Engineering Papers⌕ Search

Engineering topics

Addy, Harold E., Jr.

Publications and source records attributed to Addy, Harold E., Jr..

31 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Modern Airfoil Ice Accretions

This report presents results from the first icing tests performed in the Modem Airfoils program. Two airfoils have been subjected to icing tests in the NASA Lewis Icing Research Tunnel (IRT). Both airfoils were two dimensional airfoils; one was representative of a commercial transport airfoil while the other was representative of a business jet airfoil. The icing test conditions were selected from the FAR Appendix C envelopes. Effects on aerodynamic performance are presented including the effects of varying amounts of glaze ice as well as the effects of approximately the same amounts of glaze, mixed, and rime ice. Actual ice shapes obtained in these tests are also presented for these cases. In addition, comparisons are shown between ice shapes from the tests and ice shapes predicted by the computer code, LEWICE for similar conditions. Significant results from the tests are that relatively small amounts of ice can have nearly as much effect on airfoil lift coefficient as much greater amounts of ice and that glaze ice usually has a more detrimental effect than either rime or mixed ice. LEWICE predictions of ice shapes, in general, compared reasonably well with ice shapes obtained in the IRT, although differences in details of the ice shapes were observed.

Addy, Harold E., Jr.↗
NASA NTRS1995

Wave Journal Bearing. Part 2: Experimental Pressure Measurements and Fractional Frequency Whirl Threshold for Wave and Plain Journal Bearings

A new hydrodynamic bearing concept, the wave journal bearing, is being developed because it has better stability characteristics than plain journal bearings while maintaining similar load capacity. An analysis code to predict the steady state and dynamic performance of the wave journal bearing is also part of the development. To verify numerical predictions and contrast the wave journal bearing's stability characteristics to a plain journal bearing, tests were conducted at NASA Lewis Research Center using an air bearing test rig. Bearing film pressures were measured at 16 ports located around the bearing circumference at the middle of the bearing length. The pressure measurements for both a plain journal bearing and a wave journal bearing compared favorably with numerical predictions. Both bearings were tested with no radial load to determine the speed threshold for self-excited fractional frequency whirl. The plain journal bearing started to whirl immediately upon shaft start-up. The wave journal did not incur self-excited whirl until 800 to 900 rpm as predicted by the analysis. Furthermore, the wave bearing's geometry limited the whirl orbit to less than the bearing's clearance. In contrast, the plain journal bearing did not limit the whirl orbit, causing it to rub.

Walker, James F.↗
NASA NTRS1994

High temperature seal test rig

The High Temperature Seals Test Rig Program at NASA's Lewis Research Center is a joint effort involving three separate federal government agencies. Testing has been underway at Lewis in this test rig since April, 1993. The rig was designed to run tests at temperatures to 800 F at pressures to 200 psia or at temperatures to 1300 to 1500 F at pressures to 65 psia. It was designed to run at speeds of up to 50,000 rpm which, for a 5.1 inch diameter disk, is a surface speed of about 1100 ft./sec. The rig was designed to allow easy replacement of the disks as well as the seals such that different disk materials and coatings may be tested.

Addy, Harold E., Jr.↗
NASA NTRS1994

Pressure measurements of a three wave journal air bearing

In order to validate theoretical predictions of a wave journal bearing concept, a bench test rig was assembled at NASA Lewis Research Center to measure the steady-state performance of a journal air bearing. The tester can run up to 30,000 RPM and the spindle has a run out of less than 1 micron. A three wave journal bearing (50 mm diameter and 58 mm length) has been machined at NASA Lewis. The pressures at 16 ports along the bearing circumference at the middle of the bearing length were measured and compared to the theoretical prediction. The bearing ran at speeds up to 15,000 RPM and certain loads. Good agreement was found between the measured and calculated pressures.

Dimofte, Florin↗
NASA NTRS1994

Aerodynamic Effects Of Deicing And Anti-Icing Fluids

Report presents results of wind-tunnel tests of aerodynamic effects of deicing and anti-icing fluids on airplane wings. Tests conducted on three-dimensional half-model airplane and two-dimensional airfoil model at temperatures ranging from -29 to +10 degrees C. Fluids used included three commercial fluids available for use during 1987-1988 winter season, one discontinued commercial fluid, and eight newer fluids experimental at time of test.

Addy, Harold E., Jr.↗
NASA NTRS1993

Lubrication of an 85-mm ball bearing with RP-1

A parametric experimental investigation of an 85 millimeter bore angular contact ball bearing running in RP-1 fuel was performed at speeds of 10000 to 24000 RPM. Thrust loads were varied from 4450 to 17800 Newtons (1000 to 4000 lbs.). Radial loads were varied from 1335 to 13350 Newtons (300 to 3000 lbs.). RP-1 lubrication for the bearing was provided through a stationary jet ring located adjacent to the test bearing outer ring. Increases in both the thrust and radial loads resulted in increased bearing temperature, while increases in shaft speed resulted in much more dramatic increases in bearing temperature. These trends are typical for ball bearings operating under these types of conditions. Results are given for outer ring temperatures of the test bearing at the various test conditions employed. In addition, the heat energy removed from the bearing by the RP-1 was determined by measuring the increase in temperature as the RP-1 passed through the bearing. Results showed that the amount of heat energy removed by the RP-1 increased with both shaft speed and RP-1 flow rate to the bearing.

