Engineering Papers⌕ Search

Engineering topics

An, Ke

Publications and source records attributed to An, Ke.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

An air-stable Na 3 SbS 4 superionic conductor prepared by a rapid and economic synthetic procedure

All-solid-state sodium batteries, using abundant sodium resources and solid electrolyte, hold much promise for safe, low cost, large-scale energy storage. To realize the practical applications of all solid Na-ion batteries at ambient temperature, the solid electrolytes are required to have high ionic conductivity, chemical stability, and ideally, easy preparation. Ceramic electrolytes show higher ionic conductivity than polymers, but they often require extremely stringent synthesis conditions, either high sintering temperature above 1000 C or long-time, low-energy ball milling. Herein, we report a new synthesis route for Na 3 SbS 4 , a novel Na superionic conductor that needs much lower processing temperature below 200 C and easy operation. This new solid electrolyte exhibits a remarkable ionic conductivity of 1.05 mS cm -1 at 25 °C and is chemically stable under ambient atmosphere. In conclusion, this synthesis process provides unique insight into the current state-of-the-art solid electrolyte preparation and opens new possibilities for the design of similar materials.

25 ENERGY STORAGE↗
DOE OSTI2016

In situ neutron scattering study of nanostructured PbTe-PbS bulk thermoelectric material

Nanostructures play an important role in thermoelectric materials. Their thermal stability, such as phase change and evolution at elevated temperatures, is thus of great interest to the thermoelectric community. In this study, in situ neutron diffraction was used to examine the phase evolution of nanostructured bulk PbTe-PbS materials fabricated using hot pressing and pulsed electrical current sintering (PECS). The PbS second phase was observed in all samples in the as-pressed condition. The temperature dependent lattice parameter and phase composition data show an initial formation of PbS precipitates followed by a redissolution during heating. The redissolution process started around 570 600 K, and completed at approximately 780 K. During cooling, the PECS sample followed a reversible curve while the heating/cooling behavior of the hot pressed sample was irreversible.

high temperature↗
DOE OSTI2016

Probing multiscale transport and inhomogeneity in a lithium-ion cells using in-situ neutron methods

Here, we demonstrate for the first time the lithiation process in graphitic anodes using insitu neutron radiography in a pouch cell format. The neutron absorption contrast shows a direct correlation between degree of lithiation and the discharge voltage plateau. Furthermore, we provide a semi-quantitative comparison between the observed spatial variations of neutron attenuation line profile across the graphite electrode and the calculated lithium concentration profiles computed under similar electrochemical discharge conditions. In conjunction, in situ neutron diffraction of a similar pouch cell under identical test protocol was carried to obtain information about the local phase changes upon lithiation. Combined in-situ radiography and diffraction opens up a powerful nondestructive method to understand the multi-scale nature of lithium transport and degradation in practical lithium-ion cells.

25 ENERGY STORAGE↗
DOE OSTI2015

Temperature-dependent phase-specific deformation mechanisms in a directionally solidified NiAl-Cr(Mo) lamellar composite

Phase-specific thermal expansion and mechanical deformation behaviors of a directionally solidified NiAl–Cr(Mo) lamellar in situ composite were investigated by using real-time in situ neutron diffraction during compression at elevated temperatures up to 800 °C. Tensile and compressive thermal residual stresses were found to exist in the NiAl phase and Crss (solid solution) phase, respectively. Then, based on the evolution of lattice spacings and phase stresses, the phase-specific deformation behavior was analyzed qualitatively and quantitatively. Moreover, estimates of phase stresses were derived by Hooke's law on the basis of a simple method for the determination of stress-free lattice spacing in in situ composites. During compressive loading, the NiAl phase yields earlier than the Crss phase. The Crss phase carries much higher stress than the NiAl phase, and displays consistent strain hardening at all temperatures. The NiAl phase exhibits strain hardening at relatively low temperatures and softening at high temperatures. During unloading, the NiAl phase yields in tension whereas the Crss phase unloads elastically. Additionally, post-test microstructural observations show phase-through cracks at room temperature, micro cracks along phase interfaces at 600 °C and intact lamellae kinks at 800 °C, which is due to the increasing deformability of both phases as temperature rises.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Understanding Low-cycle Fatigue Life Improvement Mechanisms in a Pre-twinned Magnesium Alloy

