Engineering Papers⌕ Search

Engineering topics

Ahmadi, Goodarz

Publications and source records attributed to Ahmadi, Goodarz.

At least 19 records

Computational Modeling of Proppants Transport in Rock Fractures

Presentation describing the direct numerical simulations (DNS) of fluid and particulate transport through rough-walled rock fractures showing transport properties of proppants as a function of fracture properties, injection velocity, and proppant size. Results demonstrate the particulate transport is highly influenced by the ratio of proppant diameter to mean fracture aperture, and quantified in terms of areal space that proppant coverage occurs.

Rousta, Farid↗

Computational Modeling of Hydraulic Properties of a Sheared Single Rock Fracture

Flow through a single mechanically sheared Marcellus shale fracture was investigated computationally and experimentally. To provide a better understanding of the variation of hydraulic and geometrical characteristics of a fracture subjected to shearing, coupled shear flow tests on the fracture for four shearing displacement steps under constant normal stress were performed. At the end of each shearing step, computed tomography (CT) scans with resolution 26.8 μm were obtained and the corresponding fracture geometries were evaluated. The CT images were used to generate full aperture maps of the fracture configuration. In addition, average aperture maps were also created by averaging the full-resolution data over 10 × 10 pixels, smoothing out fine structural details. Computational modeling of water flow through the fractures at different shearing steps was performed using a modified local cubic law approach and the 3D full Navier–Stokes equations with the use of the ANSYS-Fluent software. Both the average aperture maps and full maps were used in these simulations. The experimental pressure drops of the fracture at shearing step 1, which has very small apertures, poorly matched the numerical results, quite likely because the fracture structure was inadequately captured by the scanning resolution. Shearing typically increased the aperture height of the fracture, whose features were then better captured by the CT scan. Good agreement between the experimental data and the numerical results of the full map for shearing step 2 was observed. The simulations were performed for both full and average aperture maps, and the effects of scan resolution and surface roughness on the accuracy of the results were studied. The modified local cubic law and full Navier–Stokes simulations of the averaged map fracture were found to be in good agreement. It was conjectured that this was because the nonlinear losses were insignificant for the smoothed out averaged map fracture. Similar comparisons with those of the full map showed agreement in trends, but there were some quantitative differences. The averaged fracture map simulations also predicted lower pressure drops compared to the full map, particularly for high flow rates. These differences were due to the fine-scale geometrical complexity (surface roughness) of fracture geometry that affects the fluid flow in the fracture. In conclusion, an improved cubic law model was also proposed, and its accuracy was verified by comparing its predictions with those of the Navier–Stokes simulations.

58 GEOSCIENCES↗

Foamed Cement Generation Methods: Insights from Macro-Porosity and Void Distribution

The American Petroleum Institute (API) Recommended Practice 10B-4 is the industry standard for measuring foamed cement stability, however, it does not incorporate the effects of elevated pressure or placement. Using high resolution computed tomography (CT) scanning, this study examines how cement slurry flow through pipes impacts void distribution in cured foamed cement. Analysis of the void size and distribution allows a comparison of lab and field generation; simulated velocity profiles indicate cement flow through constrictions likely 4 influences structural variations. Notably, field generated samples show more nitrogen bubbles at the injection port. Moreover, a review of the average bubble diameter concludes lab samples have average bubble sizes that increase with their quality, while field samples have similar average bubble diameters suggesting variation among generation methods.

36 MATERIALS SCIENCE↗

Electrostatic force distribution on an electrodynamic screen

The enormous potential of solar energy harvesting plants to provide clean energy is severely limited by dust accumulation on their optical surfaces. In lieu of the most commonly-practiced manual cleaning method of using high-pressure water jets, electrodynamic screen (EDS) technology offers an attractive solution for removing dust particles from optical surfaces using electrostatic forces. In this paper, the impacts of different EDS design parameters in the electric field distribution on an EDS have been studied. Furthermore, based on electric field expressions, closed-form solutions for multipolar dielectrophoretic (DEP) forces in the EDS application are provided. Detailed evaluation of the EDS performance necessi- tates investigation of different forces involved in the dust removal process. Different comparisons are made between repelling and attracting forces exerted on dust particles deposited on an EDS surface. These comparisons elucidate EDS performance in the removal of a given size range of dust particles. The significant detrimental impact of relative humidity upon the dust removal process is quantitatively addressed. As a result, it is shown how just a 10 percent increase in relative humidity can make the repelling force ineffective in the dust removal process.

14 SOLAR ENERGY↗

Computational Modeling of Fluid Flow through a Fracture in Permeable Rock

Laminar, single-phase, finite-volume solutions to the Navier–Stokes equations of fluid flow through a fracture within permeable media have been obtained. The fracture geometry was acquired from computed tomography scans of a fracture in Berea sandstone, capturing the small-scale roughness of these natural fluid conduits. First, the roughness of the two-dimensional fracture profiles was analyzed and shown to be similar to Brownian fractal structures. The permeability and tortuosity of each fracture profile was determined from simulations of fluid flow through these geometries with impermeable fracture walls. A surrounding permeable medium, assumed to obey Darcy’s Law with permeabilities from 0.2 to 2,000 millidarcies, was then included in the analysis. A series of simulations for flows in fractured permeable rocks was performed, and the results were used to develop a relationship between the flow rate and pressure loss for fractures in porous rocks. The resulting frictionfactor, which accounts for the fracture geometric properties, is similar to the cubic law; it has the potential to be of use in discrete fracture reservoir-scale simulations of fluid flow through highly fractured geologic formations with appreciable matrix permeability. The observed fluid flow from the surrounding permeable medium to the fracture was significant when the resistance within the fracture and the medium were of the same order. An increase in the volumetric flow rate within the fracture profile increased by more than 5% was observed for flows within high permeability-fractured porous media.

