Engineering Papers⌕ Search

Engineering topics

Ahuja, K. K.

Publications and source records attributed to Ahuja, K. K..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Screech tones from free and ducted supersonic jets

It is well known that screech tones from supersonic jets are generated by a feedback loop. The loop consists of three main components. They are the downstream propagating instability wave, the shock cell structure in the jet plume, and the feedback acoustic waves immediately outside the jet. Evidence will be presented to show that the screech frequency is largely controlled by the characteristics of the feedback acoustic waves. The feedback loop is driven by the instability wave of the jet. Thus the tone intensity and its occurrence are dictated by the characteristics of the instability wave. In this paper the dependence of the instability wave spectrum on the azimuthal mode number (axisymmetric or helical/flapping mode, etc.), the jet-to-ambient gas temperature ratio, and the jet Mach number are studied. The results of this study provide an explanation for the observed screech tone mode switch phenomenon (changing from axisymmetric to helical mode as Mach number increases) and the often-cited experimental observation that tone intensity reduces with increase in jet temperature. For ducted supersonic jets screech tones can also be generated by feedback loops formed by the coupling of normal duct modes to instability waves of the jet. The screech frequencies are dictated by the frequencies of the duct modes. Super resonance, resonance involving very large pressure oscillations, can occur when the feedback loop is powered by the most amplified instability wave. It is proposed that the observed large amplitude pressure fluctuations and tone in the test cells of Arnold Engineering Development Center were generated by super resonance. Estimated super-resonance frequency for a Mach 1.3 axisymmetric jet tested in the facility agrees well with measurement.

Tam, C. K. W.↗
NASA NTRS1993

Strategic planning for aircraft noise route impact analysis: A three dimensional approach

The strategic routing of aircraft through navigable and controlled airspace to minimize adverse noise impact over sensitive areas is critical in the proper management and planning of the U.S. based airport system. A major objective of this phase of research is to identify, inventory, characterize, and analyze the various environmental, land planning, and regulatory data bases, along with potential three dimensional software and hardware systems that can be potentially applied for an impact assessment of any existing or planned air route. There are eight data bases that have to be assembled and developed in order to develop three dimensional aircraft route impact methodology. These data bases which cover geographical information systems, sound metrics, land use, airspace operational control measures, federal regulations and advisories, census data, and environmental attributes have been examined and aggregated. A three dimensional format is necessary for planning, analyzing space and possible noise impact, and formulating potential resolutions. The need to develop this three dimensional approach is essential due to the finite capacity of airspace for managing and planning a route system, including airport facilities. It appears that these data bases can be integrated effectively into a strategic aircraft noise routing system which should be developed as soon as possible, as part of a proactive plan applied to our FAA controlled navigable airspace for the United States.

Bragdon, C. R.↗
NASA NTRS1993

Measured acoustic characteristics of ducted supersonic jets at different model scales

A large-scale (about a 25x enlargement) model of the Georgia Tech Research Institute (GTRI) hardware was installed and tested in the Propulsion Systems Laboratory of the NASA Lewis Research Center. Acoustic measurements made in these two facilities are compared and the similarity in acoustic behavior over the scale range under consideration is highlighted. The study provide the acoustic data over a relatively large-scale range which may be used to demonstrate the validity of scaling methods employed in the investigation of this phenomena.

Jones, R. R., III↗
NASA NTRS1993

Screech tones from free and ducted supersonic jets

The dependence of the instability wave spectrum on azimuthal mode number, the jet to ambient gas temperature ratio, and the jet Mach number is studied. It is shown that the switch of the dominant screech mode (axisymmetric to helical/flapping) as Mach number increases is due to the switch in dominance of the corresponding mode of instability waves. Super-resonance can occur when the feedback loop is powered by the most amplified instability wave. It is suggested that the large amplitude pressure fluctuations and tone in the test cells are generated by super-resonance.

