Engineering Papers⌕ Search

Engineering topics

Argibay, Nicolas

Publications and source records attributed to Argibay, Nicolas.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Crack mitigation in additively manufactured AlCrFe 2 Ni 2 high-entropy alloys through engineering phase transformation pathway

The far-from-equilibrium solidification during additive manufacturing often creates large residual stresses that induce solid-state cracking. Here we present a strategy to suppress solid-state cracking in an additively manufactured AlCrFe 2 Ni 2 high-entropy alloy via engineering phase transformation pathway. We investigate the solidification microstructures formed during laser powder-bed fusion and directed energy deposition, encompassing a broad range of cooling rates. At high cooling rates (10 4 –10 6 K/s), we observe a single-phase BCC/B2 microstructure that is susceptible to solid-state cracking. At low cooling rates (10 2 –10 4 K/s), FCC phase precipitates out from the BCC/B2 matrix, resulting in enhanced ductility (~10 %) and resistance to solid-state cracking. Site-specific residual stress/strain analysis reveals that the ductile FCC phase can largely accommodate residual stresses, a feature which helps relieve residual strains within the BCC/B2 phase to prevent cracking. Our work underscores the value of exploiting the toolbox of phase transformation pathway engineering for material design during additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Theory-guided design of duplex-phase multi-principal-element alloys

Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure Alignment Effects from Engineered Cooling during Additive Manufacturing of Alnico Magnets from Prealloyed Powder

Alnico is a rare-earth free; permanent magnet (PM) which maintains its saturation magnetization while at temperatures up to 550°C but lacks the coercivity and energy product needed for a wide range of demanding applications. With an optimal set of processing and manufacturing techniques, Alnico could replace Dy-free Nd-Fe-B magnets in certain applications if the microstructure is textured in a $\langle$001$\rangle$ direction. Additive manufacturing (AM) of near-net-shape magnets may provide such texture. To investigate the possibility, directed-energy deposition (DED) in conjunction with an actively cooled substrate was used to build samples with a compositionally modified, gas-atomized, Alnico 8 alloy. The resulting samples were solutionized and quenched, followed by magnetic annealing and a heat treatment. Magnetic properties and microstructures are compared to previous work.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Refractory high entropy alloy compact heat exchanger

Several innovative technologies, including pressure-drop minimization, advanced refractory high entropy alloys, and advanced manufacturing can provide a compact heat exchanger that extends the state-of-the-art heat-exchanger operating range. The compact heat exchanger can reduce pressure drop losses by 100 to 500%, while retaining most of the heat transfer. The compact heat exchanger can be fabricated from refractory high entropy alloys that have favorable corrosion, thermal fatigue, and creep properties at high temperatures and pressures. Therefore, the compact heat exchanger using high entropy alloys can operate at >800° C. and 80 bars.

Kustas, Andrew↗
DOE OSTI2023

A ductility metric for refractory-based multi-principal-element alloys

We propose a quantum-mechanical dimensionless metric, the local-lattice distortion (LLD), as a reliable predictor of ductility in refractory multi-principal-element alloys (RMPEAs). The LLD metric is based on electronegativity differences in localized chemical environments and combines atomic-scale displacements due to local lattice distortions with a weighted average of valence-electron count. To evaluate the effectiveness of this metric, we examined body-centered cubic (bcc) refractory alloys that exhibit ductile-to-brittle behavior. Our findings demonstrate that local-charge behavior can be tuned via composition to enhance ductility in RMPEAs. With finite-sized cell effects eliminated, the LLD metric accurately predicted the ductility of arbitrary alloys, which compares well with existing tensile-elongation experiments. To validate further, we qualitatively evaluated the ductility of two refractory RMPEAs, i.e., NbTaMoW and Mo 72 W 13 Ta 10 Ti 2.5 Zr 2.5 , through the observation of crack formation under indentation, again showing excellent agreement with LLD predictions. Additionally, a comparative study of three refractory alloys provides further insights into the electronic-structure origin of ductility in refractory RMPEAs. This proposed metric enables rapid and accurate assessment of ductility behavior in the vast RMPEA composition space.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Universal Maximum Strength of Solid Metals and Alloys

