Engineering topics

Banks, Bruce A.

Publications and source records attributed to Banks, Bruce A..

At least 163 records · Page 9

NASA NTRS1992

Atomic oxygen undercutting of LDEF aluminized-Kapton multilayer insulation

Atomic oxygen undercutting is a potential threat to vulnerable spacecraft materials which have atomic oxygen protective coatings. Such undercutting is due to atomic oxygen attack of oxidizable materials at microscopic defects in the protective coatings. These defects occur during fabrication and handling, or from micrometeoroid and debris bombardment in space. An aluminized-polyimide Kapton multilayer insulation sample that was located on the leading edge of the Long Duration Exposure Facility (LDEF) was used to study low Earth orbit directed ram atomic oxygen undercutting. Cracks in the aluminized coatings located around vent holes provided excellent defect sites for evaluation of atomic oxygen undercutting. The experimentally observed undercutting profiles were compared to predictions from Monte Carlo models for normal incident ram atomic oxygen attack. The shape of the undercut profile was found to vary with crack width, which is proportional to the number of oxygen atoms entering the crack. The resulting profiles of atomic oxygen which occurred on LDEF indicated wide undercut cavities in spite of the fixed ram orientation. Potential causes of the observed undercutting are presented. Implications of the undercutting profiles relevant to the Space Station Freedom are also discussed.

Degroh, Kim K.↗

NASA NTRS1992

SiO(X) coatings for atomic oxygen protection of polyimide Kapton in low earth orbit

Sputter-deposited SiO(X) (where X between 1.9 and 2.0) thin film coatings have been found to be durable to atomic oxygen. Such coatings will be used to protect polyimide Kapton photovoltaic array blankets from atomic oxygen attack in low earth orbit (LEO) on the Space Station Freedom (SSF). Monte Carlo modeling of atomic oxygen attack at defect sites in protected Kapton exposed in laboratory RF plasma ashers and on solar tracking photovoltaic arrays in space has been conducted to enable understanding of degradation processes relevant to the durability of the SSF solar array blanket. SiO(X) protective coating performance data from RF plasma asher tests will be presented, along with Monte Carlo modeling considerations, to enable the projection of in-space durability of the SSF solar array blankets based on ground laboratory test results.

Banks, Bruce A.↗

NASA NTRS1992

Issues/considerations and performance prediction of LEO protective coatings

Organic materials can be used in low earth orbit for long periods only if they are made to be durable to atomic oxygen in addition to the threats of ultraviolet radiation, micrometeoroid and debris impact, thermal cycling, and charged particle radiation. In many materials applications, it is more cost-effective to utilize atomic oxygen protective coatings over materials which are vulnerable to attack by atomic oxygen rather than developing alternative materials which are inherently durable. Many metal and metal oxide coatings have been shown to be potentially suitable for long term protection of organic polymers in low earth orbit. The protection afforded by thin film coatings on polymeric substrates is highly dependent on the completeness of coverage of the coating. Thus, the prime indicator of durability is the size and abundance of pin windows and scratches in the protective coating. Such defects depend on the deposition technique, smoothness of the surface to be protected, and presence of particulate contaminants. Issues and considerations relevant to substrate preparation, deposition of protective coatings, ground laboratory simulation and evaluation of threats in low earth orbit to protective materials, results of in-space tests, and the use of Monte Carlo modeling techniques to predict in-space durability are presented in graphic form.

Banks, Bruce A.↗

NASA NTRS1992

Performance and properties of atomic oxygen protective coatings for polymeric materials

Such large LEO spacecraft as the Space Station Freedom will encounter high atomic oxygen fluences which entail the use of protective coatings for their polymeric structural materials. Such coatings have demonstrated polymer mass losses due to oxidation that are much smaller than those of unprotected materials. Attention is here given to protective and/or electrically conductive coatings of SiO(x), Ge, and indium-tin oxide which have been exposed to atomic oxygen in order to ascertain mass loss, electrical conductivity, and optical property dependence on atomic oxygen exposure.

Banks, Bruce A.↗

NASA NTRS1991

Low Earth orbital atomic oxygen micrometeoroid, and debris interactions with photovoltaic arrays

Polyimide Kapton solar array blankets can be protected from atomic oxygen in low earth orbit if SiO sub x thin film coatings are applied to their surfaces. The useful lifetime of a blanket protected in this manner strongly depends on the number and size of defects in the protective coatings. Atomic oxygen degradation is dominated by undercutting at defects in protective coatings caused by substrate roughness and processing rather than micrometeoroid or debris impacts. Recent findings from the Long Duration Exposure Facility (LDEF) and ground based studies show that interactions between atomic oxygen and silicones may cause grazing and contamination problems which may lead to solar array degradation.

