Engineering Papers⌕ Search

Engineering topics

Baca, Albert G.

Publications and source records attributed to Baca, Albert G..

At least 19 records

AlGaN High Electron Mobility Transistor for High-Temperature Logic

Here we report on AlGaN high electron mobility transistor (HEMT)-based logic development, using combined enhancement- and depletion-mode transistors to fabricate inverters with operation from room temperature up to 500°C. Our development approach included: (a) characterizing temperature-dependent carrier transport for different AlGaN HEMT heterostructures, (b) developing a suitable gate metal scheme for use in high temperatures, and (c) over-temperature testing of discrete devices and inverters. Hall mobility data (from 30°C to 500°C) revealed the reference GaN-channel HEMT experienced a 6.9x reduction in mobility, whereas the AlGaN channel HEMTs experienced about a 3.1x reduction. Furthermore, a greater aluminum contrast between the barrier and channel enabled higher carrier densities in the two-dimensional electron gas for all temperatures. The combination of reduced variation in mobility with temperature and high sheet carrier concentration showed that an Al-rich AlGaN-channel HEMT with a high barrier-to-channel aluminum contrast is the best option for an extreme temperature HEMT design. Three gate metal stacks were selected for low resistivity, high melting point, low thermal expansion coefficient, and high expected barrier height. The impact of thermal cycling was examined through electrical characterization of samples measured before and after rapid thermal anneal. The 200-nm tungsten gate metallization was the top performer with minimal reduction in drain current, a slightly positive threshold voltage shift, and about an order of magnitude advantage over the other gates in on-to-off current ratio. After incorporating the tungsten gate metal stack in device fabrication, characterization of transistors and inverters from room temperature up to 500°C was performed. The enhancement-mode (e-mode) devices’ resistance started increasing at about 200°C, resulting in drain current degradation. This phenomenon was not observed in depletion-mode (d-mode) devices but highlights a challenge for inverters in an e-mode driver and d-mode load configuration.

42 ENGINEERING↗

Thermal Conductivity of β-Phase Ga 2 O 3 and (Al x Ga 1– x ) 2 O 3 Heteroepitaxial Thin Films

Heteroepitaxy of β-phase gallium oxide (β-Ga 2 O 3 ) thin films on foreign substrates shows promise for the development of next-generation deep ultraviolet solar blind photodetectors and power electronic devices. In this work, the influences of the film thickness and crystallinity on the thermal conductivity of ($\bar{2}01$)-oriented β-Ga 2 O 3 heteroepitaxial thin films were investigated. Unintentionally doped β-Ga 2 O 3 thin films were grown on c-plane sapphire substrates with off-axis angles of 0° and 6° toward $\langle$$11\bar{2}0$$\rangle$ via metal–organic vapor phase epitaxy (MOVPE) and low-pressure chemical vapor deposition. The surface morphology and crystal quality of the β-Ga 2 O 3 thin films were characterized using scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. The thermal conductivities of the β-Ga 2 O 3 films were measured via time-domain thermoreflectance. The interface quality was studied using scanning transmission electron microscopy. The measured thermal conductivities of the submicron-thick β-Ga 2 O 3 thin films were relatively low as compared to the intrinsic bulk value. The measured thin film thermal conductivities were compared with the Debye–Callaway model incorporating phononic parameters derived from first-principles calculations. The comparison suggests that the reduction in the thin film thermal conductivity can be partially attributed to the enhanced phonon-boundary scattering when the film thickness decreases. They were found to be a strong function of not only the layer thickness but also the film quality, resulting from growth on substrates with different offcut angles. Growth of β-Ga 2 O 3 films on 6° offcut sapphire substrates was found to result in higher crystallinity and thermal conductivity than films grown on on-axis c-plane sapphire. However, the β-Ga 2 O 3 films grown on 6° offcut sapphire exhibit a lower thermal boundary conductance at the β-Ga 2 O 3 /sapphire heterointerface. In addition, the thermal conductivity of MOVPE-grown ($\bar{2}01$)-oriented β-(Al x Ga 1–x ) 2 O 3 thin films with Al compositions ranging from 2% to 43% was characterized. Because of phonon-alloy disorder scattering, the β-(Al x Ga 1–x ) 2 O 3 films exhibit lower thermal conductivities (2.8–4.7 W/m∙K) than the β-Ga 2 O 3 thin films. The dominance of the alloy disorder scattering in β-(Al x Ga 1–x ) 2 O 3 is further evidenced by the weak temperature dependence of the thermal conductivity. This work provides fundamental insight into the physical interactions that govern phonon transport within heteroepitaxially grown β-phase Ga 2 O 3 and (Al x Ga 1–x ) 2 O 3 thin films and lays the groundwork for the thermal modeling and design of β-Ga 2 O 3 electronic and optoelectronic devices.

