Engineering topics

Algozeeb, Wala A.

Publications and source records attributed to Algozeeb, Wala A..

6 records

DOE OSTI2022

Waste plastic- and coke-derived flash graphene as lubricant additives

Lubricants play an essential role in reducing wear in mechanical systems. Carbon nanomaterial additives, such as graphene, have been found to significantly improve tribological performance when used as lubricant additives. Here, in this study, post-consumer plastic and metallurgical coke are converted into turbostratic flash graphene (FG) through flash Joule heating (FJH). The FG is then added to either poly(alpha olefin) 6 or 9 (PAO 6 or PAO 9). Adding waste plastic-derived FG (WPFG) and metallurgical coke-derived FG (MCFG) to lubricants resulted in a significant decrease in the coefficient of friction (CoF), wear scar diameter (WSD), and roughness during four-ball testing. WPFG and MCFG decrease the CoF in PAO 9 by 6% and 9% at 0.1 mg mL -1 , respectively, and in PAO 6 by 23% and 6% at 0.5 mg mL -1 , respectively. WPFG and MCFG decrease the WSD of steel balls in PAO 9 by 14% and 8% at 0.5 mg mL -1 , respectively, and in PAO 6 by 12% and 14% at 0.5 mg mL -1 , respectively, by forming a coating-like layer between the metal surfaces. Roughness decreased by 38% and 32% for WPFG and MCFG in PAO 6, respectively, and by 35% and 29% for WPFG and MCFG in PAO 9, respectively. Finally, preliminary life cycle analyses demonstrate that production of FG produces up to 99% less greenhouse gas emissions, requires 98% less energy, and consumes 99.9% less water when compared to conventional production techniques of graphene. Hence, metallurgical coke and waste plastic are shown to be ready feedstocks for high-quality FG lubricant additives.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Plastic Waste Product Captures Carbon Dioxide in Nanometer Pores

We discuss, plastic waste (PW) and increasing atmospheric carbon dioxide (CO 2 ) levels are among the top environmental concerns presently facing humankind. With an ambitious 2050 zero-CO 2 emissions goal, there is a demand for economical CO 2 capture routes. Here we show that the thermal treatment of PW in the presence of potassium acetate yields an effective carbon sorbent with pores width of 0.7–1.4 nm for CO 2 capture. The PW to carbon sorbent process works with single or mixed streams of polyolefin plastics. The CO 2 capacity of the sorbent at 25 °C is 17.0 ± 1.1 wt % (3.80 ± 0.25 mmol g –1 ) at 1 bar and 5.0 ± 0.6 wt % (1.13 ± 0.13 mmol g –1 ) at 0.15 bar, and it regenerates upon reaching 75 ± 5 °C. The CO 2 capture cost from flue gas via this technology is estimated to be <$21 ton –1 CO 2 , much lower than competing CO 2 capture technologies. Hence, this PW-derived carbon material should find utility in the capture of CO 2 from point sources of high CO 2 emissions while providing a use for otherwise deleterious PW.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Ultrafast and Controllable Phase Evolution by Flash Joule Heating

Flash Joule heating (FJH), an advanced material synthesis technique, has been used for the production of high-quality carbon materials. Direct current discharge through the precursors by large capacitors has successfully converted carbon-based starting materials into bulk quantities of turbostratic graphene by the FJH process. However, the formation of other carbon allotropes, such as nanodiamonds and concentric carbon materials, as well as the covalent functionalization of different carbon allotropes by the FJH process, remains challenging. Here, we report the solvent-free FJH synthesis of three different fluorinated carbon allotropes: fluorinated nanodiamonds, fluorinated turbostratic graphene and fluorinated concentric carbon. This is done by millisecond flashing of organic fluorine compounds and fluoride precursors. Spectroscopic analysis confirms the modification of the electronic states and the existence of various short-range and long-range orders in the different fluorinated carbon allotropes. As a result, the flash time-dependent relationship is further demonstrated to control the phase evolution and product compositions.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Millisecond Conversion of Metastable 2D Materials by Flash Joule Heating

Controllable phase engineering is vital for precisely tailoring material properties since different phase structures have various electronic states and atomic arrangements. Rapid synthesis of thermodynamically metastable materials, especially two-dimensional metastable materials, with high efficiency and low cost remains a large challenge. Here we report flash Joule heating (FJH) as an electrothermal method to achieve the bulk conversion of transition metal dichalcogenides, MoS 2 and WS 2 , from 2H phases to 1T phases in milliseconds. The conversions can reach up to 76% of flash MoS 2 using tungsten powder as conductive additive. Different degrees of phase conversion can be realized by controlling the FJH conditions, such as reaction duration and additives, which allows the study of ratio-dependent properties. First-principles calculations confirm that structural processes associated with the FJH, such as vacancy formation and charge accumulation, result in stabilization of the 1T phases. Furthermore, FJH offers rapid access to bulk quantities of the hitherto hard-to-access 1T phases, a promising method for further fundamental research and diverse applications of metastable phases.

2D materials↗

DOE OSTI2020

Flash Graphene from Plastic Waste

In this work, an approach to upcycling plastic waste (PW) products is presented. The method relies on flash Joule heating (FJH) to convert PW into flash graphene (FG). In addition to FG, the process results in the formation of carbon oligomers, hydrogen, and light hydrocarbons. In order to make high quality graphene, a sequential alternating current (AC) and direct current (DC) flash is used. Here, the FJH process requires no catalyst and works for PW mixtures, which makes the process suitable for handling landfill PW. The energy required to convert PW to FG is ~ 23 kJ/g or ~ $125 in electricity per ton of PW, potentially making this process economically attractive for scale-up. The FG was characterized by Raman spectroscopy and had a I 2D /I G peak ratio up to 6 with a low-intensity D band. Moreover, transmission electron microscopy and X-ray diffraction analysis show that the FG is turbostratic with an interlayer spacing of 3.45 Å. The large interlayer spacing will facilitate its dispersion in liquids and composites. Analysis of FG dispersions in 1% Pluronic aqueous solution shows that concentrations up to 1.2 mg/mL can be achieved. The carbon oligomers that distilled from the process were characterized by Fourier-transform infrared spectroscopy and have chemical structures similar to the starting PW. Initial analysis of gas phase products shows the formation of considerable amounts of hydrogen along with other light hydrocarbons. Since graphene is naturally occurring and it shows a low toxicity profile, this could be an environmentally beneficial method to upcycle PE.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Flash Graphene Morphologies

Flash Joule heating (FJH) can convert almost any carbon-based precursor into bulk quantities of graphene. This work explores the morphologies and properties of flash graphene (FG) generated from carbon black. It is shown that FG is partially comprised of sheets of turbostratic FG (tFG) that have a rotational mismatch between neighboring layers. The remainder of the FG is wrinkled graphene sheets that resemble non-graphitizing carbon. To generate high quality tFG sheets, a FJH duration of 30 – 100 ms is employed. Beyond 100 ms, the turbostratic sheets have time to AB-stack and form bulk graphite. Atomistic simulations reveal that generic thermal annealing yields predominantly wrinkled graphene which displays minimal to no alignment of graphitic planes, as opposed to the high-quality tFG that might be formed under the direct influence of current conducted through the material. As a result, the tFG was easily exfoliated via shear, hence the FJH process has the potential for bulk production of tFG without the need for pre-exfoliation using chemicals or high energy mechanical shear.

01 COAL, LIGNITE, AND PEAT↗