Engineering Papers⌕ Search

Engineering topics

Asle Zaeem, Mohsen

Publications and source records attributed to Asle Zaeem, Mohsen.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A molecular dynamics study of domain switching in BiFeO 3 nanofilm under DC electric field

The performance of ferroelectric materials is deeply rooted in the domain switching process triggered by an applied electric field. To understand the effect of controlling factors on the domain switching characteristics, nanoscale studies are essential. In this work, an atomistic-scale computational framework is developed to study the domain switching process of bismuth ferrite (BiFeO 3 ) nanofilms. Through a series of molecular dynamics simulations, the effects of duration and magnitude of an electric field, domain size and nanofilm thickness on the domain switching behavior are investigated. The evolution of domains under different magnitudes and durations of the applied electric field is studied, and the results of unswitched and switched cases are summarized in a switching map. Analysis of various nanofilms reveals that by increasing the film thickness, the switching time is increased. Additionally, the nanofilms with different domain sizes and configurations are examined, and the minimum domain size for complete reversal switching is obtained. Our results are helpful to predict and tune the switching process in ferroelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Transformation-induced fracture toughening in CuAlBe shape memory alloys: A phase-field study

Stress-induced transformation ahead of a crack tip can relax the stress concentration and produce fracture toughness in shape memory alloys (SMAs). In this manuscript, we utilize a nonisothermal phase-field model (PFM) to study the martensitic transformation induced crack tip toughening in CuAlBe SMA. The force-displacement curve, transformation zone and high stress zone in single crystalline samples show high dependency on the grain orientation with respect to the crack alignment. Comparison between isothermal and non-isothermal simulations reveals that the transformation-induced self-heating decreases the toughening capability by increasing the critical transformation stress. Investigating the high stress zones in CuAlBe and the nontransforming CuAl alloy shows that the toughening is obtained by redistributing the stress concentration far from the crack tip, as the high stress zone follows the tip of the transformation zone. Increasing the acuity of the crack tip is found to generate more symmetric martensite wings on both side of the crack axis and a more localized high stress zone. The polycrystal specimen displays higher toughening due to the internal constraints related to the presence of various grains with difference orientations. Depending on the orientation of the grain inclosing the crack tip, the toughening can be lower or higher. Finally, coincidence of the crack tip with a triple junction is found to improve the toughening behavior.

42 ENGINEERING↗
DOE OSTI2020

On the elastocaloric effect in CuAlBe shape memory alloys: A quantitative phase-field modeling approach

We report the reversible stress-induced phase transformation in shape memory alloys (SMAs) is a dissipative process during which heat is absorbed or released. The inherent temperature variations inside the material has an elastocaloric effect (eCE) with appealing applications in solid-state cooling technology such as compact and efficient on-board refrigeration system for eletronic devices. In this manuscript, we conduct the first study of eCE of CuAlBe SMAs utilizing phase-field modeling. For an applied stress of 500 MPa, the results for polycrystalline Cu-Al11-2Be (at. %) show a minimum adiabatic unloading temperature change of -10 K over a pseudoelastic window of 40 K. In the absence of plastic deformation, the material demonstrates good reproducibility of the eCE over a few loading–unloading cycles. The presence of plastic deformation is found to cause functional fatigue that deteriorates the cooling capacity; however, the coefficient of performance only decreases from 9.04 to 8.03, which is still a very good value. These results place CuAlBe as a frontrunner SMA for solid-state cooling compared to the expensive NiTi.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A phase-field model for non-isothermal phase transformation and plasticity in polycrystalline yttria-stabilized tetragonal zirconia

