Engineering Papers⌕ Search

Engineering topics

Anders, Andre

Publications and source records attributed to Anders, Andre.

61 records · Page 4

Plasma"anti-assistance" and"self-assistance" to high power impulse magnetron sputtering

A plasma assistance system was investigated with the goal to operate high power impulse magnetron sputtering (HiPIMS) at lower pressure than usual, thereby to enhance the utilization of the ballistic atoms and ions with high kinetic energy in the film growth process. Gas plasma flow from a constricted plasma source was aimed at the magnetron target. Contrary to initial expectations, such plasma assistance turned out to be contra-productive because it led to the extinction of the magnetron discharge. The effect can be explained by gas rarefaction. A better method of reducing the necessary gas pressure is operation at relatively high pulse repetition rates where the afterglow plasma of one pulse assists in the development of the next pulse. Here we show that this method, known from medium-frequency (MF) pulsed sputtering, is also very important at the much lower pulse repetition rates of HiPIMS. A minimum in the possible operational pressure is found in the frequency region between HiPIMS and MF pulsed sputtering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ion Generator

Andre Anders, at Lawrence Berkeley National Laboratory, speaks about magnetron sputtering, a technology used for thin films.

74 ATOMIC AND MOLECULAR PHYSICS↗

Ion Generator

Andre Anders discuss magnetron sputtering which is a technology used for fin films.

36 MATERIALS SCIENCE↗

Evolution of the plasma composition of a high power impulse magnetron sputtering system studied with a time-of-flight spectrometer

The plasma of a high power impulse magnetron sputtering (HiPIMS) system has been investigated using a time-of-flight (TOF) spectrometer. The target materials included high sputter yield materials (Cu, Ag), transition metals (Nb, Cr, Ti), and carbon (graphite); the sputtering gases were argon, krypton and nitrogen, and two different target thicknesses were selected to consider the role of the magnetic field strength. Measurements for selected combinations of those parameters give quantitative information on the transition from gas-dominated to metal-dominated (self-sputtering) plasma, on the fractions of ion charge states, and in the case of molecular gases, on the fraction of atomic and molecular ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Physical limits for high ion charge states in pulsed discharges in vacuum

Short-pulse, high-current discharges in vacuum were investigated with the goal to maximize the ion charge state number. In a direct extension of previous work [Appl. Phys. Lett. 92, 041502 (2008)], the role of pulse length, rate of current rise, and current amplitude was studied. For all experimental conditions, the usable (extractable) mean ion charge state could not be pushed beyond 7+. Instead, a maximum of the mean ion charge state (about 6+ to 7+ for most cathode materials) was found for a power of 2-3 MW dissipated in the discharge gap. The maximum is the result of two opposing processes that occur when the power is increased: (i) the formation of higher ion charge states, and (ii) a greater production of neutrals (both metal and non-metal), which reduces the charge state via charge exchange collisions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Self-sputtering far above the runaway threshold: an extraordinary metal ion generator

When self-sputtering is driven far above the runaway threshold voltage, energetic electrons are made available to produce"excess plasma" far from the magnetron target. Ionization balance considerations show that the secondary electrons deliver the necessary energy to the"remote" zone. Thereby, such a system can be an extraordinarily prolific generator of useable metal ions. Contrary to other known sources, the ion current to a substrate can exceed the discharge current. For gasless self-sputtering of copper, the useable ion current scales exponentially with the discharge voltage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A theoretical analysis of vacuum arc thruster performance

In vacuum arc discharges the current is conducted through vapor evaporated from the cathode surface. In these devices very dense, highly ionized plasmas can be created from any metallic or conducting solid used as the cathode. This paper describes theoretical models of performance for several thruster configurations which use vacuum arc plasma sources. This analysis suggests that thrusters using vacuum arc sources can be operated efficiently with a range of propellant options that gives great flexibility in specific impulse. In addition, the efficiency of plasma production in these devices appears to be largely independent of scale because the metal vapor is ionized within a few microns of the cathode electron emission sites, so this approach is well-suited for micropropulsion.

thruster↗