Engineering Papers⌕ Search

Engineering topics

Anderson, G. Y.

Publications and source records attributed to Anderson, G. Y..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Study of hypersonic inlet flow fields with a three-dimensional Navier-Stokes code

A three-dimensional Navier-Stokes code is used to study the flow through an inlet with a rectangular capture area, but with circular or essentially circular internal cross-sections. The inlet may have a center body extending partially or fully over the length of the inlet. Calculations are made under a variety of geometrical constraints imposed on the inlet cross-sections to study the flow quality in the inlet. It is observed that for this class of inlets, the boundary layer has a tendency to thicken and separate readily due to the adverse pressure gradient caused by the continuous compression in the inlet. Since no experimental results are yet available, this paper has presented only the numerical results from the present analysis.

Kumar, A.↗
NASA NTRS1986

Survey of supersonic combustion ramjet research at Langley

The Hypersonic Propulsion Branch at NASA Langley Research Center has maintained an active research program in supersonic combustion ramjet (scramjet) and high speed ramjet propulsion since the 1960s. The focus for this research has centered on propulsion for manned reuseable vehicles with cryogenic hydrogen fuel. This paper presents some highlights of this research. The design philosophy of the Langley fixed-geometry airframe-integrated modular scramjet is discussed. The component development and research programs that have supported the successful demonstration of the engine concept using subscale engine module hardware is reviewed and a brief summary of the engine tests presented. An extensive bibliography of research supported by the Langley program is also included.

Northam, G. B.↗
NASA NTRS1980

Evaluation of a bulk calorimeter and heat balance for determination of supersonic combustor efficiency

Results are presented from the shakedown and evaluation test of a bulk calorimeter. The calorimeter is designed to quench the combustion at the exit of a direct-connect, hydrogen fueled, scramjet combustor model, and to provide the measurements necessary to perform an analysis of combustion efficiency. Results indicate that the calorimeter quenches reaction, that reasonable response times are obtained, and that the calculated combustion efficiency is repeatable within + or -3 percent and varies in a regular way with combustor model parameters such as injected fuel equivalence ratio.

Mcclinton, C. R.↗
NASA NTRS1978

Characterization of a swept-strut hydrogen fuel-injector for scramjet applications

Results of an experimental investigation of a swept-strut hydrogen fuel-injector simulating the center strut of a three strut scramjet module at Mach 6 flight conditions are presented. Detailed wall pressure distributions from over 100 separate tests with overall fuel flow from 0.1 to 1.3 times stoichiometric and test gas stagnation temperature from 1100 to 2400 K were recorded. The distance for pressure rise from the point of injection was found to increase with increasing test stagnation temperature. This trend indicates that chemical kinetics in the immediate region of perpendicular injection are not likely to be the mechanism controlling the onset of pressure rise. A fluid dynamic mechanism is suggested involving separation of the boundary layer downstream of injection which is forced upstream from the trailing edge by pressure rise due to combustion occurring in the base region of the strut. The results obtained indicate that the swept-strut fuel-injector concept can be adapted to a wide range of flight conditions by varying the amount of perpendicular fuel injection.

Northam, G. B.↗
NASA NTRS1977

Experimental investigation of a swept-strut fuel-injector concept for scramjet application

Results are presented of an experiment to investigate the behavior at Mach 4 flight conditions of the swept-strut fuel-injector concept employed in the Langley integrated modular scramjet engine design. Autoignition of the hydrogen fuel was not achieved at stagnation temperatures corresponding to a flight Mach number of 4; however, once ignition was achieved, stable combustion was maintained. Pressure disturbances upstream of the injector location, which were caused by fuel injection and combustion, were generally not observed; this indicates the absence of serious adverse combustor-inlet interactions. Mixing performance and reaction performance determined from probe surveys and wall pressure data indicate that high combustion efficiency should be obtained with the combustor length provided in the scramjet engine design. No adverse interaction between the perpendicular and parallel fuel-injection modes was observed.

Anderson, G. Y.↗
NASA NTRS1977

Premixed flame propagation characteristics in a supersonic airstream

Measured values of flame angles are presented to aid the design of premixed combustion chambers and prediction of flame propagation. Flame spread, velocity, and dependence of burning rate on the properties of unburned flow and on turbulence levels are compared with the measured values. The premixed flame angle is found proportional to the amount of heat released, and correlates readily with the fuel mixture ratio through the rate of heat release or rate of water formation. Finite rate combustion affects flame angle mostly at off-stoichiometric conditions. The pilot affects the flame angle if abundant unburnt fuel is present in the pilot hot gases. Viscosity runs several times over the rated level.

