Engineering Papers⌕ Search

Engineering topics

Amonette, James E

Publications and source records attributed to Amonette, James E.

At least 19 records

Geochemical Implications of Gas Leakage Associated with Geologic CO2 Storage - A Qualitative Review

Leakage from deep storage reservoirs is considered the major risk factor associated with geologic sequestration of CO2. Different schools of thought exist concerning the potential implications of such leakage for near-surface environments. We reviewed the current literature on how CO2 leakage (from storage reservoirs) would likely impact the geochemistry of overlying potable aquifers. Results from experimental and modeling studies point to the potential for both beneficial (e.g. contaminant immobilization) and deleterious (e.g. contaminant mobilization) consequences of CO2 intrusion into potable groundwater. However, there are significant discrepancies between studies particularly concerning, what contaminants are of concern and the geochemical processes involved. These discrepancies reflected the lack of a consensus on CO2-induced changes in subsurface geochemical processes and subsequent effects on groundwater chemistry. The development of consistent experimental protocols and the identification of pertinent factors driving CO2-induced geochemical changes in the subsurface were identified as key research needs. Geochemical modeling was used to systematically highlight why a standardization of experimental protocols and the consideration of experimental factors such as gas leakage rates, redox status and the influence of co-transported gases are pertinent. The role of analog studies, reactions occurring in the vadose zone, and the influence of organic contaminants are also discussed.

basalts↗

An electron paramagnetic resonance spectroscopy investigation of the retention mechanisms of Mn and Cu in the nanopore channels of three zeolite minerals

The adsorption mechanisms of divalent cations in zeolite nanopore channels can vary as a function of their pore dimensions. The nanopore inner-sphere enhancement (NISE) theory predicts that ions may dehydrate inside small nanopore channels in order to adsorb more closely to the mineral surface if the nanopore channel is sufficiently small. The results of an electron paramagnetic resonance (EPR) spectroscopy study of Mn and Cu adsorption on the zeolite minerals zeolite Y (large nanopores), ZSM-5 (intermediate nanopores), and mordenite (small nanopores) are presented. The Cu and Mn cations both adsorbed via an outer-sphere mechanism on zeolite Y based on the similarity between the adsorbed spectra and the aqueous spectra. Conversely, Mn and Cu adsorbed via an inner-sphere mechanism on mordenite based on spectrum asymmetry and peak broadening of the adsorbed spectra. However, Mn adsorbed via an outer-sphere mechanism on ZSM-5, whereas Cu adsorbed on ZSM-5 shows a high degree of surface interaction that indicates that it is adsorbed closer to the mineral surface. Evidence of dehydration and immobility was more readily evident in the spectrum of mordenite than ZSM-5, indicating that Cu was not as close to the surface on ZSM-5 as it was when adsorbed on mordenite. Divalent Mn cations are strongly hydrated and are held strongly only in zeolites with small nanopore channels. Divalent Cu cations are also strongly hydrated, but can dehydrate more easily, presumably due to the Jahn-Teller effect, and are held strongly in zeolites with medium sized nanopore channels or smaller.

copper↗

Influence of Aging and Environment on Nanoparticle Chemistry: Implication to Confinement Effects in Nanoceria

The oxidation state switching of cerium in cerium oxide nanoparticles is studied in detail. The influence of synthesis medium, aging time and local environment on the oxidation state switching, between +3 and + 4, is analyzed by tracking the absorption edge using UV-Visible spectroscopy. It is observed that by tuning the local environment, the chemistry of the nanoparticles could be altered. These time dependent, environmentally induced changes likely contribute to inconsistencies in the literature regarding quantum-confinement effects for ceria nanoparticles. The results in this article indicate that there is a need to carry out comprehensive analysis of nanoparticles while considering the influence of synthesis and processing conditions, aging time and local environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Biochars impact on soil moisture storage in an Ultisol and two Aridisols

