engineering Directorate at NASA John C. Stennis Space Center developed an interest to study the modeling, evaluation, and control of a liquid hydrogen (LH2) and gas hydrogen (GH2) mixer subsystem of a ground test facility. This facility carries out comprehensive ground-based testing and certification of liquid rocket engines including the Space Shuttle Main engine. A software simulation environment developed in MATLAB/SIMULINK (M/S) will allow NASA engineers to test rocket engine systems at relatively no cost. In the progress report submitted in February 2004, we described the development of two foundation programs, a reverse look-up application using various interpolation algorithms, a variety of search and return methods, and self-checking methods to reduce the error in returned search results to increase the functionality of the program. The results showed that these efforts were successful. To transfer this technology to engineers who are not familiar with the M/S environment, a four-module GUI was implemented allowing the user to evaluate the mixer model under open-loop and closed-loop conditions. The progress report was based on an udergraduate Honors Thesis by Ms. Jamie Granger Austin in the Department of Electrical Engineering and Computer Science at Tulane University, during January-May 2003, and her continued efforts during August-December 2003. In collaboration with Dr. Hanz Richter and Dr. Fernando Figueroa we published these results in a NASA Tech Brief due to appear this year. Although the original proposal in 2003 did not address other components of the test facility, we decided in the last few months to extend our research and consider a related pressurization tank component as well. This report summarizes the results obtained towards a Graphical User Interface (GUI) for the evaluation and control of the hydrogen mixer subsystem model and for the pressurization tank each taken individually. Further research would combine the two components - mixer and tank, for a more realistic simulation tool.

Barbieri, Enrique↗

NASA NTRS2003

Small Signal Modelling and Control of the Hydrogen Mixer for Facility E1

We have undertaken the theoretical modelling of an existing liquid hydrogen (LH2) and gas hydrogen (GH2) mixer subsystem of the E1 Ground Test Facility at NASA John C. Stennis Space Center. The E1 test facility carries out comprehensive ground-based testing and certification of various liquid rocket engines and their components. The mixer described in this work is responsible for combining high pressure LH2 and GH2 to produce a hydrogen flow that meets certain thermodynamic properties before it is fed into a test article. The desired properties are maintained by precise control of the mixture of LH2 and GH2 flows. The mixer is modelled as a general multi-flow lumped volume for single constituent fluids using density and internal energy as states. The set of nonlinear differential equations is linearized about an equilibrium point and the resulting two-state, 3-input linear model is analyzed as a possible candidate for control design.

Barbieri, Enrique↗

NASA NTRS2003

Modeling, Simulation and Control of a Propellant Mixer

This paper addresses some modeling and control issues for a mixing chamber used in rocket engine testing at NASA Stennis Space Center. The mixer must combine high pressure liquid hydrogen (LH2) and gaseous hydrogen (GH2) to produce and output flow that meets certain thermodynamic properties before it is fed into a test article. More precisely, this paper considers that the quantities to be tracked and/or regulated are mixer internal pressure, exit mass flow, and exit temperature. The available control inputs are given by three value positions, namely those of the GH2, LH2 and exit valves. The mixer is modelled by a system of two nonlinear ordinary differential equations having density and internal energy as states. The model must be simple enough to lend itself to subsequent feedback controller design, yet its accuracy must be tested against real data. For this reason, the model includes function calls to thermodynamic property data. Some structural properties of the resulting model that pertain to controller design, such as controllability and uniqueness of the equilibrium point are shown to hold. Validation of the model against real data is also provided. As a first control approach, a small-signal (linear) model is developed based on the nonlinear model and simulated as well. Pulse disturbances are introduced to the valve positions and the quality of the linear model is ascertained by comparing its behavior against the nonlinear model simulations. Valve control strategies that simulate an operator-in-the-loop scenario are then explored demonstrating the need for automatic feedback control. Classical optimal single-output and multi-output Proportional/Integral controllers are designed based on the linear model and applied to the nonlinear model with excellent results to track simultaneous, constant setpoint changes in desired exit flow, exit temperature, and mixer pressure, as well as to reject unmeasurable but bounded additive step perturbations in the valve positions. A feedback linearization controller is designed and used to achieve tracking and regulation of the outputs over an extended range of the variables of interest.

