Engineering Papers⌕ Search

Engineering topics

Bajorek, Stephen

Publications and source records attributed to Bajorek, Stephen.

Tree-Based Ensemble Learning Models for Wall Temperature Predictions in Post-Critical Heat Flux Flow Regimes at Subcooled and Low-Quality Conditions

Accurately predicting post-critical heat flux (CHF) heat transfer is an important but challenging task in water-cooled reactor design and safety analysis. Although numerous heat transfer correlations have been developed to predict post-CHF heat transfer, these correlations are only applicable to relatively narrow ranges of flow conditions due to the complex physical nature of the post-CHF heat transfer regimes. In this paper, a large quantity of experimental data is collected and summarized from the literature for steady-state subcooled and low-quality film boiling regimes with water as the working fluid in vertical tubular test sections. In addition, a low-quality water film boiling (LWFB) database is consolidated with a total of 22,813 experimental data points, which cover a wide flow range of the system pressure from 0.1 to 9.0 MPa, mass flux from 25 to 2750 kg/m 2 s, and inlet subcooling from 1 to 70 °C. Two machine learning (ML) models, based on random forest (RF) and gradient boosted decision tree (GBDT), are trained and validated to predict wall temperatures in post-CHF flow regimes. The trained ML models demonstrate significantly improved accuracies compared to conventional empirical correlations. To further evaluate the performance of these two ML models from a statistical perspective, three criteria are investigated and three metrics are calculated to quantitatively assess the accuracy of these two ML models. For the full LWFB database, the root-mean-square errors between the measured and predicted wall temperatures by the GBDT and RF models are 5.7% and 6.2%, respectively, confirming the accuracy of the two ML models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Thermal-Hydraulic and Neutronic Phenomena Important in Modeling and Simulation of Liquid-Fuel Molten Salt Reactors

In this paper, we discuss liquid-fuel molten salt (cooled) reactors (MSRs); how they will operate under normal, transient, and accident conditions; and the results of an expert elicitation to determine the corresponding thermal-hydraulic and neutronic phenomena important to understanding their behavior. Identifying these phenomena will enable the U.S. Nuclear Regulatory Commission (NRC), U.S. Department of Energy, and industry to develop or identify modeling functionalities and tools required to carry out confirmatory and licensing analyses that examine the validity and accuracy of an applicant's calculations and help determine the margin of safety in plant design. The NRC frequently does an expert elicitation using a Phenomena Identification and Ranking Table (PIRT) to identify and evaluate the state of knowledge of important modeling phenomena. However, few details about the design of these reactors and the sequence of events during accidents are known, so the process used was considered a preliminary PIRT. A panel comprising a group of subject matter experts met to define phenomena that would need to be modeled and considered the impact/importance of each phenomenon with respect to specific figures of merit (FoMs) (e.g., salt temperature, velocity, and composition). Each FoM reflected a potential impact on radionuclide release or loss of a barrier to release. The panel considered what the path forward might be with respect to being able to model the phenomenon in a simulation code. Results are explained for both thermal and fast spectrum designs, with an emphasis on the thermal-hydraulic takeaways. It was concluded that compared to light water reactors, the lack of high-pressure operation, energetic break flow, depressurization, and quench front tracking may simplify some aspects of an MSR analysis. However, MSRs have new phenomena both for a license applicant and NRC confirmatory analysis. There is a need for enhanced understanding of physical properties for MSRs that encompass several individual thermophysical properties, including thermal conductivity, viscosity, specific heat, density, optical properties, thermodynamic properties, volatilities, solubilities, etc. Salt composition is closely linked to both these properties and the neutronics of the system. Additionally, the large number of MSR concepts and system designs means that there is wide variation in the potential modeling needs for these systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Thermal-Hydraulics Phenomena Important in Modeling and Simulation of Liquid-Fuel Molten Salt Reactors

This paper discusses liquid-fuel molten salt reactors, how they will operate under normal, transient, and accident conditions, and the results of an expert elicitation to determine the corresponding thermalhydraulic phenomena important to understanding their behavior. Identifying these phenomena will enable the U.S. Nuclear Regulatory Commission (NRC) to develop or identify modeling functionalities and tools required to carry out confirmatory analyses that examine the validity and accuracy of an applicant’s calculations and help determine the margin of safety in plant design. NRC frequently does an expert elicitation using a Phenomena Identification and Ranking Table (PIRT) to identify and evaluate the state of knowledge of important modeling phenomena. However, few details about the design of these reactors and the sequence of events during accidents are known, so the process used was considered a preliminary PIRT. A panel met to define phenomena that would need to be modeled and considered the impact/importance of each phenomenon with respect to specific figures-of-merit (FoMs) (e.g., salt temperature, velocity, and composition). Each FoM reflected a potential impact on radionuclide release or loss of a barrier to release. The panel considered what the path forward might be with respect to being able to model the phenomenon in a simulation code. Results are explained for both thermal and fast spectrum designs.

42 ENGINEERING↗

Phenomena identification and ranking table study for thermal hydraulics for Advanced High Temperature Reactor

The Advanced High-Temperature Reactor (AHTR) is a conceptual design of a Fluoride salt-cooled High-temperature Reactor (FHR) utilizing 7 LiF-BeF 2 (66-34 mol%) as its primary coolant. To identify key phenomena that impose potential challenges on thermal hydraulics modeling and simulation of such a reactor system, a thermal hydraulics phenomena identification and ranking table (TH-PIRT) study was performed for the AHTR in a Department of Energy Nuclear Energy University Program (NEUP) integrated research project led by Georgia Institute of Technology. A panel of experts from regulators, industries, national laboratories, and academia was assembled for the study. In this paper, the TH-PIRTs identified by the panel for two events, namely, station blackout and simultaneous withdrawal of all control rods, are summarized and discussed in detail. In addition, the key phenomena that warrant further study and research for AHTR analysis are identified to support the validation of thermal hydraulics system-level analysis codes and computational fluid dynamics simulation tools, as well as future FHR reactor licensing.