Biochar additions to soils can improve soil water storage capability, however, there is sparse information identifying feedstocks and pyrolysis conditions that maximize this improvement. Nine biochars were pyrolyzed from five feedstocks at two temperatures and their physical and chemical properties were characterized. Biochars were mixed at 2% wt w{sup -1} into a Norfolk loamy sand (Fine-loamy, kaolinitic, thermic Typic Kandiudult), a Declo silt loam (Coarse-loamy, mixed, superactive, mesic xeric Haplocalcid), or a Warden silt loam (Coarse-silty, mixed, superactive, mesic xeric Haplocambid). Untreated soils served as controls. Soils were laboratory incubated in pots for 127 days and were leached about every 30 days with deionized water. Soil bulk densities were measured before each leaching event. For six days thereafter, pot holding capacities (PHC) for water were determined gravimetrically and were used as a surrogate for soil moisture contents. Water tension curves were also measured on the biochar treated and untreated Norfolk soil. Biochar surface area, surface tension, ash, C, and Si contents, in general, increased when produced under higher pyrolytic temperatures ({ge}500 C). Both switchgrass biochars caused the most significant water PHC improvements in the Norfolk, Declo and Warden soils compared to the controls. Norfolk soil water tension results at 5 and 60 kPa corroborated that biochar from switchgrass caused the most significant moisture storage improvements. Significant correlation occurred between the PHC for water with soil bulk densities. In general, biochar amendments enhanced the moisture storage capacity of Ultisols and Aridisols, but the effect varied with feedstock selection and pyrolysis temperature.

54 ENVIRONMENTAL SCIENCES↗

THE EFFECT OF SMECTITE ON THE CORROSION OF IRON METAL

The combination of zero-valent iron and a clay-type amendment is often observed to have a synergistic effect on the rate of reduction reactions. In this paper, electrochemical techniques are used to determine the mechanism of interaction between the iron and smectite clay minerals. Iron electrodes coated with an evaporated smectite suspension (clay-modified iron electrodes, CMIEs) were prepared using five different smectites: SAz-1, SWa-1, STx-1, SWy-1, and SHCa-1. All the smectites were exchanged with Na+ and one sample of SWy-1 was also exchanged with Mg2+. Potentiodynamic potential scans and cyclic voltammograms were taken using the CMIEs and uncoated but passivated iron electrodes. These electrochemical experiments, along with measurements of the amount of Fe2+ and Fe3+ sorbed in the smectite coating, suggested that the smectite removed the passive layer of the underlying iron electrode during the evaporation process. Cyclic voltammograms taken after the CMIEs were biased at the active-passive transition potential for varying amounts of time suggested that the smectite limited growth of a passive layer, preventing passivation. These results are attributed to the Broensted acidity of the smectite as well as to its ability to sorb iron cations. Oxides that did form on the surface of the iron in the presence of the smectite when it was biased anodically seemed to be different than those that form on the surface of an uncoated iron electrode under otherwise similar conditions; this difference suggested that the smectite reacted with the Fe2+ formed from the oxidation of the underlying iron. No significant correlation could be found between the ability of the smectite to remove the iron passive film and the smectite type. The results have implications for the mixing of sediments and iron particles in permeable reactive barriers, underground storage of radioactive waste in steel canisters, and the use of smectite supports in preventing aggregation of nano-sized zero-valent iron.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Recovery of Iron/Iron Oxide Nanoparticles from Solution: Comparison of Methods and their Effects

