Engineering topics

Ahmed, Kareem

Publications and source records attributed to Ahmed, Kareem.

12 records

DOE OSTI2022

Improving NO x Entitlement with Axial Staging

Manufacturers are constantly under pressure to increase the efficiency of air breathing gas turbines for the next generation of ground based combined cycle power plants without a significant increase in NO x emissions. Axially staging some of the fuel and air is one method manufacturers are exploring to increase the firing temperature with a minimal NO x increase. This project used a high-pressure combustion facility to systematically explore the axial stage design space at conditions relevant to engine manufacturers. Chemiluminescence and PIV images of the reacting jets were obtained as well as exit emissions. This data was used to create correlations for reacting jets-in-crossflow, analogous to what currently exists for non-reacting jets-in-crossflow. Two CFD programs were used to model these results to quantifying the accuracy of the codes and help elucidate the underlying physics that governs the high-pressure reacting jet in crossflow. This report indicates a change in flame/flow-field behavior, and emissions characteristics with increasing pressure from 1-5.5 atm. Additionally, the effects of preheating and premixing the axial jet are explored at various conditions and show increased jet liftoff leads to a decrease in NO x emissions.

03 NATURAL GAS↗

DOE OSTI2022

Controlling pollutant emissions in a high-pressure combustor with fuel-diluent blending

This paper investigates the formation of nitric oxide (NO) and carbon monoxide (CO) emissions as a function of nitrogen (N 2 ) or carbon dioxide (CO 2 ) diluent content, added to a premixed reacting jet in crossflow. Here, reaction characteristics of a rich methane-air jet injected into a lean vitiated crossflow were analyzed at an elevated pressure of 5 atm. The jet was pre-heated and enriched with 0%, 15%, 30%, and 50% mass fraction to quantify the effect on pollutant emissions. Simulated results of the full chemistry Star-CCM+CFD model were verified with data taken in the experimental high-pressure combustion facility, which provides pressure, temperature and velocity profiles, as well as line-of-sight chemiluminescence and exit emission measurements. The analysis revealed the significant influence of the diluent to delay axial combustion; this mixing delay increased the axial flame lift-off and controlled any thermal ignition limitations. Increasing the diluent content increased the timescale for the flame to stabilize, which allowed for greater entrainment of crossflow oxidizer into the axial jet stream, and led to decreased pollutant emissions. Hence, crossflow entrainment is a critical driving force at high diluent content. Local nitric oxide (NO) emission formation in the axial stage was predicted numerically, showing the correlation between diluent addition, axial heat release, and the formation of nitric oxide pollution. The high diluent levels leaned out the jet mixture and delayed axial combustion, while reducing prompt and thermal NOx by mitigating flame hotspots and minimizing the timescale that the products remain at high temperatures.

03 NATURAL GAS↗

DOE OSTI2021

Carbon and Hydrocarbon Particle Seeding in Air-Breathing Rotating Detonation Engine

Within the power generation community, the rotating detonation engine (RDE) is only growing in popularity with its increased performance, simple mechanism, and operation. Although significant testing is underway to characterize the RDE for integration with conventional gas turbines, this entire system is still at a relatively low technology readiness level. In the midst of RDE research, there is an initiative to understand solid particle seeding effects in the detonation performance. Under investigation at the University of Central Florida is a Department of Energy (DOE) 15.24 cm (6 in.) RDE, with a solid particle seeder in parallel with its H2 and air flow lines. Previous work on this system involved carbon particle detonation; however, the tested particles were taken one step further to include more sustainable, greener hydrocarbon particles. Testing of powdered sugar, peanut flour, and cornstarch, along with previous carbon black tests have shown not only successful detonability, but a noticeable effect on the detonation wave dynamics. Side-by-side with a particle burning model being developed, an operational map can be determined for the hydrocarbon particles particularly, which can be tuned with the local flow conditions to achieve peak operability while replacing fuels with sustainable alternatives that could even be grown.

