Engineering topics

Adelfang, S. I.

Publications and source records attributed to Adelfang, S. I..

At least 19 records

NASA NTRS2008

Simulation of Ground Winds Time Series

A simulation process has been developed for generation of the longitudinal and lateral components of ground wind atmospheric turbulence as a function of mean wind speed, elevation, temporal frequency range and distance between locations. The distance between locations influences the spectral coherence between the simulated series at adjacent locations. Short distances reduce correlation only at high frequencies; as distances increase correlation is reduced over a wider range of frequencies. The choice of values for the constants d1 and d3 in the PSD model is the subject of work in progress. An improved knowledge of the values for zO as a function of wind direction at the ARES-1 launch pads is necessary for definition of d1. Results of other studies at other locations may be helpful as summarized in Fichtl's recent correspondence. Ideally, further research is needed based on measurements of ground wind turbulence with high resolution anemometers at a number of altitudes at a new KSC tower located closer to the ARES-1 launch pad .The proposed research would be based on turbulence measurements that may be influenced by surface terrain roughness that may be significantly different from roughness prior to 1970 in Fichtl's measurements. Significant improvements in instrumentation, data storage end processing will greatly enhance the capability to model ground wind profiles and ground wind turbulence.

Adelfang, S. I.↗

NASA NTRS2004

Simulation of Wind Profile Perturbations for Launch Vehicle Design

Ideally, a statistically representative sample of measured high-resolution wind profiles with wavelengths as small as tens of meters is required in design studies to establish aerodynamic load indicator dispersions and vehicle control system capability. At most potential launch sites, high- resolution wind profiles may not exist. Representative samples of Rawinsonde wind profiles to altitudes of 30 km are more likely to be available from the extensive network of measurement sites established for routine sampling in support of weather observing and forecasting activity. Such a sample, large enough to be statistically representative of relatively large wavelength perturbations, would be inadequate for launch vehicle design assessments because the Rawinsonde system accurately measures wind perturbations with wavelengths no smaller than 2000 m (1000 m altitude increment). The Kennedy Space Center (KSC) Jimsphere wind profiles (150/month and seasonal 2 and 3.5-hr pairs) are the only adequate samples of high resolution profiles approx. 150 to 300 m effective resolution, but over-sampled at 25 m intervals) that have been used extensively for launch vehicle design assessments. Therefore, a simulation process has been developed for enhancement of measured low-resolution Rawinsonde profiles that would be applicable in preliminary launch vehicle design studies at launch sites other than KSC.

Adelfang, S. I.↗

NASA NTRS2003

Analysis of Near Simultaneous Jimsphere and AMPS High Resolution Wind Profiles

The high-resolution wind profile of the Automated Meteorological Profiling System (HRAMPS) is the proposed replacement for the Jimsphere measurement system used to support NASA Shuttle launches from the Eastern Test Range (ETR). Samples of twenty-six ETR near simultaneous Jimsphere and HRAMPS wind profiles were obtained for Shuttle program HRAMPS certification studies. Shuttle systems engineering certification is to ensure that spacecraft and launch vehicle systems performance and safety evaluations for each launch (derived from flight simulations with Jimsphere wind profile data bases) retain their validity when HRAMPS profiles are used on day-of-launch (DOL) in trajectory and loads simulations to support the commit-to-launch decision. This paper describes a statistical analysis of the near simultaneous profiles. In principle the differences between a Jimsphere profile and an HRAMPS profile should be attributed to tracking technology (radar versus GPS tracking of a Jimsphere flight element) and the method for derivation of wind vectors from the raw tracking data. In reality, it is not technically feasible to track the same Jimsphere balloon with the two systems. The aluminized Mylar surface of the standard Jimsphere flight element facilitates radar tracking, but it interferes with HRAMPS during simultaneous tracking. Suspending a radar reflector from an HRAMPS flight element (Jimsphere without aluminized coating) does not produce satisfactory Jimsphere profiles because of intermittent radar returns. Thus, differences between the Jimsphere and HRAMPS profiles are also attributed to differences in the trajectories of separate flight elements. Because of small sample size and a test period limited to one winter season, test measurements during extreme high winds aloft could not have been expected and did not occur. It is during the highest winds that the largest differences between Jimsphere and HRAMPS would occur because the distance between flight elements would be larger. Jimsphere radar tracking noise increases as a function of balloon displacement downrange. The Jimsphere data processing compensates for tracking signal/noise degradation by increasing the smoothing interval. The Jimsphere wind profile effective resolution is a function of downrange distance and altitude, whereas the effective resolution of the HRAMPS should be independent of those variables. The procedure used for editing Jimsphere spikes in Shuttle DOL profiles was not implemented for the Jimsphere profile measurements during the AMPS field tests. For this analysis a code was developed that essentially mimics DOL Jimsphere spike editing. Jimsphere profiles have somewhat more noise in the wavelength range less than 200m defined as the noise floor. No differences between Jimsphere and HRAMPS wind profile pairs have been found that would support denial of HRAMPS certification for application in Shuttle DOL applications. The reliability of the HRAMPS system, which is an important certification issue, is not addressed in this study.