36 MATERIALS SCIENCE↗

Device-Level Multidimensional Thermal Dynamics With Implications for Current and Future Wide Bandgap Electronics

Researchers have been extensively studying wide-bandgap (WBG) semiconductor materials such as gallium nitride (GaN) with an aim to accomplish an improvement in size, weight, and power of power electronics beyond current devices based on silicon (Si). However, the increased operating power densities and reduced areal footprints of WBG device technologies result in significant levels of self-heating that can ultimately restrict device operation through performance degradation, reliability issues, and failure. Typically, self-heating in WBG devices is studied using a single measurement technique while operating the device under steady-state direct current measurement conditions. However, for switching applications, this steady-state thermal characterization may lose significance since the high power dissipation occurs during fast transient switching events. Therefore, it can be useful to probe the WBG devices under transient measurement conditions in order to better understand the thermal dynamics of these systems in practical applications. In this work, the transient thermal dynamics of an AlGaN/GaN high electron mobility transistor (HEMT) were studied using thermoreflectance thermal imaging and Raman thermometry. Also, the proper use of iterative pulsed measurement schemes such as thermoreflectance thermal imaging to determine the steady-state operating temperature of devices is discussed. These studies are followed with subsequent transient thermal characterization to accurately probe the self-heating from steady-state down to submicrosecond pulse conditions using both thermoreflectance thermal imaging and Raman thermometry with temporal resolutions down to 15 ns.

42 ENGINEERING↗

High temperature operation to 500 °C of AlGaN graded polarization-doped field-effect transistors

AlGaN polarization-doped field-effect transistors were characterized by DC and pulsed measurements from room temperature to 500 °C in ambient. DC current-voltage characteristics demonstrated only a 70% reduction in on-state current from 25 to 500 °C and full gate modulation, regardless of the operating temperature. Near ideal gate lag measurement was realized across the temperature range that is indicative of a high-quality substrate and sufficient surface passivation. The ability for operation at high temperature is enabled by the high Schottky barrier height from the Ni/Au gate contact, with values of 2.05 and 2.76 eV at 25 and 500 °C, respectively. The high barrier height due to the insulatorlike aluminum nitride layer leads to an ION/IOFF ratio of 1.5 × 10 9 and 6 × 10 3 at room temperature and 500 °C, respectively. Transmission electron microscopy was used to confirm the stability of the heterostructure even after an extended high-temperature operation with only minor interdiffusion of the Ni/Au Schottky contact. The use of refractory metals in all contacts will be key to ensure a stable extended high-temperature operation.

36 MATERIALS SCIENCE↗

Regrowth method for fabricating wide-bandgap transistors, and devices made thereby

Methods are provided for fabricating a HEMT (high-electron-mobility transistor) that involve sequential epitaxial growth of III-nitride channel and barrier layers, followed by epitaxial regrowth of further III-nitride material through a window in a mask layer. The regrowth takes place on the barrier layer, only in the access region or regions. Devices made according to the disclosed methods are also provided.

36 MATERIALS SCIENCE↗

High current density, low contact resistance wide bandgap contacts

A high current density, low contact resistance contact for wide bandgap (WBG) or ultra-wide bandgap materials (UWBG) is disclosed. The contact is lithographically formed so that a total perimeter length of the contact structure is at least twice the length of the side of a contact pad closest to the gate in a high electron mobility transistor (HEMT). The contact structure may take the form of a plurality of columns having various cross-sectional shapes, or may take the form of a convoluted geometrical shape, such as a comb-like, serpentine, or spiral shape. The depth of the contact structure permits direct contact with the two-dimensional electron gas (2DEG) in the HEMT by the perimeter of the contact structure. The contact structure is formed of at least one metal layer, at least one doped material regrown layer, or at least one implanted region. The contact structure may be applied to other WBG and UWBG devices.

36 MATERIALS SCIENCE↗

Multidimensional thermal analysis of an ultrawide bandgap AlGaN channel high electron mobility transistor

Improvements in radio frequency and power electronics can potentially be realized with ultrawide bandgap materials such as aluminum gallium nitride (AlxGa 1-x N). Multidimensional thermal characterization of an Al 0.30 Ga 0.70 N channel high electron mobility transistor (HEMT) was done using Raman spectroscopy and thermoreflectance thermal imaging to experimentally determine the lateral and vertical steady-state operating temperature profiles. An electrothermal model of the Al 0.30 Ga 0.70 N channel HEMT was developed to validate the experimental results and investigate potential device-level thermal management. While the low thermal conductivity of this III-N ternary alloy system results in more device self-heating at room temperature, the temperature insensitive thermal and electrical output characteristics of Al x Ga 1-x N may open the door for extreme temperature applications.

36 MATERIALS SCIENCE↗