Engineering topics

Bainum, Peter M.

Publications and source records attributed to Bainum, Peter M..

29 records · Page 2

NASA NTRS1988

The dynamics and control of large flexible space structures, part 11

A mathematical model is developed to predict the dynamics of the proposed Spacecraft Control Laboratory Experiment during the stationkeeping phase. The Shuttle and reflector are assumed to be rigid, while the mass connecting the Shuttle to the reflector is assumed to be flexible with elastic deformations small as compared with its length. It is seen that in the presence of gravity-gradient torques, the system assumes a new equilibrium position primarily due to the offset in the mass attachment point to the reflector from the reflector's mass center. Control is assumed to be provided through the Shuttle's three torquers and throught six actuators located by painrs at two points on the mass and at the reflector mass center. Numerical results confirm the robustness of an LQR derived control strategy during stationkeeping with maximum control efforts significantly below saturation levels. The linear regulator theory is also used to derive control laws for the linearized model of the rigidized SCOLE configuration where the mast flexibility is not included. It is seen that this same type of control strategy can be applied for the rapid single axis slewing of the SCOLE through amplitudes as large as 20 degrees. These results provide a definite trade-off between the slightly larger slewing times with the considerable reduction in over-all control effort as compared with the results of the two point boundary value problem application of Pontryagin's Maximum Principle.

Bainum, Peter M.↗

NASA NTRS1988

The dynamics and control of large-flexible space structures, part 10

A mathematical model is developed to predict the dynamics of the proposed orbiting Spacecraft Control Laboratory Experiment (SCOLE) during the station keeping phase. The equations of motion are derived using a Newton-Euler formulation. The model includes the effects of gravity, flexibility, and orbital dynamics. The control is assumed to be provided to the system through the Shuttle's three torquers, and through six actuators located by pairs at two points on the mast and at the mass center of the reflector. The modal shape functions are derived using the fourth order beam equation. The generic mode equations are derived to account for the effects of the control forces on the modal shape and frequencies. The equations are linearized about a nominal equilibrium position. The linear regulator theory is used to derive control laws for both the linear model of the rigidized SCOLE as well as that of the actual SCOLE including the first four flexible modes. The control strategy previously derived for the linear model of the rigidized SCOLE is applied to the nonlinear model of the same configuration of the system and preliminary single axis slewing maneuvers conducted. The results obtained confirm the applicability of the intuitive and appealing two-stage control strategy which would slew the SCOLE system, as if rigid to its desired position and then concentrate on damping out the residual flexible motions.

Bainum, Peter M.↗

NASA NTRS1988

Minimum time attitude slewing maneuvers of a rigid spacecraft

The minimum time attitude slewing motion of a rigid spacecraft with its controls provided by torques and forces, which have their upper and lower limits prescribed, is considered. The two-point boundary-value problem is derived by applying the Pontriagin's Maximum Principle to the system and solved by using a quasi-linearization algorithm. The nominal solutions to the problem as well as the starting values of the total slewing time and the unknown initial costates for this algorithm are generated by using Euler's eigenaxis rotation theorem. It is pointed out that one of the four initial costates associated with the quaternions can be arbitrarily selected without affecting the optimal controls and, thus, simplifying the computation. The minimum slewing time is determined by shortening the total slewing time until at least one of the controls becomes a bang-bang type. Several numerical tests for the rigidized SCOLE model are presented to show the applications of the methods.

Li, Feiyue↗

NASA NTRS1988

The dynamics and control of the orbiting spacecraft control laboratory experiment (SCOLE) during station keeping

A mathematical model is developed to predict the dynamics of the proposed orbiting Spacecraft Control Laboratory Experiment during the station keeping phase. The Shuttle as well as the reflector are assumed to be rigid, the mast is flexible and is assumed to undergo elastic displacements very small as compared with its length. The equations of motion are derived using a Newton-Euler formulation. The model includes the effects of gravity, flexibility, and orbital dynamics. The control is assumed to be provided to the system through the Shuttle's three torquers, and through six actuators located by pairs at two points on the mast and at the mass center of the reflector. At each of the locations, an actuator acts parallel to the roll axis while the other one acts parallel to the pitch axis. It is seen that, in the presence of gravity-gradient torques in the system dynamics, the system assumes a new equilibrium position about which the equations must be linearized, primarily due to the offset in the mast attachment point to the reflector. The linear regulator theory is used to derive control laws for the linear model of the SCOLE including the first four flexible modes. Numerical results confirm the robustness of this control strategy for station keeping with maximum control efforts significantly below saturation levels.