Agnone, A. M.↗
NASA NTRS1976

Supersonic combustion ramjet /scramjet/ engine development in the United States

This survey of supersonic combustion ramjet (scramjet) engine development in the United States covers development of this unique engine cycle from its inception in the early 1960's through the various programs currently being pursued and, in some instances, describing the future direction of the programs. These include developmental efforts supported by the U.S. Navy, National Aeronautics and Space Administration, and U.S. Air Force. Results of inlet, combustor, and nozzle component tests, free-jet engine tests, analytical techniques developed to analyze and predict component and engine performance, and flight-weight hardware development are presented. These results show that efficient scramjet propulsion is attainable in a variety of flight configurations with a variety of fuels. Since the scramjet is the most efficient engine cycle for hypersonic flight within the atmosphere, it should be given serious consideration in future propulsion schemes

Waltrup, P. J.↗
NASA NTRS1975

Supersonic Mixing and Combustion in Parallel Injection Flow Fields

Adequate prediction techniques for supersonic, mixing, reacting flows are of great importance in the design and performance analysis of supersonic combustion ramjet (scramjet) engines. Analytical programs for parallel injection flow fields with chemical reaction and turbulent mixing are now available for both single and multiple-jet flows. The application of these analyses to simple flow geometries is discussed, and comparisons also are made with data on the more complex case of multiple-jet, reacting flows. A review is given of Langley investigations of parallel injection flow fields. Among these are single-jet studies of nonreacting, turbulent mixing (H2 in air and H2 in N2), and of reacting turbulent mixing (H2 in air) with both single and multiple jets. Implications of the results of the studies for scramjet fuel injector design are discussed.

Evans, J. S.↗
NASA NTRS1975

Hypersonic propulsion

The NASA research on scramjet technology for speeds above Mach 5 is reported. A brief overview of the NASA Hypersonic Research Engine (HRE) project is presented with emphasis on the most significant contributions on the HRE to scramjet technology. The work on high-performance airframe-integrated scramjet engines is described, and a new versatile research airplane is discussed with emphasis on propulsion.

Anderson, G. Y.↗
NASA NTRS1974

Exploratory tests of two strut fuel injectors for supersonic combustion

Results of supersonic mixing and combustion tests performed with two simple strut injector configurations, one with parallel injectors and one with perpendicular injectors, are presented and analyzed. Good agreement is obtained between static pressure measured on the duct wall downstream of the strut injectors and distributions obtained from one-dimensional calculations. Measured duct heat load agrees with results of the one-dimensional calculations for moderate amounts of reaction, but is underestimated when large separated regions occur near the injection location. For the parallel injection strut, good agreement is obtained between the shape of the injected fuel distribution inferred from gas sample measurements at the duct exit and the distribution calculated with a multiple-jet mixing theory. The overall fraction of injected fuel reacted in the multiple-jet calculation closely matches the amount of fuel reaction necessary to match static pressure with the one-dimensional calculation. Gas sample measurements with the perpendicular injection strut also give results consistent with the amount of fuel reaction in the one-dimensional calculation.

Anderson, G. Y.↗
NASA NTRS1974

An examination of injector/combustor design effects on scramjet performance

Description of a simplified one-dimensional treatment of fuel injection for supersonic combustor performance analysis. Representative mixing efficiency variations for both parallel and cross-stream injection are obtained, and approximate means for estimating the length required for complete mixing are demonstrated. Comparisons of calculated and measured data show good agreement.

Anderson, G. Y.↗
NASA NTRS1973

Design considerations for the airframe-integrated scramjet

Research programs at the NASA Langley Research Center on the development of airframe-integrated scramjet concepts (supersonic combustion ramjet) are reviewed briefly. The design and performance of a specific scramjet configuration are examined analytically by use of recently developed and substantiated techniques on boundary-layer development, heat transfer, fuel-air mixing, heat-release rates, and engine-cycle analysis. These studies indicate that the fixed-geometry scramjet module will provide practical levels of thrust performance with low cooling requirements. Areas which need particular emphasis in further development work are the combustor design for low speeds and the integrated nozzle design.

Henry, J. R.↗