Anthony Colozza | Engineering Papers

NASA NTRS2026

Prototype Demonstration of an Integrated Solar Concentrator System and Carbothermal Reactor Using Solar Energy to Extract Oxygen from Regolith

The Carbothermal Reduction Demonstration (CaRD) project was an effort to develop a prototype system to demonstrate the extraction of oxygen from simulated lunar regolith using concentrated solar energy and a carbothermal reaction. The prototype consisted of a deployable solar concentrator capable of tracking the sun, carbothermal reactor, fluid system, gas analysis, and a solar concentrator control system consisting of avionics and software. These subsystems were developed by multiple NASA centers and a private industry partner, Sierra Space. The various teams worked together to define requirements and interfaces to successfully assemble the complex system and demonstrate an integrated solar carbothermal process. The solar concentrator developed at Glenn Research Center (GRC) was designed to be stowed for a launch environment then deployed on the lunar surface. It utilized a crossed dragone configuration of composite mirrors to direct horizontal sunlight onto a target 90° from the incoming sunlight. The key performance parameters for the solar concentrator were efficiency and power density. The carbothermal reactor was developed by Sierra Space through a separate project called the Carbothermal Oxygen Production Reactor (COPR) where it successfully demonstrated a fully automated process in a thermal vacuum environment. The fluid system needed for the carbothermal reaction was also developed by Sierra Space and successfully demonstrated in the same thermal vacuum test. The gas analysis system was developed at Kennedy Space Center (KSC) and was required to determine the amount of oxygen extracted during each test. The gas analysis system was based on the Mass Spectrometer Observing Lunar Operations (MSOLO) instrument. Avionics and software for the CaRD prototype were also developed at KSC and based on experience with MSOLO avionics and software. The control system was designed to stow, deploy, track the sun, and perform beam alignment of the concentrated light. The prototype subsystems were integrated and tested at Johnson Space Center’s (JSC) Energy Systems Test Area. A heliostat was used to direct sunlight toward the prototype in a way that is representative of the sunlight conditions at the south pole of the Moon. When concentrated sunlight was focused on simulated lunar regolith within the reactor, the gas analysis team confirmed the presence of carbon monoxide gas, which confirmed that a solar carbothermal reaction took place. The key performance parameter for the integrated prototype was grams of oxygen extracted per kilowatt hour of energy arriving at the concentrator primary mirror. The prototype design successfully demonstrated end-to-end capability and further steps to achieve a flight capable system have been defined. With lunar data, engineers would be able to design a scaled-up system capable of extracting oxygen from regolith at useful quantities for crew life support and rocket propellant. On the long term, this method of In-Situ Resource Utilization could be used to drastically reduce the cost and risk of a sustained human presence on the Moon by reducing the amount of oxygen that would have to be delivered.

Oxygen from Regolith↗

NASA NTRS2026

Prototype Demonstration of Solar Carbothermal System to Extract Oxygen from Regolith