Banks, Bruce A.↗

NASA NTRS1991

Atomic oxygen interactions with FEP Teflon and silicones on LDEF

The Long Duration Exposure Facility (LDEF) spacecraft represents the first controlled unidirectional exposure of high-fluence atomic oxygen on fluorinated ethylene propylene (FEP Teflon) and silicones. The atomic oxygen erosion yield for FEP Teflon was found to be significantly in excess of previous low fluence orbital data and is an order of magnitude below that of polyimide Kapton. LDEF FEP Teflon erosion yield data as a function of angle of attack is presented. Atomic oxygen interaction with silicon polymers results in crazing of the silicones as well as deposition of dark contaminant oxidation products on adjoining surfaces. Documentation of results and possible mechanistic explanations are presented.

Banks, Bruce A.↗

NASA NTRS1991

Arc-textured high emittance radiator surfaces

High emittance radiator surfaces are produced by arc-texturing. This process produces such a surface on a metal by scanning it with a low voltage electric arc from a carbon electrode in an inert environment.

Banks, Bruce A.↗

NASA NTRS1991

Atomic oxygen interaction with solar array blankets at protective coating defect sites

Atomic oxygen in the low-Earth-orbital environment oxidizes SiOx protected polyimide Kapton solar array blankets at sites which are not protected such as pin windows or scratches in the protective coatings. The magnitude and shape of the atomic oxygen undercutting which occurs at these sites is dependent upon the exposure environment details such as arrival direction and reaction probability. The geometry of atomic oxygen undercutting at defect sites exposed to atomic oxygen in plasma asher was used to develop a Monte Carlo model to simulate atomic oxygen erosion processes at defect sites in protected Kapton. Comparisons of Monte Carlo predictions and experimental results are presented for plasma asher atomic oxygen exposures for large and small defects as well as for protective coatings on one or both sides of Kapton. The model is used to predict in-space exposure results at defect sites for both directed and sweeping atomic oxygen exposure. A comparison of surface textures predicted by the Monte Carlo model and those experimentally observed from both directed space ram and laboratory plasma asher atomic oxygen exposure indicate substantial agreement.

Banks, Bruce A.↗

NASA NTRS1991

Flexible fluoropolymer filled protective coatings

Metal oxide films such as SiO2 are known to provide an effective barrier to the transport of moisture as well as gaseous species through polymeric films. Such thin film coatings have a tendency to crack upon flexure of the polymeric substrate. Sputter co-deposition of SiO2 with 4 to 15 percent fluoropolymers was demonstrated to produce thin films with glass-like barrier properties that have significant increases in strain to failure over pure glass films which improves their tolerance to flexure on polymeric substrates. Deposition techniques capable of producing these films on polymeric substrates are suitable for durable food packaging and oxidation/corrosion protection applications.

Banks, Bruce A.↗

NASA NTRS1991

LDEF spacecraft, ground laboratory, and computational modeling implications on Space Station Freedom's solar array materials and surfaces durability

The low earth orbital (LEO) durability of Space Station Freedom (SSF) solar array materials and surfaces is evaluated using results from the Long Duration Exposure Facility (LDEF), ground laboratory simulation tests, and Monte Carlo modeling. These results indicate that thin-film SiOx protective coatings are adequately durable to atomic oxygen, ultraviolet (UV) radiation, thermal cycling, and micrometeroid or debris impact.

Banks, Bruce A.↗

NASA NTRS1990

Heat transfer device and method of making the same

Gas derived graphite fibers are generated by the decomposition of an organic gas. These fibers when joined with a suitable binder are used to make a high thermal conductivity composite material. The fibers may be intercalated. The intercalate can be halogen or halide salt, alkaline metal, or any other species which contributes to the electrical conductivity improvement of the graphite fiber. The heat transfer device may also be made of intercalated highly oriented pyrolytic graphite and machined, rather than made of fibers.

Banks, Bruce A.↗

NASA NTRS1990

Materials degradation in low earth orbit (LEO); Proceedings of the Symposium, 119th Annual Meeting of the Minerals, Metals, and Materials Society, Anaheim, CA, Feb. 17-22, 1990

The current understanding of the effect of space environment on materials and the development of protective coatings is examined in reviews and reports. Consideration is given to hyperthermal atomic oxygen reactions, the effect of atomic oxygen on altered and coated Kapton surfaces for spacecraft applications in LEO, silicon dioxide space coatings studied ellipsometrically, atomic oxygen effects on spacecraft materials, atomic oxygen beam source for erosion simulation, and atomic oxygen effects on refractory materials. Particular attention is given to ellipsometric analysis of materials degradation in space, studies of the interaction of 8 km/s oxygen atoms with selected materials, characterization and calibration of the EOIM-III flight mass spectrometer in a high velocity oxygen atom beam, the reaction efficiency of thermal energy oxygen atoms with polymeric materials, and effects of simulated space environments on the properties of selected materials.