The mechanisms of fatigue life improvement by pre-twinning process in a commercial rolled magnesium (Mg) alloy have been investigated using real-time in situ neutron diffraction under a continuous-loading condition. It is found that by introducing the excess twinned grains through pre-compression along the rolling direction the fatigue life was enhanced approximately 50%, mainly resulting from the prolonged detwinning process and inhibited dislocation slip during reverse tension. Moreover, after pre-twinning process, the removal of the rapid strain hardening during reverse tension leads to a compressive mean stress value and more symmetric shape of stress-strain hysteresis loop. The pre-twinning has significant impacts on the twinning-detwinning characteristics and deformation modes during cyclic loading and greatly facilitates the twinning-detwinning activities in plastic deformation. The cyclic straining leads to the increase of contribution of tensile twinning deformation in overall plastic deformation in both the as-received and pre-deformed sample. The mechanisms of load partitioning in different groups of grains are closely related to the deformation modes in each deformation stage, while the fatigue cycling has little influence on the load sharing. The pre-twinning process provides an easy and cost-effective route to improve the low-cycle fatigue life through manufacturing and processing, which would advance the wide application of light-weight wrought Mg alloys as structural materials.

36 MATERIALS SCIENCE↗
DOE OSTI2015

A study of suppressed formation of low-conductivity phases in doped Li 7 La 3 Zr 2 O 12 garnets by in situ neutron diffraction

Doped Li 7 La 3 Zr 2 O 12 garnets, oxide-based solids with good Li + conductivity and compatibility, show great potential as leading electrolyte material candidates for all-solid-state lithium ion batteries. Still yet, the conductive bulk usually suffers from the presence of secondary phases and the transition towards a low-conductivity tetragonal phase during synthesis. Dopants are designed to stabilize the high-conductive cubic phase and suppress the formation of the low-conductivity phases. In situ neutron diffraction enables a direct observation of the doping effects by monitoring the phase evolutions during garnet synthesis. It reveals the reaction mechanism involving the temporary presence of intermediate phases. The off-stoichiometry due to the liquid Li 2 CO 3 evaporation leads to the residual of the low-conductivity intermediate phase in the as-synthesized bulk. Appropriate doping of an active element may alter the component of the intermediate phases and promote the completion of the reaction. While the dopants aid to stabilize most of the cubic phase, a small amount of tetragonal phase tends to form under a diffusion process. Lastly, the in situ observations provide the guideline of process optimization to suppress the formation of unwanted low-conductivity phases.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Understanding the role of NH 4 F and Al 2 O 3 surface co-modification on lithium-excess layered oxide Li 1.2 Ni 0.2 Mn 0.6 O 2

In this work we prepared Li 1.2 Ni 0.2 Mn 0.6 O 2 (LNMO) using a hydroxide co-precipitation method and investigated the effect of co-modification with NH 4 F and Al 2 O 3 . After surface co-modification, the first cycle Coulombic efficiency of Li 1.2 Ni 0.2 Mn 0.6 O 2 improved from 82.7% to 87.5%, and the reversible discharge capacity improved from 253 to 287 mAh g –1 at C/20. Moreover, the rate capability also increased significantly. A combination of neutron diffraction (ND), high-resolution transmission electron microscopy (HRTEM), aberration-corrected scanning transmission electron microscopy (a-STEM)/electron energy loss spectroscopy (EELS), and X-ray photoelectron spectroscopy (XPS) revealed the changes of surface structure and chemistry after NH 4 F and Al 2 O 3 surface co-modification while the bulk properties showed relatively no changes. These complex changes on the material s surface include the formation of an amorphous Al 2 O 3 coating, the transformation of layered material to a spinel-like phase on the surface, the formation of nanoislands of active material, and the partial chemical reduction of surface Mn 4+ . Such enhanced discharge capacity of the modified material can be primarily assigned to three aspects: decreased irreversible oxygen loss, the activation of cathode material facilitated with preactivated Mn 3+ on the surface, and stabilization of the Ni-redox pair. In conclusion, these insights will provide guidance for the surface modification in high-voltage-cathode battery materials of the future.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Origin of high Li⁺ conduction in doped Li₇La₃Zr₂O₁₂ garnets