Adelfang, S. I.↗

NASA NTRS2003

Simulation of Wind Profile Perturbations for Launch Vehicle Ascent Flight Systems Design Assessments

Ideally, a statistically representative sample of measured high-resolution wind profiles with wavelengths as small as tens of meters is required for assessment of launch vehicle ascent flight systems component capability and vehicle operability for a selected launch site. At most potential launch sites a sample of high-resolution measured wind profiles may not exist. Representative samples of Rawinsonde wind profiles are more likely to be available because of the extensive network of measurement sites established for routine measurements at 12-hr intervals in support of national and international weather observing and forecasting activity. Such a sample, although large enough to statistically represent relatively large wavelength perturbations, would be inadequate for launch system design assessment applications because the Rawinsonde system can accurately measure wind perturbations with wavelengths no smaller than 2000m (1000m altitude increment). Wavelengths less than 2000m in the raw Rawinsonde data, which tend to be dominated by un-damped spurious balloon motion and radar tracking system noise, are filtered within the data processing scheme. The Kennedy Space Center (KSC) Jimsphere wind profiles (150/month and seasonal pairs) are the only adequate high resolution (approximately 150 to 300m effective resolution, but over-sampled at 25m intervals) data that have been used extensively in launch vehicle design, operability assessments and operational protection of vehicle systems for wind perturbation uncertainty. Jimsphere wind profiles have been measured at a few other potential launch sites but the number of profiles is relatively small and the samples are not statistically representative of the site dependent wind profile variability. A simulation process has been developed for enhancement of measured low-resolution Rawinsonde profiles that are more likely to be available in the vicinity of potential launch sites and are a statistically representative sample of wind profile perturbation wavelengths greater than 2000m. The enhancement produces perturbed wind profiles with wavelengths as small as desired for application in launch vehicle ascent flight simulations and design assessments.

Adelfang, S. I.↗

NASA NTRS1999

User's Guide for Monthly Vector Wind Profile Model

The background, theoretical concepts, and methodology for construction of vector wind profiles based on a statistical model are presented. The derived monthly vector wind profiles are to be applied by the launch vehicle design community for establishing realistic estimates of critical vehicle design parameter dispersions related to wind profile dispersions. During initial studies a number of months are used to establish the model profiles that produce the largest monthly dispersions of ascent vehicle aerodynamic load indicators. The largest monthly dispersions for wind, which occur during the winter high-wind months, are used for establishing the design reference dispersions for the aerodynamic load indicators. This document includes a description of the computational process for the vector wind model including specification of input data, parameter settings, and output data formats. Sample output data listings are provided to aid the user in the verification of test output.

Adelfang, S. I.↗

NASA NTRS1998

A Compendium of Wind Statistics and Models for the NASA Space Shuttle and Other Aerospace Vehicle Programs

The wind profile with all of its variations with respect to altitude has been, is now, and will continue to be important for aerospace vehicle design and operations. Wind profile databases and models are used for the vehicle ascent flight design for structural wind loading, flight control systems, performance analysis, and launch operations. This report presents the evolution of wind statistics and wind models from the empirical scalar wind profile model established for the Saturn Program through the development of the vector wind profile model used for the Space Shuttle design to the variations of this wind modeling concept for the X-33 program. Because wind is a vector quantity, the vector wind models use the rigorous mathematical probability properties of the multivariate normal probability distribution. When the vehicle ascent steering commands (ascent guidance) are wind biased to the wind profile measured on the day-of-launch, ascent structural wind loads are reduced and launch probability is increased. This wind load alleviation technique is recommended in the initial phase of vehicle development. The vehicle must fly through the largest load allowable versus altitude to achieve its mission. The Gumbel extreme value probability distribution is used to obtain the probability of exceeding (or not exceeding) the load allowable. The time conditional probability function is derived from the Gumbel bivariate extreme value distribution. This time conditional function is used for calculation of wind loads persistence increments using 3.5-hour Jimsphere wind pairs. These increments are used to protect the commit-to-launch decision. Other topics presented include the Shuttle Shuttle load-response to smoothed wind profiles, a new gust model, and advancements in wind profile measuring systems. From the lessons learned and knowledge gained from past vehicle programs, the development of future launch vehicles can be accelerated. However, new vehicle programs by their very nature will require specialized support for new databases and analyses for wind, atmospheric parameters (pressure, temperature, and density versus altitude), and weather. It is for this reason that project managers are encouraged to collaborate with natural environment specialists early in the conceptual design phase. Such action will give the lead time necessary to meet the natural environment design and operational requirements, and thus, reduce development costs.