The Carbothermal Reduction Demonstration (CaRD) project was an effort to develop a prototype system to demonstrate the extraction of oxygen from simulated lunar regolith using concentrated solar energy and a carbothermal reaction. The prototype consisted of a deployable solar concentrator capable of tracking the sun, carbothermal reactor, fluid system, gas analysis, and a solar concentrator control system consisting of avionics and software. These subsystems were developed by multiple NASA centers and a private industry partner, Sierra Space. The various teams worked together to define requirements and interfaces to successfully assemble the complex system and demonstrate an integrated solar carbothermal process. The solar concentrator developed at Glenn Research Center (GRC) was designed to be stowed for a launch environment then deployed on the lunar surface. It utilized a crossed dragone configuration of composite mirrors to direct horizontal sunlight onto a target 90° from the incoming sunlight. The key performance parameters for the solar concentrator were efficiency and power density. The carbothermal reactor was developed by Sierra Space through a separate project called the Carbothermal Oxygen Production Reactor (COPR) where it successfully demonstrated a fully automated process in a thermal vacuum environment. The fluid system needed for the carbothermal reaction was also developed by Sierra Space and successfully demonstrated in the same thermal vacuum test. The gas analysis system was developed at Kennedy Space Center (KSC) and was required to determine the amount of oxygen extracted during each test. The gas analysis system was based on the Mass Spectrometer Observing Lunar Operations (MSOLO) instrument. Avionics and software for the CaRD prototype were also developed at KSC and based on experience with MSOLO avionics and software. The control system was designed to stow, deploy, track the sun, and perform beam alignment of the concentrated light. The prototype subsystems were integrated and tested at Johnson Space Center’s (JSC) Energy Systems Test Area. A heliostat was used to direct sunlight toward the prototype in a way that is representative of the sunlight conditions at the south pole of the Moon. When concentrated sunlight was focused on simulated lunar regolith within the reactor, the gas analysis team confirmed the presence of carbon monoxide gas, which confirmed that a solar carbothermal reaction took place. The key performance parameter for the integrated prototype was grams of oxygen extracted per kilowatt hour of energy arriving at the concentrator primary mirror. The prototype design successfully demonstrated end-to-end capability and further steps to achieve a flight capable system have been defined. With lunar data, engineers would be able to design a scaled-up system capable of extracting oxygen from regolith at useful quantities for crew life support and rocket propellant. On the long term, this method of In-Situ Resource Utilization could be used to drastically reduce the cost and risk of a sustained human presence on the Moon by reducing the amount of oxygen that would have to be delivered.

Aaron Paz↗

NASA NTRS2025

Beamed Energy and Communications Optical Node (BEACON) Demonstrator

Due to long shadow periods (2 weeks or greater) on the south pole, concepts to raise solar arrays to a sufficient height at specific locations have shown the capability to provide power to surface users for much longer periods. Such a tower can also provide a 3rd Generation Partnership Project (3GPP) service for users up to 10 km away, dependent on terrain. An option to deliver power, albeit with low efficiency, using a laser beam coupled with the tower height could provide mobile and fixed users power during darkness, reducing their battery requirements. A demonstration of these technologies in the lunar environment is crucial to support future Artemis campaigns as well as potential emerging lunar infrastructures. A demonstrator design of a 15 m deployed boomon the south pole has been shown to enable both the gathering of kilowatts of power and the provision of 3GPP relay and backhaul given an appropriate lunar location. Using a laser to send power to a photovoltaic receiver has been proposed to transmit electrical power on the moon, particularly for applications such as powering a rover in near-polar permanently shadowed regions (PSR) where solar power is not available. In this work, the Compass team performed a conceptual engineering design study of a near-term laser surface-to-surface power beaming and relay station using a tower to simultaneously carry the power source (Vertical Solar Array Technologies (VSAT)[1]), the 3GPP relay antenna, and the laser telescope.

Deployable solar array tower laser beamed power 3G↗

NASA NTRS2022

Titan In-situ Resource Utilization (ISRU) Sample Return (TISR)

Titan is unique in the outer solar system in that it is the only moon with a thick atmosphere, and the only body in the solar system outside the Earth with liquid seas on its surface. The Titanian oceans, however, are seas of liquid hydrocarbons, and the rocks on the surface are solid water ice. Like other icy Moons of the outer solar system, beneath the ice crust, Titan also has a subsurface ocean. Rodriguez et al. refer to it as the “world with two oceans”, an organic-rich body with interior-surface-atmosphere interactions that are comparable in complexity to the Earth. [1] Titan is scientifically fascinating in many ways [2], [3], [4]. The Compass Team will emphasize just one here: Titan is a high priority target for astrobiology [4] [5] [6] [7] [8] [9] [10] [11]. It is a world with a surface and atmosphere rich in the complex organic compounds known as tholins. A detailed understanding of the nature of these complex compounds will require an analysis using a full laboratory on Earth. Because of its value to understanding the organic compounds of the outer solar system which may be the primordial building-blocks of life, return of samples from Titan to laboratories on Earth will be the primary goal of this mission. While this would give unprecedented science return, returning even a small sample from Titan using conventional technology would be tremendously difficult. Saturn is almost a billion miles from the Earth, about thirteen times farther than Mars. A return mission to Saturn requires such a large total-mission ∆V that, with conventional technology, the mass ratios required are prohibitive. Such a sample return would truly be “mission incredible.” But to date, a sample return mission from so distant a target has been assumed to be, not merely incredible, but mission impossible. The Compass Team has proposed [2] [12] that by manufacturing the propellant for the return to Earth using the resources available on Titan, such a mission becomes possible. The task of this report is to show that it is reasonable with credible space technology.