Richter, Hanz↗

NASA NTRS2003

Point to Point Control of the Hydrogen Mixer

We continue to build on the theoretical modelling of a liquid hydrogen (LH2) and gas hydrogen (GH2) mixer subsystem. The mixer described in this work is responsible for combining high pressure LH2 and GH2 to produce a hydrogen flow that meets certain thermodynamic properties. The desired properties are maintained by precise control of the LH2 and GH2 flows. The mixer is modelled as a general multi-flow lumped volume for single constituent fluids using density and internal energy as states. The set of nonlinear differential equations is modelled in the SIMULINK environment including a table look-up feature of the fluid thermodynamic properties. A small signal (linear) model is developed based on the nonlinear model and simulated as well. Pulse disturbances are introduced to the valve positions and the quality of the linear model is ascertained by comparing its behavior against the nonlinear model simulations. Valve control strategies that simulate an operator-in-the-loop scenario are then explored demonstrating the need for automatic feedback control. Finally, optimal single-output and multi-output Proportional/Integral controllers are designed based on the linear model and applied to the nonlinear model with excellent results to track simultaneous, constant setpoint changes in desired exit flow, exit temperature, and mixer pressure, as well as to reject unmeasureable but bounded additive step perturbations in the valve positions.

Barbieri, Enrique↗

NASA NTRS2003

Nonlinear Modeling and Control of a Propellant Mixer

A mixing chamber used in rocket engine combustion testing at NASA Stennis Space Center is modeled by a second order nonlinear MIMO system. The mixer is used to condition the thermodynamic properties of cryogenic liquid propellant by controlled injection of the same substance in the gaseous phase. The three inputs of the mixer are the positions of the valves regulating the liquid and gas flows at the inlets, and the position of the exit valve regulating the flow of conditioned propellant. The outputs to be tracked and/or regulated are mixer internal pressure, exit mass flow, and exit temperature. The outputs must conform to test specifications dictated by the type of rocket engine or component being tested downstream of the mixer. Feedback linearization is used to achieve tracking and regulation of the outputs. It is shown that the system is minimum-phase provided certain conditions on the parameters are satisfied. The conditions are shown to have physical interpretation.

Barbieri, Enrique↗

NASA NTRS2003

Small Signal Point-to-Point Tracking of a Propellant Mixer

This paper addresses some theoretical modelling and control issues for a mixing chamber used in rocket engine testing at NASA Stennis Space Center. The mixer is responsible for combining high pressure LH2 and GH2 to produce a hydrogen flow that meets certain thermodynamic properties before it is fed into a test article. The desired properties are maintained by precise control of the LH2 and GH2 flows. The mixer is modelled as a general multi-flow lumped volume for single constituent fluids using density and internal energy as states. The set of nonlinear differential equations is modelled in the SIMULINK environment including a table look-up feature of the fluid thermodynamic properties. a small-signal (linear) model is developed based on the nonlinear model and simulated as well. Pulse disturbances are introduced to the valve positions and the quality of the linear model is ascertained by comparing its behavior against the nonlinear model simulations. Valve control strategies that simulate an operator-in-the-loop scenario are then explored demonstrating the need for automatic feedback control. Finally, classical optimal single-output and multi-output Proportional/Integral controllers are designed based on the linear model and applied to the nonlinear model with excellent results to track simultaneous, constant setpoint changes in desired exit flow, exit temperature, and mixer pressure, as well as to reject unmeasurable but bounded additive step perturbations in the valve positions.

Barbieri, Enrique↗

NASA NTRS2003

Modeling and Validation of a Propellant Mixer for Controller Design

A mixing chamber used in rocket engine testing at the NASA Stennis Space Center is modelled by a system of two nonlinear ordinary differential equations. The mixer is used to condition the thermodynamic properties of cryogenic liquid propellant by controlled injection of the same substance in the gaseous phase. The three inputs of the mixer are the positions of the valves regulating the liquid and gas flows at the inlets, and the position of the exit valve regulating the flow of conditioned propellant. Mixer operation during a test requires the regulation of its internal pressure, exit mass flow, and exit temperature. A mathematical model is developed to facilitate subsequent controller designs. The model must be simple enough to lend itself to subsequent feedback controller design, yet its accuracy must be tested against real data. For this reason, the model includes function calls to thermodynamic property data. Some structural properties of the resulting model that pertain to controller design, such as uniqueness of the equilibrium point, feedback linearizability and local stability are shown to hold under conditions having direct physical interpretation. The existence of fixed valve positions that attain a desired operating condition is also shown. Validation of the model against real data is likewise provided.