Engineering↗

DOE OSTI2021

Preheating and premixing effects on NO x emissions in a high-pressure axially staged combustor

NO x emissions remain a primary concern for modern and future gas turbines, particularly as we progress towards a net-zero carbon future. It is critical to identify novel strategies to mitigate environmental pollutants for both modern turbines operated on natural gas and future turbines projected to use carbon-free fuels (such as hydrogen). In the current study, NO x emissions of a reacting methane-air jet in a vitiated crossflow are experimentally investigated in a model axially staged combustor at 5 atm. The combustion products from the main stage combustor flow into the axial stage at temperatures ranging from 1580 to 1650 °C. The axial stage contains a reacting jet in crossflow, which provides an overall temperature rise ranging from 50 to 220 °C to generate exit temperatures similar to gas turbine engines. The focus of this paper is to explore the effects of flame liftoff and ignition timescales on the NO x contribution of this secondary jet. This is done by varying the premixed level and preheat temperature of the axial jet. The effects are explored at different momentum flux ratios (J), jet equivalence ratios (φ jet ), exit temperatures (T exit ), and main stage (headend) temperatures (T HE ). High-speed CH* chemiluminescence imaging is employed for each test case to determine the flame stabilization point. For a given temperature rise and combustor exit temperature, an increase in ignition delay was observed with a decrease in jet temperature. This provided a NO x benefit, particularly for jets that are injected at or close to an ignitable mixture fraction. Similarly, the coaxial injector caused a significant ignition delay compared to the fully premixed injector; this also led to a NO x benefit. Overall, the results show that a thermally driven delay in the axial stage provides a greater NO x reduction than a mixing delay.

03 NATURAL GAS↗

DOE OSTI2021

Carbon-Based Multi-Phase Rotating Detonation Engine

Abstract This article focuses on extending an H2/air rotating detonation engine's detonability limits by introducing solid carbon particles into the combustor. Carbon black particles consisting of 1% volatility and a carbon concentration of 99% were used as a solid-phase mixing agent for enhanced reaction wave dynamics. Carbon black was found to sustain detonations over multiple operational regimes formerly unattainable without carbon particles. The experiments confirm that detonations were attainable over a wide range of operational parameters, including the total mass flux flowing through the annulus (≅120–270 kg/s m2), the hydrogen/air equivalence ratios (0.65–1.0), and carbon additions (0–20 g). Chemiluminescence imaging was used to visualize the detonation wave within the annulus, quantify detonation wave velocities, and define a detonability map. The detonability map demonstrates the advantage of carbon addition, shows that detonation-based combustion can be sustained at leaner equivalence ratios, reduces hydrogen consumption dependency. The detonation wave velocities decreased as the H2/air equivalence ratio was reduced, where, in general, the detonation wave velocities decreased with respect to the Chapman–Jouguet velocity, suggesting a decrease in the detonation waves efficiency with reduced H2 concentrations. However, an extraordinary phenomenon was witnessed at very lean H2/air equivalence ratios and low mass flux conditions, where the detonation wave velocity increased upward of 100 m/s. This variation is a direct effect of the carbon particles, which drive the detonation wave. Thus, the results demonstrate that carbon particles’ addition provides an economically feasible solution to sustain high-efficiency energy production.

Energy & Fuels↗

NASA NTRS2020

An Experimental Validation of a Revised Paschen's Law Relating to the ESD of Aerospace Vehicle Surfaces

This work seeks to experimentally validate a modified Paschen law which takes into account the effects of electron-ion pair removal between two electrodes within a dynamic gas medium. A test facility has been designed and fabricated in order to create supersonic flow conditions within the test section. Custom designed electrodes are mounted into the test section at desired gap distances. A power supply is utilized to charge the electrodes until discharge occurs. The discharge voltage of the electrode is recorded over a range of pressures within the test section. An operational pressure range is calculated using isentropic flow and normal shock relations at the desired Mach numbers. These values are plotted against the modified Paschen curve as a function of Mach number, electrode gap distance, and pressure as a means of validation.

ESD↗

NASA NTRS2019

Revision of Paschen's Law Relating to the ESD of Aerospace Vehicle Surfaces

The purpose of this work is to develop a form of Paschen's law that takes into account the flow of gas past electrode surfaces. This work was performed under a NASA Science Innovation Fund (SIF) project at the Kennedy Space Center in collaboration with the University of Central Florida. In 2010 the Electrostatics and Surface Physics Laboratory (ESPL) at the Kennedy Space Center performed an electrostatic safety analysis on the flight termination system (FTS) antenna for the Ares I rocket. Paschen's law, derived by Friedrich Paschen in 1889 to relate sparking voltage to gas pressure and electrode separation, does not take into account the effect of flowing gas between the electrodes. The safety of the FTS housing to triboelectric charging was shown only after extensive laboratory testing. Potential benefits are of a form of Paschen's law that considers gas velocity. This work is applicable to current and planned rockets and aerospace vehicles and could lead to possible relaxation of electrostatic launch criteria. Launch aborts can cost up to about a million US dollars depending on the vehicle. [ElectroStatic Discharge (ESD)]