Titan↗

NASA NTRS2022

RHU-RPS Long Duration Mars Hard Lander: Meteorology and Seismology Enabled by Radioisotopes (MASER)

Compass Team was tasked by the RPS Project at the NASA Glenn Research Center (GRC) to create an independent concept design for a spacecraft (S/C) utilizing low power radioisotope power. A list of candidate missions enabled by milliwatt class radioisotope power was evaluated and thus resulted in the selection of a Mars polar region seismology network of four hard landers. A science rational and science operations plan was developed to establish mission design requirements and S/C subsystem concept designs described herein.

RPS↗

NASA NTRS2022

40kW Fission Surface Power System (FSPS) Deployability

Continuous power at the kilowatt level will be imperative for future lunar users including crew infrastructure, future science, and in-situ resource utilization (ISRU). The Compass Team explored both 10 kilowatt electric (kWe) and 40 kWe concepts, assuming planned lander and rover capabilities. Both concepts found that a crew pressurized rover chassis, repurposed for deploying reactor power components, could place a fission surface power system (FSPS) at least one kilometer from users. While the 10 kWe fission power system (FPS) could be deployed as a single unit, the 40 kWe system was too large and had to be deployed in multiple trips with the same rover. Key technologies and design approaches included a high-assay low-enriched uranium (HALEU), yttrium hydride (YH) moderated heat pipe reactor, Stirling convertors, deployable radiators based on International Space Station (ISS) designs, and power conversion/transmission at ±2800 volts of direct current (VDC).

Lunar reactor 40kW fission deployable↗

NASA NTRS2021

Numerical Modeling and Design of Gaseous Propellant Acquisition System for the Triton Hopper

Triton, the largest moon around Neptune, is a captured Kuiper Belt Object with a dynamic rarified atmosphere, active geysers, and unique “cantaloupe” like terrain. Little is known about Kuiper Belt Objects in the scientific community with most of the information coming from Pluto. Currently, NASA is designing an unmanned probe to explore the atmosphere and surface of Triton. This vehicle is unique in that it repeatedly takes off and lands (hops) using nitrogen propellant collected from its surroundings on Triton. This paper presents preliminary conceptual system design and numerical modeling of the atmospheric collection process. Four concepts are presented: a cryocooler-based system, a pump-based system, a sublimation and pump-based system, and a cryocooler and sublimation system. Numerical modeling takes into account the mass and energy transfer between all the relevant nodes in the system and is able to calculate the amount of nitrogen ice collected and ice accumulation rate as a function of time for each concept. The models are ultimately used to assess the feasibility of traversing from equator to pole in under two years using a gaseous propellant acquisition system for the Hopper.

Hopper↗

NASA NTRS2020

Advanced Modular Power System Fully Populated Electronics Enclosure Thermal Testing

A thermal test of an enclosure housing the AMPS electronics cards was performed. The enclosure was fully populated with 17 nonfunctioning AMPS electronics cards. Heaters were applied to the cards to simulate their operation. A cold plate was installed on the top of the case. The case was then insulated to simulate its installation within an electronics rack with the face and rear of the enclosure left open. The cold plate was connected to a chiller which provided cooling water at a fixed input temperature to the cold plate. Flow rates from the chiller of 0.0 L/min, 1.4 L/min and 1.8 L/min were tested. The test was operated at each flow rate over a range of heater power levels until the steady state temperature of the electronics cards was reached. Heater power levels from 2.5 W/card to 45 W/card were tested. The data collected was used to determine the steady state operating temperature of the cards, the temperature distribution between the cards, the time to reach steady-state temperature, the change in steady state temperature with change in heater power, the temperature distribution between the cards at the steady state condition and the heat lost to the surrounds by the enclosure. One of the main goals of the testing was to determine how much waste heat the cards could generate and still maintain a touch temperature at or below 40°C. Based on this requirement, for the 3 cooling rates tested, the maximum card waste heat that could be generated by each individual card was 3.9 W, 16.3 W and 17.6 W respectively. An analysis was also set up to provide an analytical model to estimate the card temperature under different cold plate flow rates and card heater power levels. The results off the analysis was compared to that of the experiment of the range of flow rates and power levels tested.