Richter, Hanz↗

NASA NTRS2001

Small Signal Modeling and Control of the Hydrogen Mixer for Facility E1

We have undertaken the theoretical modelling of an existing liquid hydrogen (LH2) and gas hydrogen (GH2) mixer subsystem of the E1 Ground Test Facility at NASA John C. Stennis Space Center. The E1 test facility carries out comprehensive ground-based testing and certification of various liquid rocket engines and their components. The mixer described in this work is responsible for combining high pressure before it is fed into a test article. The desired properties are maintained by precise control of the mixture of LH2 and GH2 flows. The mixer is modelled as a general multi-flow lumped volume for single constituent fluids using density and internal energy as states. The set of nonlinear differential equations is linearized about an equilibrium point and the resulting two-state, 3-input linear model is analyzed as a possible candidate for control design.

Barbieri, Enrique↗

NASA NTRS1993

Single-input/single-output transfer functions for a flexible slewing link

Truncated linear models based on constrained and unconstrained mode expansions for a flexible link with torque actuation at its hub led us to examine the behavior of the open-loop-zeros of five commonly used SISO transfer functions. We arrive at new conclusions with regard to minimum- and non-minimum-phase zeros, and passivity of the transfer functions. The flexible-to-rigid inertia (FRI) ratio plays an important role in the determination of these characteristics. This paper illustrates how the zero locations of some of the transfer functions are dramatically affected by the FRI ratio. We also investigate the performance of a hub angle, hub rate, and relative tip position static feedback controller based on a reduced-order constrained mode model when applied to both unconstrained and constrained mode models of the same dimension. Simulations indicate that the constrained model can be stable while the unconstrained model is not for high FRI ratios. Our findings can provide useful information to designers in cases where the controller is sensitive to the 1ocation of the plant's zeros.

Barbieri, Enrique↗

NASA NTRS1993

Momentum management in redundant manipulators for vibration suppression

This research project dealt with the development of control methodologies which would effectively use existing inertial devices as control actuators in the manipulation of Remote Manipulator System (RMS)-type robotic arms. The existing devices proposed to be investigated are the Torque-Wheel (TW) and the Proof-Mass actuator (PM). This report presents a succinct summary of our results.

Barbieri, Enrique↗

NASA NTRS1993

A new minimum-time control law for a one-mode model of a flexible slewing structure

We describe the construction of a new minimum-time control law for a single-axis, undamped, one-mode model of a flexible slewing structure. The set of necessary and sufficient conditions for optimality are developed using phase-plane techniques, and are given in terms of the vibration frequencies and the rigid-body states. This effectively provides the switching hypersurface in four-dimensional space. The resulting control strategy has the advantage that can be implemented on-line since no a priori computation of switching times is required.

Barbieri, Enrique↗

NASA NTRS1992

Nonlinear modeling of a long flexible manipulator and control by inertial devices

The authors consider the modeling and control of a planar, long flexible manipulator that is representative of current space-based robotic arms. The arm is equipped with three actuators: 1) a shoulder motor; 2) a torque wheel at the tip; and 3) a proof-mass actuator at the tip. The goal is to investigate the potential use of inertial devices as control inputs for maneuvering tasks and vibration suppression. The parameters used for the inertial devices at the tip are comparable to those specified for the Mini-Mast facility at the Langley Research Center. A nonlinear distributed parameter model is obtained by the extended Hamilton principle. The associated eigenvalue/eigenfunction problem is solved and a finite-dimensional state space model is assembled. A preliminary design of a linear quadratic regulator is used, and computer simulation results illustrate the benefits of using the proposed actuators.

Barbieri, Enrique↗

NASA NTRS1989

A control approach for robots with flexible links and rigid end-effectors

Multiarm flexible robots with dexterous end effectors are currently being considered in such tasks as satellite retrieval, servicing and repair where a two phase problem can be identified: Phase 1, robot positioning in space; Phase 2, object retrieval. Some issues in Phase 1 regarding modelling and control strategies for a robotic system comprised of along flexible arm and a rigid three-link end effector are presented. The control objective is to maintain the last (rigid) link stationary in space in the presence of an additive disturbance caused by the flexible energy in the first link after a positioning maneuver has been accomplished. Several configuration strategies can be considered, and optimal decentralized servocompensators can be designed. Preliminary computer simulations are included for a simple proportional controller to illustrate the approach.

Barbieri, Enrique↗