Substitution of a native ion in the crystals with a foreign ion that differs in valence ( aliovalent doping ) has been widely attempted to upgrade solid-state ionic conductors for various charge carriers including O²⁻, H⁺, Li⁺, Na⁺, etc. The doping helps promote the high-conductive framework and dredge the tunnel for fast ion transport. The garnet-type Li₇La₃Zr₂O₁₂ (LLZO) is a fast Li⁺ solid conductor, which received much attention as an electrolyte candidate for all-solid-state lithium ion batteries, showing great potential to offer high energy density and minimize battery safety concerns to meet extensive applications in large energy storage systems such as those for electric vehicles and aerospace. In the Li-stuffed garnet framework of LLZO, the 3D pathway formed by the incompletely occupied tetrahedral sites bridged by a single octahedron enables the superior Li⁺ conductivity. For optimal performance, many aliovalent-doping efforts have been made throughout metal elements (Al³⁺, Ta⁵⁺) and metalloid elements (Ga³⁺, Te⁶⁺) in the periodic table with various valences to stabilize the high-conductive phase and increase the Li vacancy concentration.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Correlation of anisotropy and directional conduction in β-Li{sub 3}PS{sub 4} fast Li{sup +} conductor

This letter reports the correlation of anisotropy and directional conduction in the fast Li{sup +} conductor β-Li{sub 3}PS{sub 4}, one of the low-symmetry crystalline electrolyte candidates. The material has both high conductivity and good stability that serves well for the large-scale energy storage applications of all-solid-state lithium ion batteries. The anisotropic physical properties, demonstrated here by the thermal expansion coefficients, are crucial for compatibility in the solid-state system and battery performance. Neutron and X-ray powder diffraction measurements were done to determine the crystal structure and thermal stability. The crystallographic b-axis was revealed as a fast expansion direction, while negligible thermal expansion was observed along the a-axis around the battery operating temperatures. The anisotropic behavior has its structural origin from the Li{sup +} conduction channels with incomplete Li occupancy and a flexible connection of LiS{sub 4} and PS{sub 4} tetrahedra within the framework. This indicates a strong correlation in the direction of the ionic transport in the low-symmetry Li{sup +} conductor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

The migration mechanism of transition metal ions in LiNi 0.5 Mn 1.5 O 4

The migration of transition metal ions in the oxygen framework was recently proposed to be responsible for the continuous loss of average working potential of high energy density layered–layered composite cathodes for lithium-ion batteries. The potential migration pathway in a model material, LiNi 0.5 Mn 1.5 O 4 spinel, was investigated using in situ high-energy X-ray diffraction and in situ neutron diffraction during the solid state synthesis process. It was found that the migration of transition metal ions among octahedral sites is possible by using tetrahedral vacancies as intermediate sites. It was also suggested that the number of electrons in 3d orbitals has a significant impact on their mobility in the hosting oxygen framework.

25 ENERGY STORAGE↗
DOE OSTI2015

Deformation mechanisms in a precipitation-strengthened ferritic super alloy revealed by in situ neutron dffraction studies at elevated temperatures

The ferritic superalloy Fe–10Ni–6.5Al–10Cr–3.4Mo strengthened by ordered (Ni,Fe)AlB2-type precipitates is a candidate material for ultra-supercritical steam turbine applications above 923 K. Despite earlier success in improving its room-temperature ductility, the creep resistance of this material at high temperatures needs to be further improved, which requires a fundamental understanding of the high-temperature deformation mechanisms at the scales of individual phases and grains. In situ neutron diffraction has been utilized to investigate the lattice strain evolution and the microscopic load-sharing mechanisms during tensile deformation of this ferritic superalloy at elevated temperatures. Finite-element simulations based on the crystal plasticity theory are employed and compared with the experimental results, both qualitatively and quantitatively. Based on these interphase and intergranular load-partitioning studies, it is found that the deformation mechanisms change from dislocation slip to those related to dislocation climb, diffusional flow and possibly grain boundary sliding, below and above 873 K, respectively. Insights into microstructural design for enhancing creep resistance are also discussed.

nuclear (including radiation effects), defects, me↗
DOE OSTI2014

Unraveling cyclic deformation mechanisms of a rolled magnesium alloy using in situ neutron diffraction

In the current study, the deformation mechanisms of a rolled magnesium alloy were investigated under cyclic loading using real-time in situ neutron diffraction under a continuous-loading condition. The relationship between the macroscopic cyclic deformation behavior and the microscopic response at the grain level was established. The neutron diffraction results indicate that more and more grains are involved in the twinning and detwinning deformation process with the increase of fatigue cycles. The residual twins appear in the early fatigue life, which is responsible for the cyclic hardening behavior. The asymmetric shape of the hysteresis loop is attributed to the early exhaustion of the detwinning process during compression, which leads to the activation of dislocation slips and rapid strain-hardening. The critical resolved shear stress for the activation of tensile twinning closely depends on the residual strain developed during cyclic loading. In the cycle before the sample fractured, the dislocation slips became active in tension, although the sample was not fully twinned. The increased dislocation density leads to the rise of the stress concentration at weak spots, which is believed to be the main reason for the fatigue failure. Furthermore, the deformation history greatly influences the deformation mechanisms of hexagonal-close-packed-structured magnesium alloy during cyclic loading.