Most methods currently being used to recover Fe0-core/oxide-shell nanoparticles from solutions (including the solvents they are synthesized or stored in) are potentially problematic because they may alter the particle composition (e.g., depositing salts formed from solutes) or leave the particles prone to transformations during subsequent storage and handling (e.g., due to residual moisture). In this study, several methods for recovery of nanoparticles from aqueous solution were studied to determine how they affect the structure and reactivity of the recovered materials. Simple washing of the nanoparticles during vacuum filtration (i.e., “flash drying”) can leave up to ~17 weight percent residual moisture. Modeling calculations suggest this moisture is mostly capillary or matric water held between particles and particle aggregates, which can be removed by drying for short periods at relative vapor pressures below 0.9. Flash drying followed by vacuum drying, all under N2, leaves no detectable residue from precipitation of solutes (detectable by X-ray photoelectron spectroscopy, XPS), no significant changes in overall particle composition or structure (determined by transmission electron microscopy, TEM), and negligible residual moisture (by thermogravimetric analysis, TGA). While this improved flash-drying protocol may be the preferred method for recovering nanoparticles for many purposes, we found that Fe0-core/oxide-shell nanoparticles still exhibit gradual aging during storage when characterized electrochemically with voltammetry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Accelerated Cellulose Depolymerization Catalyzed by Paired Metal Chlorides in Ionic Liquid Solvent

Efficient hydrolytic depolymerization of crystalline cellulose to sugars is a critical step and has been a major barrier for improved economics in the utilization of cellulosic biomass. We report a novel catalytic system involving paired metal chlorides in an ionic liquid that considerably accelerates the rate of cellulose depolymerization under mild conditions. Paired metal chlorides, consisting of CuCl2 (primary metal chloride) and a second metal chloride, such as CrCl2, PdCl2, CrCl3 or FeCl3 in 1-ethyl-3-methylimidazolium chloride ([EMIM]Cl) solvent were found to substantially accelerate the hydrolytic cleavage of 1,4-glucosidic bonds as compared to known acid-catalyzed hydrolysis in similar temperature range (80-120°C). In contrast, single metal chlorides with the same total molar loading showed much lower activity under similar conditions. Experimental results illustrate the dramatic effect of the second metal chloride in the paired catalytic system. A combination of characterization techniques, including electron paramagnetic resonance (EPR) spectroscopy, differential scanning calorimetry (DSC), X-ray absorption fine structure (XAFS) spectroscopy, and X-ray absorption near edge structure (XANES) spectroscopy, were used to reveal a preliminary understanding of possible mechanisms involved in the paired CuCl2/PdCl2 catalytic system. Results suggest that the C2-proton of the imidazolium ring may be activated by the paired metal-chloride catalysts.

09 BIOMASS FUELS↗

Abiotic Degradation Rates for Carbon Tetrachloride and Chloroform: Progress in FY 2010

This report documents the progress made through FY 2010 on a project initiated in FY 2006 to help address uncertainties related to the rates of hydrolysis in groundwater at the Hanford Site for carbon tetrachloride (CT) and chloroform (CF). The study also explores the possible effects of contact with minerals and sediment (i.e., heterogeneous hydrolysis) on these rates. The research was initiated to decrease the uncertainties in abiotic degradation rates of CT and chloroform CF associated with temperature and possible heterogeneous effects. After 2 years of data collection, the first evidence for heterogeneous effects was identified for hydrolysis of CT, and preliminary evidence for the effects of different mineral types on CF hydrolysis rates also was reported. The CT data showed no difference among mineral types, whereas significant differences were seen in the CF results, perhaps due to the fact that CF hydrolyzes by both neutral and base-catalyzed mechanisms whereas CT follows only the neutral hydrolysis path. In this report, we review the project objectives, organization, and technical approaches taken, update the status and results of the hydrolysis-rate experiments after 4 years of experimentation (i.e., through FY 2010), and provide a brief discussion of how these results add to scientific understanding of the behavior of the CT/CF plume at the Hanford Site.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

An investigation into the reactions of biochar in soil

Interactions between biochar, soil, microbes and plant roots may occur within a short period of time after application to the soil. The extent, rates and implications of these interactions, however, are far from being understood. This review includes a description of the properties of biochars and suggests possible reactions that may occur after the addition of biochars to soil. These include dissolution-precipitation, adsorption-desorption, acid-base and redox reactions. Special attention is given to reactions occurring within pores, and to interactions with roots, microorganisms and soil fauna. The examination of biochars (from chicken litter, greenwaste and paper mill sludges) weathered for one and two years in an Australian Ferrosol provides evidence for some of the mechanisms described in this review and offers an insight to reactions at a molecular scale. These interactions are biochar- and site-specific. Therefore, suitable experimental trials combining biochar types and different pedoclimatic conditions are needed to determine the extent to which these reactions influence the potential of biochar as a soil amendment and C-sequestration tool.