As described here, interstitial electron density ρ o is offered as a direct metric for maximum strength in metals, arising from universal properties derived from an electron-gas – ρ o sets the exchange-correlation parameter r s in density-functional theory (DFT). It holds also for maximum shear strength τ max in polycrystals [Phys. Rev. Lett. 124, 125501]. Elastic moduli and τ max for polycrystalline (amorphous) metals are linear with ρ o and melting T m (glass-transition T g ) temperature. ρ o or r s , even with rule-of-mixture estimate, predicts relative strength for rapid, reliable selection of high-strength alloys with ductility, as confirmed for elements to steels to complex solid-solutions, and validated experimentally.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of Refractory Alloys Produced by Laser Additive Manufacturing

Refractory alloys often possess superior thermomechanical properties compared to conventional materials, such as steels, Ni-based superalloys, and Ti alloys, especially in high-temperature environments. While these materials promise to revolutionize numerous industries, significant hurdles remain for insertion into applications due to an incomplete understanding of structure-property relationships and conventional processing challenges. We explore laser-based additive manufacturing (AM) to construct refractory alloys consisting of combinations of Mo, Nb, Ta, and Ti with systematically increasing compositional complexity. Microstructure, composition, and hardness of the AM-processed alloys were characterized. Results are discussed in the context of pairing additive manufacturing with refractory metals to enable next-generation alloys.

Kustas, Andrew B.↗
DOE OSTI2022

Extreme hardness at high temperature with a lightweight additively manufactured multi-principal element superalloy

Materials are needed that can tolerate increasingly harsh environments, especially ones that retain high strength at extreme temperatures. Higher melting temperature alloys, like those consisting primarily of refractory elements, can greatly increase the efficiency of turbomachinery used in grid electricity production worldwide. Existing alloys, including Ni- and Co-based superalloys, used in components like turbine blades, bearings, and seals, remain a performance limiting factor due to their propensity, despite extensive optimization efforts, for softening and diffusion-driven elongation at temperatures often well above half their melting point. To address this critical materials challenge, we present results from integrating additive manufacturing and alloy design to guide significant improvements in performance via traditionally difficult-to-manufacture refractory alloys. We present an example of a multi-principal element alloy (MPEA), consisting of five refractory elements and aluminum, that exhibited high hardness and specific strength surpassing other known alloys, including superalloys. The alloy shows negligible softening up to 800°C and consists of four compositionally distinct phases, in distinction to previous work on MPEAs. Density functional theory calculations reveal a thermodynamic explanation for the observed temperature-independent hardness and favorability for the formation of this multiplicity of phases.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Science-Based Acceleration of the Full Value Stream for Metal Additive Manufacturing: Expedited Powder Development and Additive Manufacturing Deployment in the Areas of Ni-Base Superalloy and Custom Alloy Powders for AM

The overall Science-based Acceleration of the Full Value Stream for Metal Additive Manufacturing (AM): Expedited Powder Development and Additive Manufacturing Deployment (“X-P4AM”) project objective is to drastically reduce the time-to-market barriers for new additive alloys of interest in automotive and aerospace applications, through computational alloy design with rapid screening and down- selection via synthesis of candidate alloys with rapid solidification. The project will also refine the technology in high pressure gas atomization to improve the production of commercial quantities of selected powders with high powder yields and enhanced powder quality. Production of modified nickel-based superalloys and a Ni-containing alloy based on a high entropy composition, enhanced powder production methods, and optimized AM build parameterization provided critical steps in widespread adoption of AM technology for aerospace applications, in this case. The individual backgrounds and capabilities of the Parties are ideally suited to the successful execution of this work. The included work enhanced the Contractors’ AM capabilities, a core competency of the Contractors, and develop a close working relationship with the Participant in the areas of nickel-based powder superalloys and custom alloys and their end use.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Linking Friction Scales from Nano to Macro via Avalanches

Abstract Steady-state fluctuations in the friction force of molybdenum disulfide (MoS 2 ), a prototypical lamellar solid, were analyzed experimentally for newton-scale forces and computationally via molecular dynamics simulations for nanonewton-scale forces. A mean field model links the statics and the dynamics of the friction behavior across these eight orders of magnitude in friction force and six orders of magnitude in friction force fluctuations (i.e., avalanches). Both the statistics and dynamics of the avalanches match model predictions, indicating that friction can be characterized as a series of avalanches with properties that are predictable over a wide range of scales.

Salners, Tyler (ORCID:0000000332647944)↗