Anthony Colozza↗

NASA NTRS2020

Compass Final Report: Venus Bridge Orbiter and Surface Study (V-BOSS)

The Venus Bridge Orbiter and Surface Study (V-BOSS) Compass concurrent engineering design team study shows that new, high-priority Venus science can be achieved using a linked Orbiter + Surface Element (Lander) mission concept within a $200M cost cap with assumptions. This is feasible through optimizing investment in early technologies and platforms, such as the Long-Lived In-Situ Solar System Explorer (LLISSE), leveraging known and flight-ready technology, and the overall use of simple, small, robust systems in innovative approaches to Venus exploration. This architecture allows a range of science investigations through modification of Orbiter-Lander platforms in this study through choice of other instruments (often sensors), science themes, or operational modes. In particular, a fundamental strength of this approach is to provide science not available in other ways by using simplified architectures including rugged systems operable in-situ on the Venus surface. Such investigations would be pathfinders for more complex, and more expensive, future missions. Additionally, the results of this study can be used to further champion the need, value and return of early investment technology programs for the hard problem of in-situ investigations at Venus.

Venus Bridge↗

NASA NTRSDate not supplied

Mars Opposition Piloted Nuclear Electric Propulsion (NEP)-Chem Vehicle

Many previous studies have examined sending crews to and from Mars. The most economical involved a ‘conjunction’ class whereby the crew spends around 500 days on Mars surface waiting for a ‘cheap’ return. The total mission time results in a mission duration around 3 years. Given the current demonstrated crew maximum of a 1 year stint on ISS, it is interesting to look at reducing that time to only two years, thus reducing risk and minimizing time in the Martian System. In order to meet such a short mission an ‘opposition’ class Mars mission (which includes a Venus flyby) was chosen. The energy required to perform such a mission in only two years (for the 2036 opportunity at least) is about three times that of the 3 year conjunction mission. The rocket equation clearly shows that this mission would then require several times the propellant of the three-year mission unless the Isp of the propulsion system can be increased. Electric propulsion can provide the 3-10x improvement in Isp but even with a nuclear reactor power levels could approach 10 MWe. As an alternative, a smaller reactor (1.5 MWe class) joined together with a chemical stage was found to allow for using each propulsion system to its best advantage: low thrust in interplanetary space and chemical in the gravity wells of Earth and Mars. Indeed, the use of high Isp, low thrust during the interplanetary leg of the journey’s reduced the required capture/departure ∆Vs by 5-10X. Lowering the NEP power also allowed fitting the power system into a single SLS launch – which limited the radiator area to ~ 2500m^2. For the first look a reactor using fuels created by the SP-100 program with a limit of ~1200K was assumed. Starting in the ‘Lunar Gateway’ also allowed for use of commercial tankers to fuel the vehicle in a relative benign place. A top level summary of the mission design, concept of operations, as well as a conceptual point design of the vehicle is described.

