Engineering Papers⌕ Search

Engineering topics

Ash, R. L.

Publications and source records attributed to Ash, R. L..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Measurement of convective heat transfer to solid cylinders inside ventilated shrouds

The influence of ventilated cylindrical shrouds on the convective heat transfer to circular cylinders has been studied experimentally. Geometries studied were similar to those used in commercially available platinum resistance thermometers. Experiments showed that thermal response (convection) was enhanced when the shroud ventilation factor was approximately 20 percent (80 percent solid), and that maximum enhancement occurred when the ventilation holes were located symmetrically on either side of the stagnation lines.

Daryabeigi, K.↗
NASA NTRS1982

Autonomous oxygen production for a Mars return vehicle

The way in which a chemical processor that uses the Martian atmosphere as its only feedstock, thereby reducing the mass that must be launched from earth, can help to return a surface sample from Mars from a single Space Shuttle launch is described. Richter's (1981) study on both the theoretical and experimental aspects of oxygen separation using yttria-stabilized zirconia membranes is cited. Here, separation is accomplished by applying a voltage across the membrane which results in the selective conduction of oxygen ions from one side to the other. It is noted that by using thermal dissociation of the carbon dioxide in the Martian atmosphere to produce oxygen (and carbon monoxide), these zirconia electrolytic cells can be employed to separate oxygen from the atmospheric stream. Descriptions are also given of atmospheric filtration, atmospheric compression, and waste heat recovery, and of the oxygen precooler and oxygen compressor.

Ash, R. L.↗
NASA NTRS1981

A class of unsteady, three-dimensional flow structures in turbulent boundary layers

A restricted class of mathematically admissible, unsteady, three dimensional flows was identified which may constitute part of the structure observed in turbulent boundary layers. The development of the model and some general results are discussed. The resulting solution has characteristics which suggest how upwelling low speed flow can trigger a downward jetting of irrotational high speed fluid into the boundary layer.

Ash, R. L.↗
NASA NTRS1980

Outer planet satellite return missions using in situ propellant production

In situ production of oxygen and oxygen with hydrogen for utilization as return propellant from the Galilean satellites has been investigated. Europa has emerged as the preferred landing sight because of the availability of water ice and its surface temperature. When oxygen is used with methane transported from earth, a Europa sample return mission requires 4000 kg less estimated earth launch mass than a vehicle using space storable propellant. Neither methane nor oxygen require active refrigeration at Europa. When oxygen and hydrogen are both utilized to form the primary sample return propellant, the required processor mass increases, but the estimated earth launch mass requirement is reduced by an additional 550 kg.

Ash, R. L.↗
NASA NTRS1980

In Situ Propellant Production for improved sample return mission performance

In Situ Propellant Production (ISPP) on the surface of a target body is evaluated as a potential way to relax sample return mass constraints and to improve mission performance. Utilization of an oxygen/methane bipropellant combination for primary outbound and return propulsion has a significant favorable impact upon Earth escape requirements. A small sample can be returned from Mars using a single Shuttle/IUS(Twin) launch. Performance and design data are presented for the Mars mission. For sample returns from selected Galilean satellites, launch requirements are reduced by fifteen to forty percent. An assessment is made of overall utility of ISPP to planetary missions.

Stancati, M. L.↗
NASA NTRS1980

Hybrid suction surface for turbulent boundary layer flow

A hybrid suction surface which combines favorable aspects of both uniformly porous and discrete opening suction surfaces has been evaluated experimentally for use with incompressible turbulent boundary layers. The surface consisted of an array of closely spaced slots aligned in the direction of the freestream flow. Direct drag and mean boundary layer velocity profile measurements showed that the slotted surface had nominally the same suction characteristics as a uniformly porous surface.

Wilkinson, S. P.↗
NASA NTRS1979

Balloon concepts for scientific investigation of Mars and Jupiter

Opportunities for scientific investigation of the atmospheric planets using buoyant balloons have been explored. Mars and Jupiter were considered in this study because design requirements at those planets bracket nominally the requirements at Venus, and plans are already underway for a joint Russian-French balloon system at Venus. Viking data has provided quantitative information for definition of specific balloon systems at Mars. Free flying balloons appear capable of providing valuable scientific support for more sophisticated Martian surface probes, but tethered and powered aerostats are not attractive. The Jovian environment is so extreme, hot atmosphere balloons may be the only scientific platforms capable of extended operations there. However, the estimated system mass and thermal energy required are very large.

Ash, R. L.↗
NASA NTRS1979

In situ propellant production - A new potential for round-trip spacecraft

In situ propellant production (ISPP) greatly reduces the Earth escape requirements for some roundtrip missions, particularly Mars Sample Return. ISPP systems are described which produce oxygen or oxygen and methane from available atmospheric and surface materials. With ISPP, a 1 kg sample can be returned direct from Mars using a single Shuttle launch. Mars entry can be either direct or from orbit. Comet and asteroid sample return is also accomplished within a single Shuttle launch. Launch requirements for round-trip missions to Ganymede and Callisto are reduced by 15 to 40%.

Stancati, M. L.↗
NASA NTRS1978

Feasibility of rocket propellant production on Mars

In situ production of rocket propellant to reduce landed mass requirements for Mars return missions has been investigated. The analysis has shown that a system which utilizes atmospheric carbon dioxide and soil moisture to produce liquid methane-oxygen propellant requires a landed mass which is less than half the mass of the ascent vehicle it produces.