54 ENVIRONMENTAL SCIENCES↗

[CuCln](2-n) Ion-Pair Species in 1-Ethyl-3-Methylimidazolium Chloride Ionic Liquid-Water Mixtures: Ultraviolet-Visible, X-ray Absorbtion Fine Structure, and Density Functional Theory Characterization

We report details of the coordination environment about Cu(II) in a pure ionic liquid, 1- ethyl-3-methylimidazolium chloride ([EMIM]Cl) and in mixtures containing varying amounts of water from 0-100% of the [EMIM]Cl. There are many stages in the ion pairing of the divalent cation, Cu(II) including the contact ion pairing of Cu2+ with multiple Cl- to form various CuCln (2-n) polyanions. Thereis also the subsequent solvation and ion pairing of the polychlorometallate anion with the EMIM+ cation. Using a combination of x-ray absorption fine structure (XAFS), UV-Vis spectroscopy and electronic structure calculations (TDDFT) we are able to follow the detailed structural changes about Cu(II). Ion pair formation is strongly promoted in [EMIM]Cl by the low dielectric constant and by the extensive breakdown of the water hydrogen bond network in [EMIM]Cl/water mixtures. In the [EMIM]Cl solvent the CuCl4 2- species dominates and it’s geometry is quite similar to gas-phase structure. These results are important in understanding catalysis and separation processes involving transition metals in ionic liquid systems.

08 HYDROGEN↗

Role of Biochar in Mitigation of Climate Change

By virtue of the large fraction of the terrestrial carbon (C) cycle controlled by human activities, agroecosystems are both sources and sinks for greenhouse gases. Their potential role in mitigation of climate change thus depends on a dual strategy of decreasing greenhouse gas emissions while increasing sinks so that the net impact on climate warming is less than at present. Emissions of carbon dioxide, methane and nitrous oxide arise from various agricultural activities, ranging from land clearing to ploughing, fertilization, and animal husbandry. Reductions in these emissions can be achieved by decreasing the heterotrophic conversion of organic C to carbon dioxide, and by better management of agricultural waste streams to minimize release of methane and nitrous oxide. Current sinks include C stored in standing biomass and soil organic matter, and the oxidation of atmospheric methane by soil bacteria. These sinks can be enhanced by increasing net primary productivity, thereby actively withdrawing more carbon dioxide from the atmosphere, and by promoting more oxidation of methane by soils. Judicious biochar management may contribute to both strategies, reductions of emissions by agriculture and active withdrawal of atmospheric carbon dioxide, as part of a comprehensive scheme in agricultural and forestry watersheds. Biochar is a carbon-rich organic material generated by heating biomass in the absence, or under a limited supply, of oxygen. This so-called charring or pyrolysis process has been used to produce charcoal as a source of fuel for millennia. Recently, interest has grown in understanding the potential of this process to improve soil health by adding biochar as an amendment to soil, to manage agricultural and forestry wastes, to generate energy, to decrease net emissions of nitrous oxide and methane, and to store carbon (C). The main incentive of biochar systems for mitigation of climate change is to increase the stability of organic matter or biomass. This stability is achieved by the conversion of fresh organic materials, which mineralize comparatively quickly, into biochar, which mineralizes much more slowly. The difference between the mineralization of uncharred and charred material results in a greater amount of carbon storage in soils and a lower amount of carbon dioxide, the major greenhouse gas, in the atmosphere. The principle of creating and managing biochar systems may address multiple environmental constraints. Biochar may help not only in mitigating climate change, but also fulfill a role in management of agricultural and forestry wastes, enhancement of soil sustainability, and generation of energy. Pyrolysis is a comparatively low-technology intervention. Deployment on a global scale, however, must be done carefully if the full mitigation potential is to be reached. Critical aspects of a successful implementation are that: 1) the biochar is sufficiently stable to reduce greenhouse gases in the atmosphere for an appropriate length of time. 2) the storage of carbon as biochar in soil is not offset by greenhouse gas emissions along the value chain of the system, such as mineralization of soil carbon or emissions of other greenhouse gases (e.g., methane and nitrous oxide). 3) net emission reductions are achieved for the entire life cycle of the system including indirect land use. 4) the biochar product does not cause unwanted side effects in soil. 5) the handling and production of biochar are in compliance with health and safety standards and do not pose hurdles to implementation. and 6) the biochar system is financially viable. This chapter discusses these issues in separate sections, identifies knowledge gaps, and proposes a road map to fully evaluate an environmentally and socially safe exploration of the biochar potential to mitigate climate change if adopted widely around the world.