Tam, C. K. W.↗
NASA NTRS1992

Acoustic interactions between an altitude test facility and jet engine plumes: Theory and experiments

The overall objective of the described effort was to develop an understanding of the physical mechanisms involved in the flow/acoustic interactions experienced in full-scale altitude engine test facilities. This is done by conducting subscale experiments and through development of a theoretical model. Model cold jet experiments with an axisymmetric convergent nozzle are performed in a test setup that stimulates a supersonic jet exhausting into a cylindrical diffuser. The measured data consist of detailed flow visualization data and acoustic spectra for a free and a ducted plume. It is shown that duct resonance is most likely responsible by theoretical calculations. Theoretical calculations also indicate that the higher discrete tones observed in the measurements are related to the screech phenomena. Limited experiments on the sensitivity of a free 2-D, C-D nozzle to externally imposed sound are also presented. It is shown that a 2-D, C-D nozzle with a cutback is less excitable than a 2-D C-D nozzle with no cutback. At a pressure ratio of 1.5 unsteady separation from the diverging walls of the nozzle is noticed. This separation switches from one wall to the opposite wall thus providing an unsteady deflection of the plume. It is shown that this phenomenon is related to the venting provided by the cutback section.

Ahuja, K. K.↗
NASA NTRS1992

Supersonic jet noise reduction by coaxial rectangular nozzles

A physical understanding of noise reduction mechanisms in supersonic, single, and coaxial rectangular jets is quantified and obtained, with emphasis on shock noise reduction. For all conditions, corresponding acoustic measurements for an equivalent round jet are also obtained so that the noise characteristics of the two types of jets can be compared directly to quantify the noise reductions. Comparisons are thus provided for a single rectangular nozzle vs a single equivalent round nozzle, and a coaxial rectangular nozzle vs an equivalent round nozzle. It is shown that different operating conditions and nozzle arrangements for the same thrust, total exit area, and mass flow rate can produce different noise levels. With at least one stream operated supersonically, the coaxial rectangular nozzle operated in the inverted-velocity profile is always quieter than in the normal velocity profile mode for the same thrust, exit area, and mass flow rate. In general, the coaxial rectangular nozzle is shown to be quieter than an equivalent circular nozzle only for those conditions for which both nozzles are operated supersonically.

Ahuja, K. K.↗
NASA NTRS1992

A review of crack propagation under unsteady loading

The theories and research current available on crack propagation under unsteady loadings, especially those of acoustic origin, are reviewed. Since the original theories on fatigue failure did not account for random loading conditions, modified theories which provide statistical methods for evaluating the random loading have emerged. The impact of acoustic fatigue in the aerospace industry, basic principles such as fatigue crack initiation and propagation and load interactions, and testing procedures are discussed. Attention is also given to metal and metal alloy structures, fiber-reinforced composites and nonmetallic structures, short crack growth, and the effects of temperature, moisture, and corrosion on structures. Suggestions for future research in this field are presented, namely, studies on the effect of 'snap-through' response and associated crack growth patterns, studies in microcrack and 'small crack'; propagation under unsteady loading conditions, and the development of an accurate analytical model to predict acceleration and retardation effects in fatigue crack growth under random loading conditions.

Bryan, H. H.↗
NASA NTRS1990

An evaluation of various concepts of reducing supersonic jet noise

Acoustic and flow visualization data from nozzles mounted on the same facility were acquired, and a total of 10 different concepts of jet noise suppression were evaluated relative to one another and also a round nozzle. All nozzles had the same exit area. The suppressors included noncircular shapes; nozzles fitted with notches, tabs, and ejectors; and coaxial rectangular nozzles. Narrow-band noise data were acquired by a microphone located in the plane of the jet exit. In general, it is found that, for a constant exit area, the round nozzle is the noisiest. Just about any modification of this round nozzle around its periphery reduces the broadband shock-associated noise and, in most instances, modifies the screech frequency and levels. Coaxial rectangular nozzles, nozzles fitted with two tabs and operated with ejectors, and a rectangular C-D nozzles with perforated walls are identified to be the most promising concepts worthy of further investigation.

Ahuja, K. K.↗
NASA NTRS1990

Theoretical model of discrete tone generation by impinging jets

A new feedback mechanism is proposed for discrete tone generation by impinging jets. It is suggested that the feedback is achieved by upstream-propagating waves associated with the lowest-order intrinsic neutral wave modes of the jet flow. These wave modes have well-defined radial and azimuthal pressure and velocity distributions, which are determined by the mean flow of the jets in the case of the Kelvin-Helmholtz instability waves. The model proposed here allows the prediction of the average Strouhal number of impingement tones as a function of the jet Mach number.

