Engineering topics

Babel, Henry W.

Publications and source records attributed to Babel, Henry W..

9 records

NASA NTRS2006

Method to increase the toughness of aluminum-lithium alloys at cryogenic temperatures

A method to increase the toughness of the aluminum-lithium alloy C458 and similar alloys at cryogenic temperatures above their room temperature toughness is provided. Increasing the cryogenic toughness of the aluminum-lithium alloy C458 allows the use of alloy C458 for cryogenic tanks, for example for launch vehicles in the aerospace industry. A two-step aging treatment for alloy C458 is provided. A specific set of times and temperatures to age the aluminum-lithium alloy C458 to T8 temper is disclosed that results in a higher toughness at cryogenic temperatures compared to room temperature. The disclosed two-step aging treatment for alloy 458 can be easily practiced in the manufacturing process, does not involve impractical heating rates or durations, and does not degrade other material properties.

Sankaran, Krishnan K.↗

NASA NTRS2003

Stable, Thermally Conductive Fillers for Bolted Joints

A commercial structural epoxy [Super Koropon (or equivalent)] has been found to be a suitable filler material for bolted joints that are required to have large thermal conductances. The contact area of such a joint can be less than 1 percent of the apparent joint area, the exact value depending on the roughnesses of the mating surfaces. By occupying the valleys between contact peaks, the filler widens the effective cross section for thermal conduction. In comparison with prior thermal joint-filler materials, the present epoxy offers advantages of stability, ease of application, and -- as a byproduct of its stability -- lasting protection against corrosion. Moreover, unlike silicone greases that have been used previously, this epoxy does not migrate to contaminate adjacent surfaces. Because this epoxy in its uncured state wets metal joint surfaces and has low viscosity, it readily flows to fill the gaps between the mating surfaces: these characteristics affect the overall thermal conductance of the joint more than does the bulk thermal conductivity of the epoxy, which is not exceptional. The thermal conductances of metal-to-metal joints containing this epoxy were found to range between 5 and 8 times those of unfilled joints.

LeVesque, Raymond J., II↗

NASA NTRS2003

An Update on C458 AI-Li for Cryotanks

This viewgraph representation provides an overview of ongoing research being conducted on C458 Al-Li composite cryotanks. Topics covered include: structural design of C458 Al-Li cryotanks, C458 ingot casting capability, C458 plate properties, summary of attained properties, design database capabilities, fatigue tests and testing, and ongoing research projects.

Babel, Henry W.↗

NASA NTRS2002

Assessment of Al-Li Alloys for Cryotanks

This viewgraph presentation provides information on steps undertaken to determine the suitability of Aluminum and Lithium alloys in cryogenic tank construction. Major characteristics are offered for several different candidate alloys including reliability, weldability, flammability, and required thicknesses.

Babel, Henry W.↗

NASA NTRS1996

High pressure mechanical seal

A relatively impervious mechanical seal is formed between the outer surface of a tube and the inside surface of a mechanical fitting of a high pressure fluid or hydraulic system by applying a very thin soft metal layer onto the outer surface of the hard metal tube and/or inner surface of the hard metal fitting. The thickness of such thin metal layer is independent of the size of the tube and/or fittings. Many metals and alloys of those metals exhibit the requisite softness, including silver, gold, tin, platinum, indium, rhodium and cadmium. Suitably, the coating is about 0.0025 millimeters (0.10 mils) in thickness. After compression, the tube and fitting combination exhibits very low leak rates on the order or 10.sup.-8 cubic centimeters per second or less as measured using the Helium leak test.

Babel, Henry W.↗

NASA NTRS1996

Improved Mechanical Seals For Tubes

Improved tube-to-fitting seals made by application of soft metal pieces to either ends of tubes or to interior of fittings. Metal silver, gold, platinum, tin, or other easily malleable metal selected to be inert with fluid of use. Metal plated, evaporated, or sputter-deposited. Coat of soft metal thin, so no changes required in design or tolerances of standard fittings. Technique suitable for hydraulic or other fluid systems in which leakage from mechanically joined sections of tubes occur.

Babel, Henry W.↗

NASA NTRS1995

High pressure mechanical seal

A relatively impervious mechanical seal is formed between the outer surface of a tube and the inside surface of a mechanical fitting of a high pressure fluid or hydraulic system by applying a very thin soft metal layer onto the outer surface of the hard metal tube and/or inner surface of the hard metal fitting, prior to swaging the fitting onto the tube. The thickness of such thin metal layer is independent of the size of the tube and/or fittings. Many metals and alloys of those metals exhibit the requisite softness, including silver, gold, nickel, tin, platinum, indium, rhodium and cadmium. Suitably, the coating is about 0.0025 millimeters (0.10 mils) in thickness. After swaging, the tube and fitting combination exhibits very low leak rates on the order or 10.sup.-8 cubic centimeters per second or less as meaured using the Helium leak test.

Babel, Henry W.↗

NASA NTRS1995

LDEF's contribution to the selection of thermal control coatings for the Space Station

The design of the Space Station presented new challenges in the selection and qualification of thermal control materials that would survive in low Earth orbit for a duration of up to 30 years. Prior to LDEF, flight data were obtained from Orbiting Solar Observatory (OSO) satellites, a number of Orbiter flights, and limited ground tests. The excellent data obtained from the OSO satellites were based on calorimetry and temperature measurements which were transmitted to Earth; these satellites were not recovered. For some of these flight experiments it was difficult to distinguish between changes due to contamination, atomic oxygen (AO), ultraviolet radiation (UV), particle radiation and the synergistic effects between them. The data from Shuttle flights were primarily focused on developing a better understanding of atomic oxygen (AO) effects. Although UV and AO were present, the relatively short duration of the Orbiter flights, about one week, was viewed as too short to show the effects from UV or possible synergistic interactions with AO and contamination. At the beginning of the program in 1989 there was no established design data base for AO resistant thermal control coatings for the Space Station. Then came the Long Duration Exposure Facility (LDEF). It provided the first long life data for materials exposed and recovered from space with a characterized environment. Post flight analysis proved data on the effects of contamination on optical properties in the ram (velocity) and wake directions and the erosion of Teflon and multilayer insulation (MLI) covers. The results from LDEF confirmed and, in some cases, modified the approach used for the Space Station, as well as helped to focus our development activities. These development activities resulted in a number of new technical solutions which are applicable to many spacecraft surfaces and missions. LDEF also showed the detrimental effects that could occur from silicone contamination, an issue that has not been completely resolved. An investigation was initiated in 1993 on the effects of silicone contamination and was continuing at the time this paper was prepared.

Babel, Henry W.↗

NASA NTRS1994

Protective, Sacrificial Coats On Optical Surfaces

Clear, easily cleaned sacrificial coats of polytetrafluoroethylene, polyurethane, silicone, or other low-outgassing organic films help maintain optical properties of surfaces of radiators, solar panels, and other components. Contamination removed by erosion of coats. Applied by conventional spraying or other techniques. Originally coats intended to protect surfaces of radiators on spacecraft in low orbit around the Earth. On Earth, used to protect optical surfaces against damage during manufacture or protect and facilitate cleaning of optical surfaces particularly delicate or otherwise not cleaned easily.

Babel, Henry W.↗