Engineering Papers⌕ Search

Engineering topics

Ahrenkiel, Phil

Publications and source records attributed to Ahrenkiel, Phil.

Quantitative order-parameter measurement in lattice-mismatched AlInP using precession electron diffraction

Precession electron diffraction (PED) was used to measure the long-range order parameter in lattice-mismatched AlInP epitaxial films under investigation for solid-state-lighting applications. Both double- and single-variant films grown at 620, 650, and 680°C were analyzed in TEM cross-section. PED patterns were acquired in selected-area-diffraction mode through external microscope control using serial acquisition, which allows inline image processing. The integrated peak intensities from experimental patterns were fit using dynamical simulations of diffraction from the ordered domain structures. Included in the structure-factor calculations were mean atomic displacements of the anions (P) due to ordering, which were found by valence-force-field calculations to have a nearly linear dependence on order parameter. A maximum order parameter of S = 0.36 was measured for a double-variant specimen grown at 650°C.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Applications of plasma-enhanced metalorganic chemical vapor deposition

The use of plasma enhancement for growth of III-V compound semiconductor materials by metalorganic chemical vapor deposition (MOCVD) is examined, to improve control of microstructure, develop understanding of the underlying growth mechanisms, and expand the range of materials combinations for photovoltaic and solid-state lighting applications. Whereas plasma is commonly used with group-IV materials, such as silicon, few studies have examined the impact of plasma-enhanced MOCVD (PE-MOCVD) for III-V materials growth. PE-MOCVD provides improved decomposition of metalorganic precursors, which is driven by hydrogen plasma to augment hydride reactions and thermal pyrolysis, but plasma generation requires low reactor pressure. We have demonstrated elemental Al films grown by PE-MOCVD, which show distinct crystallographic texturing, and assume epitaxial microstructure upon post-growth annealing. We also demonstrate PE-MOCVD of GaAs at temperatures as low as 300 °C. With increasing radio-frequency power, the GaAs growth rate shows a transition from power limited to mass-transport limited. PE-MOCVD grown Ga 0.5 In 0.5 P shows no detectable spontaneous atomic ordering, which offers a mechanism to form order/disorder unicompositional heterostructures, without temperature change or impurity incorporation. In its current implementation, PE-MOCVD grown films have shown microstructural degradation, that we attribute to direct plasma exposure during growth. Improvements in the system design and growth sequences are at the focus of on-going efforts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Orientations of Al4C3 and Al films grown on GaAs substrates

We present that a method for growth of aluminum epilayers on III-V substrates using metalorganic chemic vapor deposition (MOCVD) processes could be beneficial for optoelectronic and photovoltaic device fabrication. However, de- position from common precursors under standard MOCVD conditions results in polycrystalline Al 4 C 3 . Both Al 4 C 3 films grown on GaAs (100) substrates, and those grown on GaAs (111) B substrates, show strong alignment of the rhombohedral [110] for the Al 4 C 3 crystallites with the in-plane GaAs<110>directions. However, by using plasma-enhanced MOCVD at low growth temperatures, elemental Al can be deposited. Al growth by this method on (001), (111) B and (110) GaAs substrates gave textured, polycrystalline films. In all cases, the Al crystallites are primarily oriented with a<110>aligned with an in-plane<110>of the substrate at initial growth stages. Lastly, these insights may lead towards growth of large-grained or epitaxial Al films.

14 SOLAR ENERGY↗

Defect reduction by liquid phase epitaxy of germanium on single-crystalline-like germanium templates on flexible, low-cost metal substrates

Single-crystalline-like germanium (Ge) templates were demonstrated on low-cost, flexible metal substrates and have been used to fabricate III–V materials and devices for photovoltaics and flexible electronics applications. However, these Ge templates, fabricated by magnetron sputtering or plasma enhanced chemical vapor deposition, contain a high density of defects. In order to improve the performance of optoelectronic devices made using the Ge templates, a homo-epitaxial Ge layer has been additionally grown by a liquid phase epitaxy (LPE) method. The LPE Ge layer is composed of significantly larger grains (~26 μm) compared to that of the Ge template (~200 nm). This large size of the LPE Ge grains effectively reduces the volume fraction of grain boundaries. The LPE Ge shows an out-of-plane texture Δω of ~0.63° and an in-plane texture ΔΦ of ~1.26°, which signify improvements of ~39.3% and ~76.6% compared to that of the vapor-deposited Ge template, respectively. Further, the LPE Ge is strain free, compared to the strained Ge template hetero-epitaxially grown on cerium oxide. Defects caused by low-angle grain boundaries, impurities and strain relaxation in the Ge template are found to be suppressed in the LPE Ge. The threading dislocation density is roughly estimated to be ~5 × 10 6 cm -2 in the LPE Ge compared to ~1 × 10 10 cm -2 in the Ge template.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

FinalTechRep_DE_EE0007363_15

The primary objective of the project was to develop Ga 0.82 In 0.18 As (GaInAs) solar cells grown on epilayers of elemental Al. At this composition, GaInAs has a nearly optimal bandgap (1.16 eV) for a single-junction photovoltaic device. However, GaInAs lacks a convenient, lattice-matched substrate, restricting most investigations to metamorphic structures. The metal Al is, in fact, precisely lattice-matched to GaInAs in the orientation GaInAs (001)[100]||Al(001)[110]. At present, however, epi-ready Al substrates are not readily available commercially and are subject to oxidation. However, epitaxial Al buffer layers could enable control of defect generation, thermal and light management, and rapid epitaxial lift-off for ultrathin devices.

30 DIRECT ENERGY CONVERSION↗

USD Catalysis Group for Alternative Energy

The South Dakota Catalysis Group (SDCG) is a collaborative project with mission to develop advanced catalysts for energy conversion with two primary goals: (1) develop photocatalytic systems in which polyfunctionalized TiO2 are the basis for hydrogen/oxygen synthesis from water and sunlight (solar fuels group), (2) develop new materials for hydrogen utilization in fuel cells (fuel cell group). In tandem, these technologies complete a closed chemical cycle with zero emissions.

14 SOLAR ENERGY↗