Bainum, Peter M.↗

NASA NTRS1988

The equations of motion for a general orbiting large space flexible system

General motion equations in compact form using dyadic notation are developed for an orbiting flexible body of arbitrary shape. The equations are applied to three typical flexible space systems: a flexible beam, a flexible plate, and a flexible shallow spherical shell in orbit. The inertia dyadic of these flexible bodies may be calculated using the equations which have been obtained.

Xing, Guangqian↗

NASA NTRS1987

The dynamics and control of large flexible space structures X, part 1

The effect of delay in the control system input on the stability of a continuously acting controller which is designed without considering the delay is studied. The stability analysis of a second order plant is studied analytically and verified numerically. For this example it is found that the system becomes unstable for a delay which is equivalent to only 16 percent of its natural period of motion. It is also observed that even a small amount of natural damping in the system can increase the amount of delay that can be tolerated before the onset of instability. The delay problem is formulated in the discrete time domain and an analysis procedure suggested. The maximum principle from optimal control theory is applied to minimize the time required for the slewing of a general rigid spacecraft. The slewing motion need not be restricted to a single axis maneuver. The minimum slewing time is calculated based on a quasi-linearization algorithm for the resulting two point boundary value problem. Numerical examples based on the rigidized in-orbit model of the SCOLE also include the more general reflector line-of-sight slewing maneuvers.

Bainum, Peter M.↗

NASA NTRS1987

Issues in modeling and controlling the SCOLE configuration

The parametric study of the in-plane Spacecraft Control Laboratory Experiment (SCOLE) system, the Floquet Stability Analysis, and three dimensional formulations of the SCOLE system dynamics are examined. Control issues are discussed, such as: control of large structures with delayed input in continuous time; control with delayed input in discrete time; control law design for SCOLE using Linear Quadratic Gaussian (LQC)/TRR technique; and optimal torque control for SCOLE slewing maneuvers.

Bainum, Peter M.↗

NASA NTRS1987

Minimum time attitude slewing maneuvers of a rigid spacecraft

The problems of large-angle attitude maneuvers of a spacecraft have gained much consideration in recent years. The configurations of the spacecraft considered are: completely rigid, a combination of rigid and flexible parts, or gyrostat-type systems. The performance indices usually include minimum torque integration, power criterion, and frequency-shaped cost functionals. The minimum time slewing problem of a rigid spacecraft was examined. Optimal control theory (Maximum Principal) was applied to the slewing motion of a general rigid spacecraft. Control torque about all three axes was computed. The equations for the system are composed of the Euler dynamical equations in the spacecraft body axes and the quaternion kinematical equation. By introducing the costates for the quaternion and the angular velocity, the Hamiltonian of the system can be formed and the optimal control obtained. Finally the methods are applied to the SCOLE slewing motion. The control variables include three control moments on the Shuttle and two control forces on the reflector. Numerical results are discussed.

Li, Feiyue↗

NASA NTRS1987

Tethers in space; Proceedings of the International Conference, Arlington, VA, Sept. 17-19, 1986

A collection of papers on the applications of tethers in space is presented. Tether flight experiments of the past, in planning stages, and in the future are examined. Tether dynamics and the applications and technical aspects of electrodynamic tethers are addressed. The use of tethers on the Space Station and applications in the Space Station era are considered. Individual tether technology issues, including tether materials and instrumentation for atmospheric measurements are discussed.

Bainum, Peter M.↗

NASA NTRS1986

A review of modelling techniques for the open and closed-loop dynamics of large space systems

This paper reviews the steps in the development of mathematical models that can be used to simulate the in-orbit dynamic behavior of large flexible systems. A general continuum formulation is compared with the hybrid coordinate formulation and also a finite element representation of the total system. A review of structural analysis routines emphasizes the use of computer generated graphics to help understand the different modal elastic shape functions of complex systems. Numerical techniques employed to synthesize shape and attitude control laws are summarized. Finally, the modeling of environmental disturbance torques due to the interaction of solar radiation pressure on vibrating and thermally deflected systems is discussed.

Bainum, Peter M.↗

NASA NTRS1984

Preliminary results of the dynamics and control of the SCOLE system

The Spacecraft Control Laboratory Experiment (SCOLE) system is assumed to be comprised of three main parts: the Space Shuttle Orbiter with its center of mass located at 0(sub 1); the mast, treated as a 130 ft long beam, connected to the Shuttle at 0(sub 2) and to the reflector at 0(sub 3); and the reflector, considered to be a flat plate with its center of mass at 0(sub 4). In the analysis given here, the angular momentum of the entire system is evaluated at point 0(sub 1) and the dynamics include the lateral displacements of the beam.

Bainum, Peter M.↗