03 NATURAL GAS↗

Sustainable biochar to mitigate global climate change

Production of biochar (the carbon-rich solid formed by pyrolysis of biomass), in combination with its storage in soils, has been suggested as a means to abate anthropogenic climate change, while simultaneously increasing crop yields. The climate mitigation potential stems primarily from the highly recalcitrant nature of biochar, which slows the rate at which photosynthetically fixed carbon is returned to the atmosphere. Significant uncertainties exist, however, regarding the impact, capacity, and sustainability of biochar for carbon capture and storage when scaled to the global level. Previous estimates, based on simple assumptions, vary widely. Here we show that, subject to strict environmental and modest economic constraints on biomass procurement and biochar production methods, annual net emissions of CO2, CH4 and N2O could be reduced by 1.1 - 1.9 Pg CO2-C equivalent (CO2-Ce)/yr (7 - 13% of current anthropogenic CO2-Ce emissions; 1Pg = 1 Gt). Over one century, cumulative net emissions of these gases could be reduced by 72-140 Pg CO2-Ce. The lower end of this range uses currently untapped residues and wastes; the upper end requires substantial alteration to global biomass management, but would not endanger food security, habitat or soil conservation. Half the avoided emissions are due to the net C sequestered as biochar, one-quarter to replacement of fossil-fuel energy by pyrolysis energy, and one-quarter to avoided emissions of CH4 and N2O. The total mitigation potential is 18-30% greater than if the same biomass were combusted to produce energy. Despite limited data for the decomposition rate of biochar in soils and the effects of biochar additions on soil greenhouse-gas fluxes, sensitivity within realistic ranges of these parameters is small, resulting in an uncertainty of ±8% (±1 s.d.) in our estimates. Achieving these mitigation results requires, however, that biochar production be performed using only low-emissions technologies and feedstocks obtained sustainably, with minimal carbon debt incurred from land-use change.

54 ENVIRONMENTAL SCIENCES↗

Characterization and Reactivity of Iron Nanoparticles Prepared with Added Cu, Pd, and Ni

The presence of a secondary metal on iron particles affects redox reactivity in engineered remediation systems. However, the structural characteristics of the metal additives and mechanism responsible for changes in reactivity have not been fully elucidated. Here, we synthesized iron nanoparticles with Cu, Pd, and Ni content ranging from 0-2 mol% via a solution deposition process (SDP), hydrogen reduction process (HRP), or hydrogen reduction of ferrihydrite coprecipitated with the metal cations (HRCO). Results from solid-state characterization show that the synthetic methods produced similar iron core/magnetite shell particles but produced substantial differences in terms of the distribution of the metal additive. In SDP, the metal additives were heterogeneous distributed on the surface of the particles. The metal additives were clearly discernable in TEM images as spherical nanoparticles (2-4 nm) on the HRP and HRCO particles. In addition, we hypothesize that the metal additive is also present as solute within the iron core of the HRCO particles. Kinetic batch experiments of carbon tetrachloride (CT) degradation were performed to quantitatively compare the redox reactivity of the particles. Overall, metal additives resulted in enhanced overall pseudo-first order rate constants of CT degradation (kO,CT) compared to that of the iron nanoparticles. For the bimetallic iron nanoparticles prepared by SDP and HRP, kO,CT increased with the concentration of metal additives. The values of chloroform yield (YCF) were independent of the identity and amount of metal additives. However, both kO,CT and YCF of the HRCO iron particles were significantly greater. Results suggest that it is the distribution of the metal additives that most strongly impacts reactivity and product distribution. For example, for materials with ca. 0.9 50 mol% Ni, reactivity and YCF varied substantially (HRCO>SDP>HRP), and HRCO-NiFe resulted in the lowest final chloroform concentration because the chloroform was rapidly dechlorinated. In addition, sequential spike experiments for long-term reactivity demonstrated that the presence of the metal additives facilitated reduction by enabling greater utilization of Fe0.