36 MATERIALS SCIENCE↗
DOE OSTI2014

A high-temperature neutron diffraction study of Nb 2 AlC and TiNbAlC

In this paper, we report on the crystal structures of Nb 2 AlC and TiNbAlC actual composition (Ti 0.45 ,Nb 0.55 ) 2 AlC compounds determined from Rietveld analysis of neutron diffraction patterns in the 300-1173 K temperature range. The average linear thermal expansion coefficients of a Nb 2 AlC sample in the a and c directions are, respectively, 7.9(5)x10 -6 K -1 and 7.7(5)x10 -6 K -1 on one neutron diffractometer and 7.3(3)x10 -6 K -1 and 7.0(2)x10 -6 K -1 on a second diffractometer. The respective values for the (Ti 0.45 ,Nb 0.55 ) 2 AlC composition - only tested on one diffractometer - are 8.5(3)x10 -6 K -1 and 7.5(5)x10 -6 K -1 . These values are relatively low compared to other MAX phases. Like other MAX phases, however, the atomic displacement parameters show that the Al atoms vibrate with higher amplitudes than the Ti and C atoms, and 1 more along the basal planes than normal to them. In addition, when the predictions of the atomic displacement parameters obtained from density functional theory are compared to the experimental results, good quantitative agreement is found for the Al atoms. In case of the Nb and C atoms, the agreement was more qualitative.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Extracting grain-orientation-dependent data from in situ time-of-flight neutron diffraction. I. Inverse pole figures

The problem of calculating the inverse pole figure (IPF) is analyzed from the perspective of the application of time-of flight neutron diffraction to in situ monitoring of the thermomechanical behavior of engineering materials. On the basis of a quasi-Monte Carlo (QMC) method, a consistent set of grain orientations is generated and used to compute the weighting factors for IPF normalization. The weighting factors are instrument dependent and were calculated for the engineering materials diffractometer VULCAN (Spallation Neutron Source, Oak Ridge National Laboratory). The QMC method is applied to face-centered cubic structures and can be easily extended to other crystallographic symmetries. Examples include 316LN stainless steel in situ loaded in tension at room temperature and an Al–2%Mg alloy, substantially deformed by cold rolling and in situ annealed up to 653 K.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2014

In-situ neutron diffraction of LaCoO₃ perovskite under uniaxial compression. I. Crystal structure analysis and texture development

The dynamics of texture formation, changes in crystal structure, and stress accommodation mechanisms have been studied in perovskite-type R3⁻c rhombohedral LaCoO₃ during uniaxial compression using in-situ neutron diffraction. The in-situ neutron diffraction revealed the complex crystallographic changes causing the texture formation and significant straining along certain crystallographic directions during compression, which are responsible for the appearance of hysteresis and non-linear ferroelastic deformation in the LaCoO₃ perovskite. The irreversible strain after the first loading was connected with the appearance of non-recoverable changes in the intensity ratio of certain crystallographic peaks, causing non-reversible texture formation. However, in the second loading/unloading cycle, the hysteresis loop was closed and no further irrecoverable strain appeared after deformation. The significant texture formation is responsible for an increase in the Young's modulus of LaCoO₃ at high compressive stresses, ranging from 76 GPa at the very beginning of the loading to 194 GPa at 900 MPa at the beginning of the unloading curve.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

In-situ neutron diffraction of LaCoO{sub 3} perovskite under uniaxial compression. II. Elastic properties

Calculations of elastic constants and development of elastic anisotropy under uniaxial compression in originally isotropic polycrystalline LaCoO{sub 3} perovskite are reported. The lattice strains in individual (hkl) planes as well as average lattice strain were determined both for planes oriented perpendicular and parallel to the loading direction using in-situ neutron diffraction. Utilizing average lattice strains as well as lattice strains along the a and c crystallographic directions, an attempt was made to determine Poisson's ratio of LaCoO{sub 3}, which was then compared with that measured using an impulse excitation technique. The elastic constants were calculated and Young's moduli of LaCoO{sub 3} single crystal in different crystallographic directions were estimated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