Nuclear Electric Propulsion↗

NASA NTRSDate not supplied

Use of a Dynamic Radioisotope Power Source for a Long Duration Lunar Science Rover

The Radioisotope Power Systems (RPS) Program tasked the Compass Team to evaluate use of Dynamic Radioisotope Power Sources (DRPS) for lunar science rovers. The object was to identify their advantages and challenges as well as to influence the technology developments with flight-type requirements. This was done by using the promising Volatiles Investigating Polar Exploration Rover (VIPER) solar-powered rover mission as a platform to ‘swap in’ a DRPS. The resulting design used a ‘pickup truck bed’ approach which allowed simplified installation and operation of the DRPS while also keeping the forward lunar surface ‘blocked’ from the DRPS waste heat, which could sublimate the icy surface. It was found that with the Stirling DRPS option the mass is within the planned VIPER lander capability and is comparable to VIPER mass and size (the DRPS replaces large battery pack/solar arrays). The Stirling DRPS option produced ~300 Watts electrical (We) using six general purpose heat source (GPHS) bricks and eight Stirling convertors. Replacing the solar/battery power with radioisotope power allows a continuous presence (instead of six hours) in a permanently shadowed region (PSR) and over 18 months of operations with minimal science impact (rearward surface heating). It was also found that use of a dynamic system, instead of a thermoelectric system, reduces the heat impact on the science environment two-to-three times while still providing sufficient waste heat for the rover systems in the PSR (~ -200°C). The DRPS, along with a relay link (like Gateway), can provide extended access to PSR. The system was also found to be capable of roving for eight hours per day with a range of well over 100 km in 18 months.

Radioisotope Power↗

NASA NTRSDate not supplied

A Deployable 40 kWe Lunar Fission Surface Power Concept

Continuous power at the kilowatt level will be imperative for future lunar users including crew infrastructure, future science, and in-situ resource utilization (ISRU). The Compass Team explored both 10 kWe and 40 kWe concepts, assuming planned lander and rover capabilities. Both concepts found that a crew pressurized rover chassis, repurposed for deploying reactor power components, could place a fission surface power system (FSPS) at least one km from users. While the 10 kWe fission power system (FPS) could be deployed as a single unit, the 40 kWe system was too large and had to be deployed in multiple trips with the same rover. Key technologies and design approaches included a high-assay low-enriched uranium (HALEU), yttrium hydride (YH) moderated heat pipe reactor, Stirling convertors, deployable radiators based on International Space Station (ISS) designs, and power conversion/transmission at ±2800 VDC for a one km remote distance.

Fission Power↗

NASA NTRSDate not supplied

1.9 MWe Nuclear Electric Propulsion-Chemical Propulsion Piloted Mars Opposition Vehicle

To assess ‘quick’ missions to Mars, a study was performed to determine the feasibility of a two-year roundtrip class mission concept of operation that enables boots on Mars in the 2030s. After performing a Phase 1.1 2036 Mars opposition design case, the more difficult 2039 opposition design was pursued. This Phase 1.2 also sought to further refine the concept, building on feasibility, and addressing several challenges brought by independent team reviews. Given the date of 2039, nearer-term technologies, primarily nuclear thermal and nuclear electric were deemed as the most viable for these missions. This paper explores a nuclear electric and chemical combined propulsion approach to achieve the desired mission timeline.

Nuclear Electric Propulsion↗

NASA NTRSDate not supplied

Lunar Surface Relay - Mobile: Concept to Provide Relay Links to Surface Assets

At the request of NASA’s Space Communication and Navigation (SCaN) program, the Glenn Research Center’s (GRC) Compass concurrent engineering team developed a conceptual design of a Lunar Surface Relay- Mobile (LSR-M) system to provide a variety of surface and relay communication links in support of future Artemis sorties. The team determined that a mobile asset, with its ability to relocate to support a variety of surface sites and leverage more hospitable winter locations on the lunar south pole, would be of particular use in the architecture. Following the design of a solar array and battery powered baseline case, a quick look design further investigated adding a multi-mission radioisotope thermoelectric generator (MMRTG) to the system to reduce battery requirements to survive the lunar night and remove the need to relocate to favorable night locations during the lunar winter.