Tam, Christopher K. W.↗
NASA NTRS1990

Enhancement of mixing in a rectangular jet by mechanical tabs

This effort was conducted to obtain additional test data/configurations required to better understand the effects of tab length and width on jet mixing enhancement for a rectangular nozzle. The configurations tested were a six-tab configuration defined by NASA, a full-height tab configuration, and two-tab configurations with selected tab lengths and widths. Additional test data were also required for all candidate configurations to better interpret the data. Test data from this effect are presented. On the basis of these data, the following general observations were noted: The six-tab rectangular nozzle configuration provided a lower peak velocity than either the two-tab or four-tab configuration; and the rectangular nozzle with a full-height tab had about the same peak velocity as the two-tab configuration; however, the full-height tab configuration had a somewhat lower centerline velocity.

Brown, W. H.↗
NASA NTRS1989

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 1: Results and discussion

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. The conclusions derived were: (1) intrusive probes can produce significant errors in the measurements of the velocity of jets if they are large in diameter and penetrate beyond the jet center; (2) rectangular jets without tabs, compared to circular jets of the same exit area, provide faster jet mixing; and (3) further mixing enhancement is possible by using mechanical tabs.

Brown, W. H.↗
NASA NTRS1989

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 2: Tabulated data

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. This volume contains tabulated data for each of the data runs cited in Volume 1. Baseline characteristics, mixing modifications (subsonic and supersonic, heated and unheated) and miscellaneous charts are included.

Brown, W. H.↗
NASA NTRS1988

Acoustically excited heated jets. 1: Internal excitation

The effects of relatively strong upstream acoustic excitation on the mixing of heated jets with the surrounding air are investigated. To determine the extent of the available information on experiments and theories dealing with acoustically excited heated jets, an extensive literature survey was carried out. The experimental program consisted of flow visualization and flowfield velocity and temperature measurements for a broad range of jet operating and flow excitation conditions. A 50.8-mm-diam nozzle was used for this purpose. Parallel to the experimental study, an existing theoretical model of excited jets was refined to include the region downstream of the jet potential core. Excellent agreement was found between theory and experiment in moderately heated jets. However, the theory has not yet been confirmed for highly heated jets. It was found that the sensitivity of heated jets to upstream acoustic excitation varies strongly with the jet operating conditions and that the threshold excitation level increases with increasing jet temperature. Furthermore, the preferential Strouhal number is found not to change significantly with a change of the jet operating conditions. Finally, the effects of the nozzle exit boundary layer thickness appear to be similar for both heated and unheated jets at low Mach numbers.

Lepicovsky, J.↗
NASA NTRS1988

Acoustically excited heated jets. 2: In search of a better understanding

The second part of a three-part report on the effects of acoustic excitation on jet mixing includes the results of an experimental investigation directed at resolving the question of poor excitability of some of the heated jets. The theoretical predictions discussed in Part 1 are examined to find explanations for the observed discrepancies between the measured and the predicted results. Additional testing was performed by studying the self excitation of the shock containing hot jets and also by exciting the jet by sound radiated through source tubes located externally around the periphery of the jet. The effects of nozzle-exit boundary layer conditions on jet excitability was also investigated. It is concluded that high-speed, heated jet mixing rates and consequently also the jet excitability strongly depends on nozzle exit boundary layer conditions.

Lepicovsky, J.↗
NASA NTRS1988

Acoustically excited heated jets. 3: Mean flow data

This is Part 3 of a report on the excitability of heated jets under the influence of acoustic excitation. The effects of upstream internal acoustic excitation on jet mixing were described in Part 1. Part 2 described the effects of external excitation on flow mixing. Part 3 contains quantitative results from the measurements of mean Mach number and temperature and consists of radial profiles and centerline distributions measured at selected jet operating conditions for internally excited and unexcited jets. The mean flow data are presented in both graphical and tabulated forms. For the sake of completeness, this part contains temperature probe calibration curves also.

Lepicovsky, J.↗
NASA NTRS1988

Aeroacoustics of advanced STOVL aircraft plumes

This paper summarizes a basic and well-controlled experimental study involving flow visualization and noise measurements to define the acoustic and flow fields of single plumes impinging on a simulated ground plane. The flow visualization was made by strobing a laser light source at the discrete frequencies generated by the impingement of the jets and measured by a nearfield microphone. This enabled visualization of instability waves generated by the interaction between the plumes and the sound generated during impingement, and also by dynamic coupling between the two plumes. These data were acquired as a function of distance between the ground and the nozzle exit. Nearfield acoustic data were acquired simultaneously. Data for nozzle diameters of 0.265 in. and 0.4 in. are described. For selected nozzles, effects of exit boundary layer characteristics and nozzle protrusion through a simulated aircraft body are also presented.

Ahuja, K. K.↗