Engineering topics

Almer, Jonathan D.

Publications and source records attributed to Almer, Jonathan D..

7 records

All sources NASA NTRS DOE OSTI

DOE OSTI2023

High-Energy X-ray Diffraction Microscopy for Nuclear Forensics (FY23 Project Report)

36 MATERIALS SCIENCE↗

DOE OSTI2023

Correlations of multiscale structural evolution and homogeneous flows in metallic glass ribbons

Studying the flow behavior is critical to understand the deformation mechanism of amorphous solids. However, detecting the basic flow events in amorphous solids is challenging. Here, by simultaneous SAXS/WAXS, elementary flow carriers in wound metallic glasses are identified from flow-induced structural heterogeneities with a radius of gyration of 2.5~3.5 nm. Their size increases and morphology changes from sphere-like to rod-like under flow. Moreover, the atomic structure exhibits an unusual change to a more disordered state during winding/annealing at the temperature of ~0.8 T g . This work provides an atomic-to-nanoscale description of the flow carriers of amorphous solids during deformation. Impact Statement The elementary flow carriers in metallic glasses have a radius of gyration of 2.5~3.5 nm. During flow, their size increases and morphology changes from sphere-like to rod-like.

36 MATERIALS SCIENCE↗

DOE OSTI2022

High-Energy X-ray Diffraction Microscopy for Nuclear Forensics FY2022 Project Report

Morphological information on nuclear material has been identified using visible light and scanning electron microscopy. These identify qualitative differences in particle morphology. Three-dimensional imaging of materials through alternating scanning electron microscopy imaging and focused ion beam milling has also been used. Unfortunately, these techniques are time- and labor-intensive, with significant sample preparation required and lengthy analysis times. Further, the resulting 3D images are qualitative, require manual identification, and do not capture statistically-representative populations. High energy X-ray 3D imaging using a direct-beam or diffracted-beam (High-Energy Diffraction Microscopy) have been developed at the Advanced Photon Source and can produce quantitative information on grains (phase, location, etc.) and pores (size distribution, sphericity) in a material. These techniques require only minutes to characterize a sample volume and are non-destructive, thus suitable for a wide range of existing samples and for confirmatory analyses to be carried out using conventional microscopy techniques. In this first year of the project, all uranium oxide samples were synthesized and characterized using conventional analyses by the analytical chemistry laboratory. Conventional analysis methods included powder x-ray diffraction, scanning electron microscopy, impurity analysis via inductively coupled plasma mass spectrometry, and infrared spectroscopy. Impurity analysis shows a drop in boron content from UO 3 to the lowest U 3 O 8 calcination temperature, but otherwise no appreciable difference in any sample. Analysis of diffraction data shows a flip of peaks from UO 3 dominated for the 600 °C calcined sample to U 3 O 8 dominated at 700 °C and 800 °C. Analysis of scanning electron microscopy images shows that with increased calcination temperature the size distribution of particles seems to increase and broaden. Both of these last findings are in line with previously published data, though this work used significantly fewer particles to simply show similar trends instead of getting truly quantitative particle analysis. Infrared analysis similarly shows ingrowth of U 3 O 8 as calcination temperature is increased, along with depression of peaks associated with UO 3 and water. Samples were prepared for analysis at the Advanced Photon Source at beamline 1-ID. It is anticipated that analysis will occur in November of 2022. AI/ML techniques to de-noise data coming out of 1-ID during the analyses was also developed during this time using previously gathered data. Preliminary results using a self-supervision technique called Noise2Selfshow good de-noising of data. Once the uranium oxide samples are analyzed, real data will be used to test the de-noising and other AI/ML techniques that may be developed in the second year of the project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

NNSA Advanced Photon Source Sector Opportunities Workshop (Workshop Summary)

An NNSA-Argonne National Laboratory workshop to define NNSA and external partner mission needs and opportunities at the Advanced Photon Source was held February 15-17, 2022. This workshop summary provides a fresh look at NNSA’s evolving mission needs, partner agency and university interests, x-ray photon characteristics, and technical requirements to meet those needs. The workshop was organized according to four breakout groups: Coupling dynamic drivers to a synchrotron, High explosives and chemical sciences, Process-structure-performance: X-ray experiments to understand materials behaviors, and Process-structure-performance: manufacturing and aging. This summary report describes the workshop outcomes, and the preliminary conceptual design for a dedicated Defense Materials Science Sector (DMSS) at the Advanced Photon Source.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Unveiling the origins of work-hardening enhancement and mechanical instability in laser shock peened titanium