58 GEOSCIENCES↗

Measurement of Interfacial Area Production and Permeability within Porous Media

An understanding of the pore-level interactions that affect multi-phase flow in porous media is important in many subsurface engineering applications, including enhanced oil recovery, remediation of dense non-aqueous liquid contaminated sites, and geologic CO2 sequestration. Standard models of two-phase flow in porous media have been shown to have several shortcomings, which might partially be overcome using a recently developed model based on thermodynamic principles that includes interfacial area as an additional parameter. A few static experimental studies have been previously performed, which allowed the determination of static parameters of the model, but no information exists concerning the interfacial area dynamic parameters. A new experimental porous flow cell that was constructed using stereolithography for two-phase gas-liquid flow studies was used in conjunction with an in-house analysis code to provide information on dynamic evolution of both fluid phases and gas-liquid interfaces. In this paper, we give a brief introduction to the new generalized model of two-phase flow model and describe how the stereolithography flow cell experimental setup was used to obtain the dynamic parameters for the interfacial area numerical model. In particular, the methods used to determine the interfacial area permeability and production terms are shown.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Direct, Dynamic Measurement of Interfacial Area within Porous Media

Standard models of two-phase flow in porous media have been shown to exhibit several shortcomings that might be partially overcome with a recently developed model based on thermodynamic principles (Hassanizadeh and Gray, 1990). This alternative two-phase flow model contains a set of new and non-standard parameters, including specific interfacial area. By incorporating interfacial area production, destruction, and propagation into functional relationships that describe the capillary pressure and saturation, a more physical model has been developed. Niessner and Hassanizadeh (2008) have examined this model numerically and have shown that the model captures saturation hysteresis with drainage/imbibition cycles. Several static experimental studies have been performed to examine the validity of this new thermodynamically based approach; these allow the determination of static parameters of the model. To date, no experimental studies have obtained information about the dynamic parameters required for the model. A new experimental porous flow cell has been constructed using stereolithography to study two-phase flow phenomena (Crandall et al. 2008). A novel image analysis tool was developed for an examination of the evolution of flow patterns during displacement experiments (Crandall et al. 2009). This analysis tool enables the direct quantification of interfacial area between fluids by matching known geometrical properties of the constructed flow cell with locations identified as interfaces from images of flowing fluids. Numerous images were obtained from two-phase experiments within the flow cell. The dynamic evolution of the fluid distribution and the fluid-fluid interface locations were determined by analyzing these images. In this paper, we give a brief introduction to the thermodynamically based two-phase flow model, review the properties of the stereolithography flow cell, and show how the image analysis procedure has been used to obtain dynamic parameters for the numerical model. These parameters include production/destruction of interfacial area as a function of saturation and capillary pressure. Our preliminary results for primary drainage in porous media show that the specific interfacial area increased linearly with increasing gas saturation until breakthrough of the displacing gas into the exit manifold occurred.

54 ENVIRONMENTAL SCIENCES↗

Two-Phase Flow Simulations In a Natural Rock Fracture using the VOF Method

Standard models of two-phase flow in porous media have been shown to exhibit several shortcomings that might be partially overcome with a recently developed model based on thermodynamic principles (Hassanizadeh and Gray, 1990). This alternative two-phase flow model contains a set of new and non-standard parameters, including specific interfacial area. By incorporating interfacial area production, destruction, and propagation into functional relationships that describe the capillary pressure and saturation, a more physical model has been developed. Niessner and Hassanizadeh (2008) have examined this model numerically and have shown that the model captures saturation hysteresis with drainage/imbibition cycles. Several static experimental studies have been performed to examine the validity of this new thermodynamically based approach; these allow the determination of static parameters of the model. To date, no experimental studies have obtained information about the dynamic parameters required for the model. A new experimental porous flow cell has been constructed using stereolithography to study two-phase flow phenomena (Crandall et al. 2008). A novel image analysis tool was developed for an examination of the evolution of flow patterns during displacement experiments (Crandall et al. 2009). This analysis tool enables the direct quantification of interfacial area between fluids by matching known geometrical properties of the constructed flow cell with locations identified as interfaces from images of flowing fluids. Numerous images were obtained from two-phase experiments within the flow cell. The dynamic evolution of the fluid distribution and the fluid-fluid interface locations were determined by analyzing these images. In this paper, we give a brief introduction to the thermodynamically based two-phase flow model, review the properties of the stereolithography flow cell, and show how the image analysis procedure has been used to obtain dynamic parameters for the numerical model. These parameters include production/destruction of interfacial area as a function of saturation and capillary pressure. Our preliminary results for primary drainage in porous media show that the specific interfacial area increased linearly with increasing gas saturation until breakthrough of the displacing gas into the exit manifold occurred.

54 ENVIRONMENTAL SCIENCES↗