Smith, O. E.↗

NASA NTRS1997

Neutral Orbital Altitude Density Effects on the International Space Station

One of the design requirements of the International Space Station (ISS) is that each year accelerations of one micro-g cannot be exceeded at the ISS internal payload location for 6 periods of not less than 30 consecutive days. Although there are other causes, this study deals only with the accelerations caused by atmospheric drag. The critical ambient neutral density, computed using the Marshall Engineering Thermosphere Model, required to produce accelerations of one micro-g on the ISS, is estimated using an atmospheric drag acceleration equation. Results show that the design requirements may be difficult to meet during periods of extremely high solar activity; the planned reboost and altitude strategies for the ISS may have to be revised to allow for the uncertainty in the prediction of neutral atmospheric density within the 100-day period established for orbital decay before reboost.

Smith, O.E.↗

NASA NTRS1996

Ambient mass density effects on the International Space Station (ISS) microgravity experiments

The Marshall engineering thermosphere model was specified by NASA to be used in the design, development and testing phases of the International Space Station (ISS). The mass density is the atmospheric parameter which most affects the ISS. Under simplifying assumptions, the critical ambient neutral density required to produce one micro-g on the ISS is estimated using an atmospheric drag acceleration equation. Examples are presented for the critical density versus altitude, and for the critical density that is exceeded at least once a month and once per orbit during periods of low and high solar activity. An analysis of the ISS orbital decay is presented.

Smith, O. E.↗

NASA NTRS1993

A wind model for launch vehicle design

A new vector wind profile model is described based on the properties of the quadrivariate normal distribution which will help establish preliminary design ranges for angle of attack, angle of sideslip, aerodynamic pressure, and other launch vehicle flight variables. The model produces wind profiles that are a reasonable substitute for measured wind profile samples. The model wind profiles produce dispersion in aerodynamic load indicators that cover the dispersion range calculated from an extensive sample of Jimsphere wind profiles. This is accomplished with only 12 model wind profiles compared to 1800 Jimsphere profiles for a selected reference altitude. This represents an opportunity for a considerable reduction of computational effort during design phases that require many iterations to establish the merit of various design philosophies.

Adelfang, S. I.↗

NASA NTRS1991

Wind profile perturbation analysis for STS

Two case studies of the relationship between STS ascent structural loads and wind profile characteristics are described. In the first case study, a wind profile with relatively weak winds is used to demonstrate the importance of launch vehicle velocity relative to the air and its effect on loads. In the second study, a pair of wind profiles is used to show how the determination of load exceedances is strongly influenced by the wind load persistence allowances for the baseline and two day-of-launch (DOL) steering commands called I-LOADs. Characteristics of the wind profiles and associated trajectory variable and wind-sensitive load indicators are examined. Energy spectra of in-plane and out-of-plane wind component and a load indicator are presented. An analysis of load indicator sensitivity to wind perturbation energy in the 1600-6400 m wavelength band for baseline and DOL I-LOAD is described.

Adelfang, S. I.↗

NASA NTRS1990

Wind models for the NSTS ascent trajectory biasing for wind load alleviation

New concepts are presented for aerospace vehicle ascent wind profile biasing. The purpose for wind biasing the ascent trajectory is to provide ascent wind loads relief and thus decrease the probability for launch delays due to wind loads exceeding critical limits. Wind biasing trajectories to the the profile of monthly mean winds have been widely used for this purpose. The wind profile models presented give additional alternatives for wind biased trajectories. They are derived from the properties of the bivariate normal probability function using the available wind statistical parameters for the launch site. The analytical expressions are presented to permit generalizations. Specific examples are given to illustrate the procedures. The wind profile models can be used to establish the ascent trajectory steering commands to guide the vehicle through the first stage. For the National Space Transportation System (NSTS) program these steering commands are called I-loads.

Smith, O. E.↗

NASA NTRS1989

Wind models for the NSTS ascent trajectory biasing for wind load alleviation

New concepts are presented for aerospace vehicle ascent wind profile biasing. The purpose for wind biasing the ascent trajectory is to provide ascent wind loads relief and thus decrease the probability for launch delays due to wind loads exceeding critical limits. Wind biasing trajectories to the profile of monthly mean winds have been widely used for this purpose. The wind profile models presented give additional alternatives for wind biased trajectories. They are derived from the properties of the bivariate normal probability function using the available wind statistical parameters for the launch site. The analytical expressions are presented to permit generalizations. Specific examples are given to illustrate the procedures. The wind profile models can be used to establish the ascent trajectory steering commands to guide the vehicle through the first stage. For the National Space Transportation System (NSTS) program these steering commands are called I-loads.