Paschen↗

NASA NTRS2017

Revision of Paschen's Law Relating to the ESD of Aerospace Vehicle Surfaces

The purpose of this work is to develop a version of Paschen's law that takes into account the flow of ambient gas past electrode surfaces. Paschen's law does not consider the flow of gas past an aerospace vehicle whose surfaces may be triboelectrically charged by dust or ice crystal impingement while traversing the atmosphere. The basic hypothesis of this work is that the number of electron-ion pairs created per unit distance between electrode surfaces is mitigated by the electron-ion pairs removed per unit distance by the flow of gas. The revised theoretical model must be a function of the mean velocity vxm of the ambient gas and reduce to Paschen's law when the mean velocity is zero. A new theoretical formulation of Paschen's law, taking into account the Mach number and compressible dynamic pressure, derived by the authors, will be discussed. This equation has been evaluated by wind tunnel experimentation. Initial data of the baseline wind tunnel experiments show results consistent with the hypothesis. This work may enhance the safety of aerospace vehicles through a redefinition of electrostatic launch commit criteria. It is also possible for new products, such as antistatic coatings, to be formulated based on this data.

electrostatic↗

NASA NTRS2017

Revision of Paschen's Law Relating to the ESD of Aerospace Vehicle Surfaces

The purpose of this work is to develop a version of Paschens law that takes into account the flow of ambient gas past electrode surfaces. Paschens law does not consider the flow of gas past an aerospace vehicle whose surfaces may be triboelectrically charged by dust or ice crystal impingement while traversing the atmosphere. The basic hypothesis of this work is that the number of electron-ion pairs created per unit distance between electrode surfaces is mitigated by the electron-ion pairs removed per unit distance by the flow of gas. The revised theoretical model must be a function of the mean velocity vxm of the ambient gas and reduce to Paschens law when the mean velocity is zero. A new theoretical formulation of Paschens law, taking into account the Mach number and compressible dynamic pressure, derived by the authors, will be discussed. This equation has been evaluated by wind tunnel experimentation. Initial data of the baseline wind tunnel experiments show results consistent with the hypothesis. This work may enhance the safety of aerospace vehicles through a redefinition of electrostatic launch commit criteria. It is also possible for new products, such as antistatic coatings, to be formulated based on this data.

discharge↗

NASA NTRS2017

Dynamic Gas Flow Effects on the ESD of Aerospace Vehicle Surfaces

The purpose of this work is to develop a version of Paschen's Law that takes into account the flow of ambient gas past electrode surfaces. Paschen's Law does not consider the flow of gas past an aerospace vehicle, whose surfaces may be triboelectrically charged by dust or ice crystal impingement while traversing the atmosphere. The basic hypothesis of this work is that the number of electron-ion pairs created per unit distance between electrode surfaces is mitigated by the electron-ion pairs removed per unit distance by the flow of gas. The revised theoretical model must be a function of the mean velocity, v (sub xm), of the ambient gas and reduce to Paschen's law when the gas mean velocity, v (sub xm) equals 0. A new theoretical formulation of Paschen's Law, taking into account the Mach number and dynamic pressure, derived by the authors, will be discussed. This equation was evaluated by wind tunnel experimentation whose results were consistent with the model hypothesis.

Electrostatic↗

NASA NTRS2016

Dynamic Gas Flow Effects on the ESD of Aerospace Vehicle Surfaces

The purpose of this work is to develop a dynamic version of Paschen's Law that takes into account the flow of ambient gas past aerospace vehicle surfaces. However, the classic Paschen's Law does not take into account the flow of gas of an aerospace vehicle, whose surfaces may be triboelectrically charged by dust or ice crystal impingement, traversing the atmosphere. The basic hypothesis of this work is that the number of electron-ion pairs created per unit distance by the electric field between the electrodes is mitigated by the electron-ion pairs removed per unit distance by the flow of gas. The revised Paschen equation must be a function of the mean velocity, v(sub xm), of the ambient gas and reduces to the classical version of Paschen's law when the gas mean velocity, v(sub xm) = 0. New formulations of Paschen's Law, taking into account Mach number and dynamic pressure, derived by the authors, will be discussed. These equations will be evaluated by wind tunnel experimentation later this year. Based on the results of this work, it is hoped that the safety of aerospace vehicles will be enhanced with a redefinition of electrostatic launch commit criteria. It is also possible that new products, such as new anti-static coatings, may be formulated from this data.

Paschens Law↗

NASA NTRS2016

Dynamic Gas Flow Effects on the ESD of Aerospace Vehicle Surfaces

Electrostatic Discharge↗