Engineering topics
Publications and source records attributed to Anagnostou, E..
In this paper we present results from the application of a satellite infrared (IR) technique for estimating rainfall over northern South America. Our main objectives are to examine the diurnal variability of rainfall and to investigate the relative contributions from the convective and stratiform components. Additional information is contained in the original.
Electrical connections to solar cells in a module are made at the same time the cells are encapsulated for protection. The encapsulating material is embossed to facilitate the positioning of the cells during assembly.
To determine lifetimes of the first generation (Block 1) commercial solar cell modules used in solar cell arrays, a program was initiated to expose these modules to a range of environments. The conditions endured by these modules encompassed hot and dry, hot and humid, tropical rain forests, sea-air, urban industrial and urban clean. Exposures were for periods up to 1 year. The effect of outdoor exposure on the performance of the modules was determined using current-voltage curves. Short-circuit current (I sub sc) and maximum power (P sub max) were the parameters monitored. In all cases, there was a loss of performance of the modules with outdoor exposure.
Materials for solar-cell module construction have been studied on the basis of limited real-time outdoor exposure evaluations. The materials tested included transmission samples, sub-modules, and actual solar cells. The results suggest that glass, fluorinated ethylene propylene, and perfluoroalkoxy are good materials for the covering or encapsulation of solar-cell modules. In all cases, dirt accumulation and cleanability are important factors.
NASA-LeRC has conducted outdoor endurance tests on modules commercially produced as part of the 46-kW purchase of first generation (Block I) modules by the JPL Low Cost Silicon Solar Array Project. Block I modules from four manufacturers were installed at commercial testing sites in Florida, Puerto Rico, and Arizona and at noncommercial sites in Cleveland, Ohio. The conditions endured by these modules included hot and dry, hot and humid, tropical rain forest, sea-air, urban industrial and urban clean; exposures were for periods up to one year. Test results are presented and discussed.
Real-time and accelerated outdoor endurance testing was performed on a variety of samples of interest to the National Photovoltaic Conversion Program. The real-time tests were performed at seven different sites and the accelerated tests were performed at one of those sites in the southwestern United States. The purpose of the tests were to help evaluate the lifetime of photovoltaic systems. Three types of samples were tested; transmission samples of possible cover materials, sub-modules constructed using these materials attached to solar cells, and solar cell modules produced by the manufacturers for the ERDA program. Results indicate that suitable cover materials are glass, FEP-A and PFA. Dirt accumulation and cleanability are important factors in the selection of solar cell module covers and encapsulants.
Plastic samples and solar cell sub modules were exposed to an accelerated outdoor environment in Arizona and an accelerated simulated environment in a cyclic ultraviolet exposure tester which included humidity exposure. These tests were for preliminary screening of materials suitable for use in the manufacture of solar cell modules which are to have a 20-year lifetime. The samples were exposed for various times up to six months, equivalent to a real time exposure of four years. Suitable materials were found to be FEP-A, FEP-C, PFA, acrylic, silicone compounds and adhesives and possibly parylene. The method of packaging the sub modules was also found to be important to their performance.
Plastic samples, solar cell modules, and sub-modules were exposed at test sites in Florida, Arizona, Puerto Rico, and Cleveland, Ohio, in order to determine materials suitable for use in solar cell modules with a proposed 20-year lifetime. Various environments were encountered including subtropical, subtropical with a sea air atmosphere, desert, rain forest, normal urban, and urban-polluted. The samples were exposed for periods up to six months. Materials found not suitable were polyurethane, polyester, Kapton, Mylar, and UV-stabilized Lexan. Suitable materials were acrylic, FEP-A, and glass. The results of exposure of polyvinylidene fluoride were dependent on the specific formulation, but several types appear suitable. RTV silicone rubber (clear) appears to pick up and hold dirt both as a free film and as a potting medium for modules. The results indicate that dirt accumulation and cleanability are important factors in the selection of solar cell module covers and encapsulants.
Production expenses are decreased by embossing encapsulating plastic film to position and secure cells. Electric circuit is printed on plastic film simultaneously with cell encapsulation process. Procedure can be used with standard-contact and wraparound contact cells.
Samples of FEP-encapsulated silicon solar cells and various potential encapsulation or cover materials were subjected to both accelerated and real-time testing. The durability of the samples was determined by measuring changes in solar cell output or optical transmission as a function of exposure. The tests revealed some problem areas in the structural integrity of the materials, e.g., delamination and cracking in FEP. These problems were probably related to defects in fabrication. FEP and Aclar had the least transmission loss after accelerated exposure equivalents of 5 and 3 years, respectively.
Samples of FEP encapsulated silicon solar cells and various potential encapsulation or cover materials were subjected to accelerated and real time testing. By measuring changes in solar cell output or optical transmission as a function of exposure the durability of the samples was evaluated. Results are presented.
Solar cell performance and radiation resistance is improved by application of 1-mil thickness of Teflon FEP protective material. Cells produce 30 percent more power than similar cells with conventional Kapton covers.
Space radiation effects on plastic films used as cover materials on solar cells
Electron, proton and UV irradiation effects on CdS solar cell protective plastic films with or without adhesive coatings, measuring transmission changes
Transmission effects on plastic films irradiated with ultraviolet light in vacuum
Thermal radiation absorptance and vacuum outgassing characteristics of protective coatings
Ultraviolet radiation effects in vacuum on plastic films used as encapsulants for thin film cadmium sulfide solar cells
Stability of propane-oxygen flames at low pressures in turbulent flow