54 ENVIRONMENTAL SCIENCES↗

Abiotic Degradation Rates for Carbon Tetrachloride and Chloroform: Progress in FY2009

This report documents the progress made through FY 2009 on a project initiated in FY 2006 to help address uncertainties related to the rates of hydrolysis in groundwater for carbon tetrachloride (CT) and chloroform (CF). The study seeks also to explore the possible effects of contact with minerals and sediment (i.e., heterogeneous hydrolysis) on these rates. In previous years the work was funded as two separate projects by various sponsors, all of whom received their funding from the U.S. Department of Energy (DOE). In FY2009, the projects were combined and funded by CH2MHill Plateau Remediation Corporation (CHPRC). Work in FY2009 was performed by staff at the Pacific Northwest National Laboratory (PNNL). Staff from the State University of New York at Cortland (SUNY–Cortland) contributed in previous years.

54 ENVIRONMENTAL SCIENCES↗

A shallow subsurface controlled release facility in Bozeman, Montana, USA, for testing near surface CO2 detection techniques and transport models

A facility has been constructed to perform controlled shallow releases of CO2 at flow rates that challenge near surface detection techniques and can be scalable to desired retention rates of large scale CO2 storage projects. Preinjection measurements were made to determine background conditions and characterize natural variability at the site. Modeling of CO2 transport and concentration in saturated soil and the vadose zone was also performed to inform decisions about CO2 release rates and sampling strategies. Four releases of CO2 were carried out over the summer field seasons of 2007 and 2008. Transport of CO2 through soil, water, plants, and air was studied using near surface detection techniques. Soil CO2 flux, soil gas concentration, total carbon in soil, water chemistry, plant health, net CO2 flux, atmospheric CO2 concentration, movement of tracers, and stable isotope ratios were among the quantities measured. Even at relatively low fluxes, most techniques were able to detect elevated levels of CO2 in the soil, atmosphere, or water. Plant stress induced by CO2 was detectable above natural seasonal variations.

54 ENVIRONMENTAL SCIENCES↗

Intra-annual changes in biomass, carbon, and nitrogen dynamics at 4-year old switchgrass field trials in West Tennessee, USA

Switchgrass is a potential bioenergy crop that could promote soil C sequestration in some environments. We compared four cultivars on a well-drained Alfisol to test for differences in biomass, C, and N dynamics during the fourth growing season. There was no difference (P > 0.05) among cultivars and no significant cultivar x time interaction in analyses of dry mass, C stocks, or N stocks in aboveground biomass and surface litter. At the end of the growing season, mean (±SE) aboveground biomass was 2.1±0.13 kg m-2, and surface litter dry mass was approximately 50% of aboveground biomass. Prior to harvest, the live root:shoot biomass ratio was 0.76. There was no difference (P > 0.05) among cultivars for total biomass, C, and N stocks belowground. Total belowground biomass (90-cm soil depth) as well as coarse (greater than or equal to 1 mm diameter) and fine (< 1 mm diameter) live root biomass increased from April to October. Dead roots were less than 7% of live root biomass to a depth of 90 cm. Net production of total belowground biomass (505 ±132 g m-2) occurred in the last half of the growing season. The increase in total live belowground biomass (426 ±139 g m-2) was more or less evenly divided among rhizomes, coarse, and fine roots. The N budget for annual switchgrass production was closely balanced with 6.3 g N m-2 removed by harvest of aboveground biomass and 6.7 g N m-2 supplied by fertilization. At the location of our study in west Tennessee, intra-annual changes in biomass, C, and N stocks belowground were of greater importance to crop management for C sequestration than were differences among cultivars.