Addy, Harold E., Jr.↗
NASA NTRS1993

Lubrication of an 85-mm ball bearing with RP-1

A parametric experimental investigation of an 85 millimeter bore angular contact ball bearing running in RP-1 fuel was performed at speeds of 10,000 to 24,000 rpm. Thrust loads were varied from 4450 to 17,800 Newtons (1000 to 4000 lbs.). Radial loads were varied from 1335 to 13,350 Newtons (300 to 3000 lbs.). RP-1 lubrication for the bearing was provided through a stationary jet ring located adjacent to the test bearing outer ring. Increases in both the thrust and radial loads resulted in increased bearing temperature, while increases in shaft speed resulted in much more dramatic increases in bearing temperature. These trends are typical for ball bearings operating under these types of conditions. Results are given for outer ring temperatures of the test bearing at the various test conditions employed. In addition, the heat energy removed from the bearing by the RP-1 was determined by measuring the increase in temperature as the RP-1 passed through the bearing. Results showed that the amount of heat energy removed by the RP-1 increased with both shaft speed and RP-1 flow rate to the bearing.

Addy, Harold E., Jr.↗
NASA NTRS1992

Lewis icing research tunnel test of the aerodynamic effects of aircraft ground deicing/anti-icing fluids

A wind tunnel investigation of the effect of aircraft ground deicing/anti-icing fluids on the aerodynamic characteristics of a Boeing 737-200ADV airplane was conducted. The test was carried out in the NASA Lewis Icing Research Tunnel. Fluids tested include a Newtonian deicing fluid, three non-Newtonian anti-icing fluids commercially available during or before 1988, and eight new experimental non-Newtonian fluids developed by four fluid manufacturers. The results show that fluids remain on the wind after liftoff and cause a measurable lift loss and drag increase. These effects are dependent on the high-lift configuration and on the temperature. For a configuration with a high-lift leading-edge device, the fluid effect is largest at the maximum lift condition. The fluid aerodynamic effects are related to the magnitude of the fluid surface roughness, particularly in the first 30 percent chord. The experimental fluids show a significant reduction in aerodynamic effects.

Runyan, L. James↗
NASA NTRS1990

A numerical simulation of the flow in the diffuser of the NASA Lewis icing research tunnel

The flow in the diffuser section of the Icing Research Tunnel at the NASA Lewis Research Center is numerically investigated. To accomplish this, an existing computer code is utilized. The code, known as PARC3D, is based on the Beam-Warming algorithm applied to the strong conservation law form of the complete Navier-Stokes equations. The first portion of the paper consists of a brief description of the diffuser and its current flow characteristics. A brief discussion of the code work follows. Predicted velocity patterns are then compared with the measured values.

Addy, Harold E., Jr.↗
NASA NTRS1990

A numerical simulation of the flow in the diffuser of the NASA Lewis Icing Research Tunnel

The flow in the diffuser section of the Icing Research Tunnel at the NASA Lewis Research Center is numerically investigated. To accomplish this, an existing computer code is utilized. The code, known as PARC3D, is based on the Beam-Warming algorithm applied to the strong conservation law form of the complete Navier-Stokes equations. The first portion of the paper consists of a brief description of the diffuser and its current flow characteristics. A brief discussion of the code work follows. Predicted velocity patterns are then compared with the measured values.

Addy, Harold E., Jr.↗
NASA NTRS1989

Investigation of the flow in the diffuser section of the NASA Lewis icing research tunnel

The flow in the diffuser section of the Icing Research Wind Tunnel at NASA Lewis Research Center is investigated using both tunnel calibration measurements and numerical simulation techniques. Local pressure and temperature measurements are made to establish velocity and temperature profiles in the diffuser of the tunnel. These profiles are compared with similar measurements made prior to renovating the equipment which generates the tunnel's icing cloud. This comparison indicates the manner in which this change affected the flow. The measured data were also compared with a numerical simulation of the flow to help understand how such changes may favorably alter the tunnel flow.

Addy, Harold E., Jr.↗
NASA NTRS1989

Investigation of the flow in the diffuser section of the NASA Lewis Icing Research Tunnel

The flow in the diffuser section of the Icing Research Wind Tunnel at NASA Lewis Research Center is investigated using both tunnel calibration measurements and numerical simulation techniques. Local pressure and temperature measurements are made to establish velocity and temperature profiles in the diffuser of the tunnel. These profiles are compared with similar measurements made prior to renovating the equipment which generates the tunnel's icing cloud. This comparison indicates the manner in which this change affected the flow. The measured data were also compared with a numerical simulation of the flow to help understand how such changes may favorably alter the tunnel flow.

Addy, Harold E., Jr.↗