Lunar Surface Relay↗

NASA NTRSDate not supplied

A 1 MW Solar Electric and Chemical Propulsion Vehicle for Piloted Mars Opposition Class Missions

Previous investigations have extensively explored crew missions to and from Mars, with a prevailing approach termed the 'conjunction' class, necessitating an approximately 500-day stay at Mars for a cost-effective return. However, this configuration results in a mission duration exceeding 1000 days (roughly 3 years). In order to reduce crew health and surface operations risks, a shortened mission duration of 850 days is being explored by using a short ~30 day Mars surface stay and a ‘opposition’ class approach. A non-nuclear approach is possible by combining solar electric propulsion and a chemical stage. While past mission concepts for the conjunction missions also used solar electric propulsion they limited the SEP power to <700 kW. In order to achieve the 850 day round trip more SEP power is needed. A 1MW class SEP-Chem vehicle was found sufficient to perform the 850 day mission. The biggest challenge for the design will be the large, high power solar arrays, mainly from their deployment and stability. This work describes the design of the SEP-Chem vehicle, assembled in a Near Rectilinear Halo Orbit (NRHO) and employing super-heavy class and the Space Launch System (SLS) launchers.

SEP-Chem↗

NASA NTRSDate not supplied

Kiloton Class ISRU Systems for LO2/LCH4 Propellant Production on the Mars Surface

As part of the 2023 strategic analysis cycle to explore the trade space, the NASA Mars Architecture Team wanted to explore what it takes to produce in situ on Mars many hundreds of tons of propellants for a large all-chemical transportation system. The conceptual operations and design of the LO 2 /LCH 4 in situ resource utilization (ISRU) water acquisition, propellant production and liquification system was assigned to the NASA Compass concurrent engineering team with support from various NASA ISRU, cryogenic fluid management, and surface power experts. The conceptual point design examined one case producing 300 t of LO 2 /LCH 4 from the Mars atmosphere and delivered water in 20 months and storing the liquified propellants in a to-be-reused lander. Several of these large single-stage, all-chemical class large vertical landers would deliver the required ISRU equipment. The required 150 t of water stock for the ISRU system was traded between three options: delivered, pumped from subsurface ice deposits or extracted from surface soils. The large propellant production systems consist of atmospheric CO 2 collection scroll pumps, a combined solid oxide electrolysis and methanation system to convert the CO 2 and water into gaseous O 2 and CH 4 , and various dryers, scrubbers, and separators to remove the excess water, CO 2 and H 2 . The liquefaction system consisted of 90 K cryocoolers to provide cold Ne to the launch vehicle tanks to liquify these CH 4 and O 2 gases and store them as rocket propellants. The systems are deployed using a 6 t (payload) capable chassis derived from conceptual pressurized rover designs. In total, the propellant production and liquefaction systems required three propellant production pallets, two liquefaction pallets, two water tankers, and six 40 kW-fission surface power systems (FSPS) with cabling. All this equipment was found to notionally fit inside two- 75 metric ton payload capacity Mars ascent and landing vehicles (MALV). For the case where 150 t of water delivered from Earth, four cargo MALVs are required for the full system. The same is true when the 150 t of water is extracted through surface mining. For the borehole system, only 3 cargo MALVs are necessary. A comparison of approaches in terms of number of landers, number and type of elements, power and time is made.

ISRU↗

NASA NTRSDate not supplied

Power Beaming from Lunar Orbit for Small Science Landers

A proposal for future small science mission to the moon envisions a network of small landers spread across the lunar surface, at latitudes ranging from equatorial to near polar landing sites. To provide power across the lunar nighttime, when solar power is not available, we analyze a proposal to power such small landers from orbit, using a laser to direct power from an orbital power station to photovoltaic arrays on the landers that are tuned to the laser wavelength. The approach is seen to be feasible, and conops for the system were outlined and a design for the spacecraft put together. To provide power to landers at any location, three orbital stations are required, each carrying a 3-kW laser.

Power Beaming↗

NASA NTRSDate not supplied

A Conceptual Architecture for Venus Surface Sample Return

A conceptual architecture for retrieval of a sample of the surface of Venus is proposed. The mission concept incorporates a high-temperature aircraft to retrieve the sample from the surface and raise it into the upper atmosphere, a balloon-borne platform to produce fuel from the carbon dioxide atmosphere of Venus, and a launch vehicle to bring the sample into Venus orbit, where it is retrieved by an Earth-return vehicle.

Venus↗