Here we propose an elastoplastic phase-field (PF) model to investigate the mechanics of tetragonal-to-monoclinic phase transformation (TMPT) and elastoplastic deformation of polycrystalline yttria-stabilized tetragonal zirconia (YSTZ). A Landau polynomial with non-vanishing chemical energy at the equilibrium temperature is introduced to account for the actual formation energies of the phases. The effects of different grain orientations, latent heat, and temperature on TMPT and deformation mechanisms are considered. The suppressive transformation effects of the grain boundaries (GBs) is modeled using an inhomogeneous kinetic coefficient in the bulk and GBs. The simulation results for single crystals demonstrate the capability of the model to reproduce the orientation-dependent compressive deformation of YSTZ similar to atomistic simulations and micropillar experiments. The single crystal with [100] crystallographic orientation along the loading direction (SC[100]) displays both TMPT and plasticity, SC[101] experiences only phase transformation, while SC[001] undergoes only plastic yielding. The TMPT induced by compressive loading exhibits shape memory effect (SME) below the equilibrium transformation temperature and pseudoelasticity above it, while the critical transformation stress increases with increasing loading temperature. The irrecoverable plastic strain is found to trap a part of the monoclinic phase, which prevents a complete reverse transformation. The polycrystalline cases also display SME and PE at low and high temperatures, respectively. Due to the orientation differences between grains and the stress concentrations at geometric nonlinearities, plastic deformation occurs in polycrystalline YSTZ for an applied load less than the yield stress. The results suggest a possible limitation of plasticity and an improvement of the shape recovery of YSTZ if one can control the orientation of the grains and/or increase the density of stacking faults at the GBs during material processing.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of twin boundaries and pre-existing defects on mechanical properties and deformation mechanisms of yttria-stabilized tetragonal zirconia

In annealing of yttria-stabilized tetragonal zirconia (YSTZ), {011}-specific twins and sub-surface defects are often observed, however their effects on the martensitic phase transformation and deformation behavior of YSTZ have never been investigated. In this work, the roles of twin boundaries (TBs) and pre-existing defects in determining the mechanical properties and subsequent deformation mechanisms of YSTZ nanopillars are studied. Using large-scale molecular dynamics simulations, we show that Young’s modulus and strength of YSTZ decrease with the increase of TB density, but the ductility of YSTZ pillars increases. Phase transformation behavior is found to be correlated to TB density. The sensitivity of mechanical responses of twinned structures to pre-existing defects is also studied. A competitive mechanism between TB-induced phase transformation and void-induced phase transformation is observed. When the diameter of a pre-existing void is smaller than a critical value, only TB-induced phase transformation occurs, which leads to void-insensitive mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A review of computational modeling techniques in study and design of shape memory ceramics

Shape memory ceramics are a unique family of shape memory materials with a wide variety of applications, such as ultra-high energy dissipation and high-temperature actuation. Along with significant progress in the experimental study of zirconia-based shape memory ceramics in recent years, computational simulations have exhibited powerful capabilities in revealing nano/microstructure-dependent deformation and failure mechanisms in these materials. In this work, we review the recent progress in understanding the phase transformation behavior in shape memory ceramics, focusing on computational modeling of zirconia-based ceramics. Electronic structure calculations have provided new data on the phase stability and surface properties of shape memory ceramics. At the nanometer length scale, molecular dynamics simulations have captured fundamental information about martensitic phase transformation and the effects of grain boundaries and defects on mechanical response of bi- and polycrystalline zirconia-based ceramics. At the micrometer length scale, advanced phase-field models have shown the ability to predict morphological evolution of microstructures and the corresponding mechanical responses in good agreement with experimental observations. Despite the recent multiscale computational advancements, further developments are required to establish processing-structure-property-performance relations that will lead to reliable and practical strategies for designing zirconia-based (or other) ceramics with improved and sustained shape memory responses. This article critically reviews current computational modeling techniques and provides an outlook for the study and design of the next generation of shape memory ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Rapid Solidification and Phase Transformations in Additive Manufactured Materials

Within the past few years, additive manufacturing (AM) has emerged as a promising manufacturing technique to enable the production of complex engineering structures with high efficiency and accuracy. Among the important factors establishing AM as a sustainable manufacturing process is the ability to control the microstructures and properties of AM products. In most AM processes, such as laser sintering (LS), laser melting (LM), and laser metal deposition (LMD), rapid solidification and high-temperature phase transformations play primary roles in determining nano- and microstructures, and consequently the mechanical and other properties of AM products. This topic of JOM is dedicated to summarizing the current research efforts in the area of rapid solidification and phase transformations in additively manufactured materials. Finally, a brief summary follows below of 10 journal articles in this topic.

36 MATERIALS SCIENCE↗