Smith, O. E.↗

NASA NTRS1988

Ascent structural wind loads for the National Space Transportation System (NSTS)

An aerospace vehicle must withstand the design ascent structural load or be within any flight constraint to safely reach orbit. For the NSTS an assessment for flight readiness is made for each mission. This assessment for ascent loads and performance parameters is stated in terms of launch probability derived from samples of Jimsphere wind profiles. For the day of launch operations an allowance is made for the ascent load variability due to the wind profile variability over a 3.5-hour period. This is the current time period required to obtain a Jimsphere measurement and perform a complete load simulation prior to launch time. The load variability is derived from a sample of 3.5-hour Jimsphere wind profile pairs. It is applied as a conditional percentile value given the wind load at 3.5 hours prior to launch time. Probability models are used for these analyses. Application of the univariate, bivariate and conditional forms of the extreme value (Gumbel) probability distribution to the analysis of extreme wind speeds, wind shears and vehicle loads is described.

Smith, O. E.↗

NASA NTRS1988

Winds aloft statistical analysis in support of day of launch Shuttle systems evaluation

In connection with the development of the Meteorological Interactive Data Display System (MIDDS) for utilization by the Launch Systems Evaluation Advisory Team (LSEAT), requirements have been established to expand the pre-launch analysis of winds aloft for the Space Shuttle. Statistical analyses developed for the system include: comparison of pre-launch wind component profiles to wind component extremes at each altitude calculated from launch site historical data; conditional probability ellipses for wind vectors at a future time given the wind vector at an initial time; comparison of observed extreme wind shear and associated wind speed with launch site historical data utilizing the bivariate extreme value (Gumbel) distribution; estimation of extremes of wind speed or wind shear at a future time given the extremes of either variable at an initial time, utilizing the conditional extreme value distribution; power spectrum analysis for tracking wind perturbation energy in sequential pre-launch Jimsphere wind profiles.

Adelfang, S. I.↗

NASA NTRS1987

Study of wind change for the development of loads reduction techniques for the space shuttle

Wind change statistics are analyzed for Vandenberg AFB, California (VAFB) and Kennedy Space Center, Florida (KSC). Means and standard deviations of wind component change and vector wind change modulus within 3-9 and 9-16 km altitude bands are tabulated. The contribution to 3.5 hr wind component change by wind perturbations in various wavelength bands is evaluated. Probability distributions of maximum 3.5 hr wind change in an altitude band are presented and a model for wind change at a specified altitude is tested with data derived from six data bases from VAFB and Santa Monica, California.

Adelfang, S. I.↗

NASA NTRS1984

Vector wind gust model

The development of a vector wind gust model through statistical analysis is described. Wind perturbation statistics which include location, altitude, season, and wavelength range are used in the synthesis of detailed wing profiles. These profiles provide the basis for the establishment of improved discrete gust design criteria guidelines for ascending launch vehicles.

Adelfang, S. I.↗

NASA NTRS1983

Vector wind profile gust model

A five parameter gamma distribution (BGD) having two shape parameters, two location parameters, and a correlation parameter is investigated. This general BGD is expressed as a double series and as a single series of the modified bessel function, and reduces to the known special case for equal shape parameters. Practical functions for computer evaluations for the general BGD and for special cases are presented. Applications are to be bound in reliability theory, signal noise, and meteorology. Applications to wind gust modeling for the ascent flight of the space shuttle are illustrated.

Adelfang, S. I.↗

NASA NTRS1983

Information retrieval from wide-band meteorological data - An example

The methods proposed by Smith and Adelfang (1981) and Smith et al. (1982) are used to calculate probabilities over rectangles and sectors of the gust magnitude-gust length plane; probabilities over the same regions are also calculated from the observed distributions and a comparison is also presented to demonstrate the accuracy of the statistical model. These and other statistical results are calculated from samples of Jimsphere wind profiles at Cape Canaveral. The results are presented for a variety of wavelength bands, altitudes, and seasons. It is shown that wind perturbations observed in Jimsphere wind profiles in various wavelength bands can be analyzed by using digital filters. The relationship between gust magnitude and gust length is modeled with the bivariate gamma distribution. It is pointed out that application of the model to calculate probabilities over specific areas of the gust magnitude-gust length plane can be useful in aerospace design.

Adelfang, S. I.↗