Laser shock-peening (LSP) produces complex gradients in microstructures and residual stresses, which enables fabrication of metallic engineering components with superior mechanical properties. In this work, we use non-destructive and spatially resolved high-energy X-ray diffraction (HE-XRD) to investigate the influences of LSP on microstructure, surface topography, and residual stress for high purity titanium plates. LSP is found to produce large compressive in-plane residual stresses near the peened surface which monotonically decay to zero about 2.5 mm below the surface. These properties were also tracked during in-situ tensile loading, allowing stress partitioning and work-hardening rates to be measured as a function of depth. The surface region is found to have the highest work-hardening rate and remain mechanically stable up to sample failure. In addition, a crystal rigid rotation along a transversal axis of about 27 & nbsp; was observed at large applied strain near the surface region, which is attributed to the formation of denser dispersed shear bands. Furthermore, a sudden drop in tensile stress was observed at a depth of similar to 160 mu m from the LSP surface, indicating the formation of a localized mechanical instability zone (LMIZ). The origin of this LMIZ could be attributed to the increase in shear stress induced by a load transfer from LSP surface due to the formation of denser dispersed shear bands. These observations indicate a localized transition in deformation behavior has occurred from dispersed shear banding to LMIZ and homogeneous deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Intact archeological human bones and age at death studied with transmission x–ray diffraction and small angle x–ray scattering

In this work, high-energy, wide-angle x-ray scattering (WAXS, x-ray diffraction) and small-angle x-ray scattering (SAXS) were used to study intact human second metacarpal bones (mc2) from two UK archeological sites. A novel method correcting for irregular mass distribution was applied in these transmission geometry experiments done at beamline 1-ID of the Advanced Photon Source. The authors asked whether there were age-at-death-related changes in carbonated apatite (cAp) lattice parameters and whether SAXS could detect collagen D-period peaks in the archeological mc2. For each of the two sites, Ancaster and Wharram Percy in England, six female mc2s were studied; for each site, two were from each of three age-at-death cohorts (young, 18-29 years; middle, 30-49 years; old >= 50 years) along with a modern control mc2. The Rietveld method was applied to the WAXS patterns to provide precise lattice parameter values. The cAp lattice parameters did not correlate with age-at-death estimated from dental wear. From WAXS and the 00.2 diffraction peak widths, four archeological mc2s possessed coherently scattering domain lengths (crystallite c-axis sizes) that matched that of the modern mc2; SAXS revealed the same four archeological mc2 had D-period peak intensities equivalent to that of the modern mc2. The other eight archeological mc2s had significantly larger crystallite sizes (than the modern mc2) and weak or absent D-period peaks, differences attributed to diagenetic changes. Based on these data, the authors suggest that WAXS 00.2 peak width and SAXS D-period peak intensity can be used with intact bones to select those likely to retain largely unaltered tissue nanostructure, which might be required for other analyses. Taken as a whole, the results suggest detecting age-related deterioration in nanostructural features may be difficult in bone showing significant bioerosion.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

Chemo–mechanical properties of carbon fiber reinforced geopolymer interphase

Geopolymers, as a potentially environmentally friendly alternative to Portland cement, are increasingly attracting attention in the construction industry. Various methods have been applied for customizing the properties of geopolymers and improving their commercial viability. One of the promising methods for refining the properties of geopolymers such as their toughness is the use of short fibers. The effectiveness of a high-strength short fiber in the geopolymer matrix is largely dependent on the interfacial bonding between the fiber and its surrounding matrix. While the importance of this interfacial chemistry is highlighted in the literature, the characteristics of this bonding structure have not been fully understood. In this paper, we aim to investigate the bonding mechanism between the carbon fiber and metakaolin-based geopolymer matrix. For the first time, the existence and nature of the chemical bonding at the interfacial region (interphase) between carbon fiber and geopolymer matrix has been revealed. X-ray pair distribution function computed tomography (PDF-CT), field emission-scanning electron microscopy imaging, and nanoindentation techniques are employed to discern the chemo-mechanical properties of the interphase. PDF-CT results show the emergence of a new atom-atom correlation at the interfacial region (around 1.82 angstrom). This correlation is a characteristic of interfacial bonding between the fiber and its surrounding matrix, where the existence of chemical linkages (potentially Al-V-O-C) between fibers and the matrix contributes to the adhesion between the two constituents making up the composite. Due to such chemical bonding, the nanomechanical properties of the interfacial region fall between that of the carbon fiber and geopolymer. The combination of advanced techniques is proved useful for enhancing our understanding of the interfacial chemistry between fibers and the binding matrix. This level of knowledge facilitates the engineering of composite systems through the manipulation of their nanostructure.

36 MATERIALS SCIENCE↗