42 ENGINEERING↗

Phenomena identification and categorization by the required level of multiphysics coupling in FHR modeling and simulation

Here, this study identifies the phenomena that impact the accuracy of the multiphysics analysis of fluoride salt-cooled high temperature reactors (FHR) and categorizes the level of coupling needed to model these phenomena with sufficient accuracy in the context of three scenarios, namely, normal operation, station blackout, and simultaneous withdrawal of all control rods. Such a study is a necessary step prior to developing or extending existing multiphysics modeling and simulation tools. The identified multiphysics phenomena are categorized into the groups requiring ‘‘tight” and ‘‘loose” coupling. ‘‘Tight” coupling refers to phenomena that require iterative feedback between multiple physics modules/methods whereas ‘‘loose” coupling refers to phenomena that require only data from other physics that can be pre-calculated and shared in tabular or functional form. For the station blackout scenario, it was determined that no identified phenomena required tight coupling. For the rod withdrawal and normal operation scenarios, it is found that there is a large number of phenomena that require tight coupling between neutronics and thermal hydraulics.

42 ENGINEERING↗

Phenomena Important in Molten Salt Reactor Simulations

The U.S. Nuclear Regulatory Commission (NRC) is preparing for the future licensing of advanced reactors that will be very different from current light water reactors. Part of the NRC preparation strategy is to identify the simulation tools that will be used for confirmatory safety analysis of normal operation and abnormal situations in those reactors. This report advances that strategy for reactors that will use molten salts (MSRs). This includes reactors with the fuel within the salt as well as reactors using solid fuel. Although both types are discussed in this report, the emphasis is on those reactors with liquid fuel because of the perception that solid-fuel MSRs will be significantly easier to simulate. These liquid-fuel reactors include thermal and fast neutron spectrum alternatives. The specific designs discussed in the report are a subset of many designs being considered in the U.S. and elsewhere but they are considered the most likely to submit information to the NRC in the near future. The objective herein, is to understand the design of proposed molten salt reactors, how they will operate under normal or transient/accident conditions, and what will be the corresponding modeling needs of simulation tools that consider neutronics, heat transfer, fluid dynamics, and material composition changes in the molten salt. These tools will enable the NRC to eventually carry out confirmatory analyses that examine the validity and accuracy of applicant’s calculations and help determine the margin of safety in plant design.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluation of interfacial area transport models for horizontal bubbly flow

This paper presents evaluation results of interfacial area transport equation (IATE) for horizontal air-water bubbly flow. The steady-state one-dimensional, one-group IATE for adiabatic air-water bubbly flow developed by Talley [1] is employed in the current evaluation study. The models evaluated include: (a) drift-flux-based closure relations for void-weighted bubble velocity and void fraction; (b) frictional pressure drop model based on the Lockhart-Martinelli approach; (c) bubble interaction mechanisms; and (d) covariance associated with asymmetric bubble distribution in horizontal two-phase flow. In order to evaluate the models, a local two-phase flow database obtained by the four-sensor conductivity probe in fourteen different test conditions is employed, which covers a wide range of flow conditions in horizontal bubbly flow regime, with superficial liquid and gas velocities ranging from 3.50-6.00 m/s and 0.09- 1.00 m/s, respectively. It is demonstrated that both the void weighted bubble velocity and void fraction are predicted well with an average percent difference of ±2.7%. The fictional pressure loss can be predicted with an average percent difference of ±1.12%. The covariance parameters calculated from the modeling approach generally compare well with those calculated from experimental data within ±20% difference. It is found that the IATE generally predicts the measured interfacial area concentration with an average percent difference of ±5.7%. Furthermore, the effect of liquid velocity on individual bubble interaction mechanisms is investigated. It is found that both the contributions of random collision and turbulent impact decrease as liquid velocity decreases. (authors)

42 ENGINEERING↗

Image Analysis for Plug Bubbles in Horizontal Flow

Horizontal plug flow is different from horizontal slug flow in that relatively few small bubbles exist in plug flow, whereas slug flow is characterized by highly aerated liquid slugs and liquid films. While the nose position and nose propagation velocity of plug bubbles may provide physical insights in understanding the flow regime transition mechanism between the plug and slug flows, few systematic investigations on these parameters have been performed in previous research. In view of this, this paper presents the development of an image processing method for the purpose of (a) obtaining data for nose position and nose propagation velocity of plug bubbles and (b) benchmarking local four-sensor conductivity probe measurements of time-averaged bubble velocity and void fraction. (authors)

42 ENGINEERING↗

Drift-flux Analysis in Horizontal Two-phase Flow

While the most detailed approach to model two-phase flows is the two-fluid model, the drift-flux model may also provide effective methods for estimating one-dimensional two-phase flow parameters. For example, in the current nuclear system analysis codes, the interfacial drag force is a function of the void fraction, drift velocity, and area-averaged relative velocity, which are estimated based on drift-flux approach. While correlations for these parameters exist for vertical two-phase flows, correlations for horizontal two-phase flows have not been developed. (authors)

42 ENGINEERING↗