Srinivasan, V.↗

NASA NTRS1990

Atomic oxygen undercutting of defects on SiO2 protected polyimide solar array blankets

Low Earth Orbital (LEO) atomic oxygen can oxidize SiO2-protected polyimide kapton solar array blanket material which is not totally protected as a result of pinholes or scratches in the SiO2 coatings. The probability of atomic oxygen reaction upon initial impact is low, thus inviting oxidation by secondary impacts. The secondary impacts can produce atomic oxygen undercutting which may lead to coating mechanical failure and ever increasing mass loss rates of kapton. Comparison of undercutting effects in isotropic plasma asher and directed beam tests are reported. These experimental results are compared with computational undercutting profiles based on Monte Carlo methods and their implication on LEO performance of protected polymers.

Banks, Bruce A.↗

NASA NTRS1990

High emittance surfaces for high temperature space radiator applications

Surface modification techniques are evaluated for emittance enhancement of radiator surfaces. These techniques include acid etching, heat treating, abrasion, sputter texturing, electrochemical texturing, arc texturing, and atomic oxygen beam texturing. Candidate radiator surface materials under consideration include Nb-1 pct Zr, Cu, Ti, Ti-6 pct Al-4 pct V, 304 stainless steel, Al6061-T6, Mo, W, and Ta.

Banks, Bruce A.↗

NASA NTRS1989

Atomic oxygen effects on materials

Understanding of the basic processes of atomic oxygen interaction is currently at a very elementary level. However, measurement of erosion yields, surface morphology, and optical properties for low fluences have brought about much progress in the past decade. Understanding the mechanisms and those factors that are important for proper simulation of low Earth orbit is at a much lower level of understanding. The ability to use laboratory simulations with confidence to quantifiably address the functional performance and durability of materials in low Earth orbit will be necessary to assure long-term survivability to the natural space environment.

Banks, Bruce A.↗

NASA NTRS1989

Flexible, Polymer-Filled Metallic Conductors

Procedure developed to make materials both flexible and reasonably good electrical conductors. Metal or polymer sheet substrate cleaned with beam of energetic inert-gas ions to remove adsorbed gases and contaminants from surface. After cleaning, substrate coated by cosputter deposition of both conductive metal and flexible polymer. Removed by either mechanical or chemical-dissolution technique, and resulting flexible metal/polymer conductor bonded at low temperature to conductor-surface contacts.

Banks, Bruce A.↗

NASA NTRS1989

Simulation of the low earth orbital atomic oxygen interaction with materials by means of an oxygen ion beam

Atomic oxygen is the predominant species in low-Earth orbit between the altitudes of 180 and 650 km. These highly reactive atoms are a result of photodissociation of diatomic oxygen molecules from solar photons having a wavelength less than or equal to 2430A. Spacecraft in low-Earth orbit collide with atomic oxygen in the 3P ground state at impact energies of approximately 4.2 to 4.5 eV. As a consequence, organic materials previously used for high altitude geosynchronous spacecraft are severely oxidized in the low-Earth orbital environment. The evaluation of materials durability to atomic oxygen requires ground simulation of this environment to cost effectively screen materials for durability. Directed broad beam oxygen sources are necessary to evaluate potential spacecraft materials performance before and after exposure to the simulated low-Earth orbital environment. This paper presents a description of a low energy, broad oxygen ion beam source used to simulate the low-Earth orbital atomic oxygen environment. The results of materials interaction with this beam and comparison with actual in-space tests of the same meterials will be discussed. Resulting surface morphologies appear to closely replicate those observed in space tests.

Banks, Bruce A.↗

NASA NTRS1989

Low earth orbital atomic oxygen simulation for materials durability evaluation

The erosion yields of numerous materials have been evaluated in low earth orbital space tests. There appears to be three classes of materials: materials of high erosion yield which include most of the hydrocarbon organic materials; materials which either do not react with atomic oxygen or form self-protecting oxides which allow the underlying material to appear durable to atomic oxygen, and materials with low but nonnegligeable erosion yields, such as fluoropolymers. A NASA atomic oxygen effects test program has been established to utilize collective data from a multitude of simulation facilities to promote an understanding of mechanism and erosion yield dependencies. Atomic oxygen protective coatings for Kapton polymide solar array blankets, fiberglass-epoxy composite mast structures, and solar dynamic power system concentrator surfaces have been identified and evaluated under atomic oxygen exposure in RF plasma asher laboratory tests. The control of defect density in protective coatings appears to be the key to the assurance of long-term protection of oxidizable materials in low earth orbit.

Banks, Bruce A.↗