09 BIOMASS FUELS↗

Spatio-temporal changes in CO2 emissions during the second ZERT injection, August-September 2008

This study reports the first field test of a multi-channel, auto-dilution, steady-state, soil-CO2 flux monitoring system being developed to help understand the pathways by which fugitive CO2 from a geologic sequestration site migrates to the surface. The test was conducted from late August through mid-October 2008 at the Zero Emissions Research and Technology (ZERT) project site located in Bozeman, MT. Twenty steady-state and five non-steady-state flux chambers were installed in a 10x15 m area, one boundary of which was directly above a shallow (2-m depth) horizontal injection well located 0.5 m below the water table. A total flux of 52 kg CO2 d-1.was injected into the well for 13 days and the efflux from the soil was monitored by the chambers before, during, and for 33 days after the injection. The results showed a rapid increase in soil efflux once injection started, with maximal values reached within 3-7 d in most chambers. Efflux returned to background levels within a similar time period after injection ceased. A radial efflux pattern was observed to at least 2 m from the injection well, and evidence for movement of the CO2 plume during the injection, presumably due to groundwater flow, was seen. The steady-state chambers yielded very stable data, but 3- to 5-fold higher fluxes than the non-steady-state chambers. The higher fluxes were attributed to vacuum induced in the steady-state chambers by narrow vent tubes. High winds resulted in significant decreases in measured soil CO2 efflux, presumably by enhancing efflux from soil outside the chambers.

continuous monitoring↗

Terrestrial Biological Carbon Sequestration: Science for Enhancement and Implementation

Fossil-fuel combustion and land-use change have elevated atmospheric CO2 concentrations from 280 ppmv at the beginning of the industrial era to more than 381 ppmv in 2006. Carbon dioxide emissions from fossil fuels and cement rose 71% during 1970–2000 to a rate of 7.0 PgC/y (1). Canadell et al. (2) estimated that CO2 emissions rose at a rate at 1.3% per year during 1990–1999, but since 2000 it has been growing at 3.3% per year. Emissions reached 8.4 PgC/y in 2006. It is likely that the current 2-ppm annual increase will accelerate as the global economy expands, increasing the risk of climate system impacts. There is good agreement that photosynthetic CO2 capture from the atmosphere and storage of the C in above- and belowground biomass and in soil organic and inorganic forms could be exploited for safe and affordable greenhouse gas (GHG) mitigation (3). Nevertheless, C sequestration in the terrestrial biosphere has been a source of contention before and since the drafting of the Kyoto Protocol in 1997. Concerns have been raised that C sequestration in the biosphere is not permanent, that it is difficult to measure and monitor, that there would be “carbon leakage” outside of the mitigation activity, and that any attention paid to environmental sequestration would be a distraction from the central issue of reducing GHG emissions from energy production and use. A decade after drafting the Kyoto Protocol, it is clear that international accord and success in reducing emissions from the energy system are not coming easily and concerns about climate change are growing. It is time to re-evaluate all available options that might not be permanent yet have the potential to buy time, bridging to a future when new energy system technologies and a transformed energy infrastructure can fully address the climate challenge. Terrestrial sequestration is one option large enough to make a contribution in the coming decades using proven land-management methods and with the possibility that new technologies could significantly enhance the opportunity. Here we review progress on key scientific, economic, and social issues; postulate the extent to which new technologies might significantly enhance terrestrial sequestration potential; and address remaining research needs.

Post, W M↗