Ash, R. L.↗
NASA NTRS1978

Simulation of turbulent wall pressure

A Monte Carlo procedure was developed to simulate turbulent boundary layer wall pressure fluctuations. The approach utilizes much of the newly available conditional sampling information to construct the required distribution functions. Various disturbance wave forms were examined, as well as the effect of frequency-dependent decay. Good agreement between the simulation and experimental data was achieved for root mean square pressure level, power spectrum, and space time correlation.

Ash, R. L.↗
NASA NTRS1977

Effect of compliant wall motion on turbulent boundary layers

A critical analysis of available compliant wall data which indicated drag reduction under turbulent boundary layers is presented. Detailed structural dynamic calculations suggest that the surfaces responded in a resonant, rather than a compliant, manner. Alternate explanations are given for drag reductions observed in two classes of experiments: (1) flexible pipe flows and (2) water-backed membranes in air. Analysis indicates that the wall motion for the remaining data is typified by short wavelengths in agreement with the requirements of a possible compliant wall drag reduction mechanism recently suggested by Langley.

Bushnell, D. M.↗
NASA NTRS1977

Influence of transverse surface waves on turbulent boundary layers

Wavy wall experiments using solid waves and progressive waves have been reported. For this paper, the major effects of waviness of the wall on the flow are identified as due to oscillatory curvature (convex-concavity) and oscillatory acceleration/deceleration of the flow, which imposes a highly nonequilibrium influence upon the turbulence structure. The theoretical analysis in this presentation takes into account proper turbulence modeling (including the nonequilibrium effects) for the wavy wall problem. The analysis proceeds in three stages: (1) inviscid solution for induced pressure due to the physical wall, (2) solution of a turbulent boundary layer with pressure gradients and curvature effects in the modeling from which the profile correction is computed, and (3) induced pressure computations for the corrected profile. The phase shift of pressure perturbations with respect to the physical wall can be predicted, and pressure drag and skin friction drag can be estimated, with nonlinear viscous effects included. Comparison of the theoretical estimates with experimental data are also presented.

Balasubramanian, R.↗
NASA NTRS1977

Compliant wall surface motion and its effect on the structure of a turbulent boundary layer

The status of the continuing compliant wall drag reduction research at NASA-Langley Research Center is discussed. Preliminary surface motion calculations are reported along with compliant surface design concepts and their numerical models. A compliant drag reduction theory based on stabilizing the turbulent substructure is proposed and previous experiments have been examined relative to that theory. Results of recent low speed compliant surface experiments have been reported which include initial attempts to measure local compliant surface motion.

Ash, R. L.↗
NASA NTRS1976

Effective thermal property improves phase change paint data

The phase-change coating technique presents itself as a valuable tool in determining the heat transfer rate over the surface of small complex wind tunnel models. A numerical technique is described which shows that an effective thermophysical property - the square root of the product of thermal conductivity, density, and specific heat - may significantly improve the accuracy of the phase-change coating technique with allowance for model inhomogeneity and temperature dependency in a transient environment. Results of the measured steady-state variation of the effective thermophysical property with temperature and the effect of surface heating rate on the effective thermophysical property are plotted for a representative homogeneous model material and for an extreme nonhomogeneous model material. The use of an effective thermophysical property to reduce phase-change paint data is recommended. The analysis also confirms that the apparatus described by Corwin and Kramer (1975) can be used to measure directly this effective thermophysical property for use in wind tunnel model heat-transfer measurements.

Drummond, J. P.↗
NASA NTRS1976

Simulation of turbulent wall pressure

A computer program has been developed to simulate the transient wall pressure field produced by a low speed fully turbulent boundary layer. The theoretical basis for the simulation has been discussed and preliminary results from a pressure simulation are presented.

Ash, R. L.↗
NASA NTRS1975

Experimental verification of turbulent skin friction reduction with compliant walls

Preliminary compliant wall skin friction test results obtained in a low-turbulence pressure tunnel are reported. Compliant surface skins consisted of 0.0025 cm thick mylar, stretched under tension and area-bonded or longitudinally strip-bonded with silicone rubber adhesive to polyurethane foam. Mean velocity and fluctuating survey data were obtained with a single slanted hot wire. Mean velocity profiles for the area-bonded mylar surface skins indicated up to a 20% reduction in boundary-layer thickness (and lower momentum thickness) over rigid surfaces. This reduction in boundary-layer thickness indicates that a drag reduction occurred. In addition, a 16% reduction in wall shear was evident for the mylar/compressor foam compliant surface.

Weinstein, L. M.↗
NASA NTRS1975

Compliant wall-turbulent skin-friction reduction research

Previous compliant-wall experiments successful in reducing skin-friction drag probably have had a (unplanned) membrane resonance at a favorable frequency, amplitude, wave shape, length, and speed. The most probable drag reduction mechanism involves a direct coupling between the fluid and the moving wall when the wall natural resonance frequencies are near the fundamental turbulent burst frequency. Local skin-friction reductions of 61% were measured with mylar/PVC plastisol compliant surfaces. These reductions were observed only at certain flow conditions, indicating that changing tunnel total temperature may have altered the substrate dynamic modulus, damping, and coupled mylar tension. Apparently, the coupled membrane/substrate must be excited in compatible narrow-band natural frequency modes. An accelerated effort is required to develop practical durable compliant surfaces optimized for maximum drag reduction. Application of compliant walls to other transportation modes appears feasible with liquid flows offering the greatest skin-friction drag reduction potential.

Fischer, M. C.↗