Engineering Papers⌕ Search

Engineering topics

Adams, David P.

Publications and source records attributed to Adams, David P..

At least 91 records · Page 5

Ignition and self-propagating reactions in Al/Pt multilayers of varied design

The different rate-limiting processes underlying ignition and self-propagating reactions in Al/Pt multilayers are examined through experiments and analytical modeling. Freestanding, ~1.6 μm-thick Al/Pt multilayers of varied stoichiometries and nanometer-scale layer thicknesses ignite at temperatures below the melting point of both reactants (and eutectics) demonstrating that initiation occurs via solid-state mixing. Equimolar multilayers exhibit the lowest ignition temperatures when comparing structures having a specific bilayer thickness. An activation energy of 76.6 kJ/mol at. associated with solid state mass transport is determined from the model analysis of ignition. High speed videography shows that equimolar Al/Pt multilayers undergo the most rapid self-sustained reactions with wavefront speeds as large as 73 m/s. Al- and Pt-rich multilayers react at reduced rates (as low as 0.3 m/s), consistent with reduced heat of reaction and lower adiabatic temperatures. An analytical model that accounts for key thermodynamic properties, preliminary mixing along interfaces, thermal transport, and mass diffusion is used to predict the wavefront speed dependencies on bilayer thickness. Finally, good fits to experimental data provide estimates for activation energy (51 kJ/mol at.) associated with mass transport subject to high heating rates and thermal diffusion coefficient of premixed interfacial volumes (2.8 × 10 -6 m 2 /s). Pt dissolution into molten Al is identified as a rate-limiting step underlying high temperature propagating reactions in Al/Pt multilayers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Achieving Ultralow Wear with Stable Nanocrystalline Metals

Recent work suggests that thermally stable nanocrystallinity in metals is achievable in several binary alloys by modifying grain boundary energies via solute segregation. The remarkable thermal stability of these alloys has been demonstrated in recent reports, with many alloys exhibiting negligible grain growth during prolonged exposure to near-melting temperatures. In this paper, we show that PtAu, a proposed stable alloy consisting of two noble metals, exhibits extraordinary resistance to wear. Ultra-low wear rates, less than a monolayer of material removed per sliding pass, were measured for PtAu thin films at a maximum Hertz contact stress of up to 1.1 GPa. This is the first instance of an all-metallic material exhibiting a specific wear rate on the order of 10 -9 mm 3 /N-m, comparable to diamond-like carbon and sapphire. Remarkably, the wear rate of sapphire and silicon nitride probes used in wear experiments were either higher or comparable to that of the PtAu alloy, despite the substantially higher hardness of the ceramic probe materials. High-resolution microscopy showed negligible surface microstructural evolution in the wear tracks after 100k sliding passes. Finally, mitigation of fatigue-driven delamination enabled a transition to wear by atomic attrition, a regime previously limited to highly wear resistant materials such as diamond-like carbon.

36 MATERIALS SCIENCE↗

Achieving Ultralow Wear with Stable Nanocrystalline Metals

Abstract Recent work suggests that thermally stable nanocrystallinity in metals is achievable in several binary alloys by modifying grain boundary energies via solute segregation. The remarkable thermal stability of these alloys has been demonstrated in recent reports, with many alloys exhibiting negligible grain growth during prolonged exposure to near‐melting temperatures. Pt–Au, a proposed stable alloy consisting of two noble metals, is shown to exhibit extraordinary resistance to wear. Ultralow wear rates, less than a monolayer of material removed per sliding pass, are measured for Pt–Au thin films at a maximum Hertz contact stress of up to 1.1 GPa. This is the first instance of an all‐metallic material exhibiting a specific wear rate on the order of 10 −9 mm 3 N −1 m −1 , comparable to diamond‐like carbon (DLC) and sapphire. Remarkably, the wear rate of sapphire and silicon nitride probes used in wear experiments are either higher or comparable to that of the Pt–Au alloy, despite the substantially higher hardness of the ceramic probe materials. High‐resolution microscopy shows negligible surface microstructural evolution in the wear tracks after 100k sliding passes. Mitigation of fatigue‐driven delamination enables a transition to wear by atomic attrition, a regime previously limited to highly wear‐resistant materials such as DLC.

Curry, John F.↗

Heating rate dependent ignition of Al/Pt nanolaminates through pulsed laser irradiation

Direct laser irradiation of sputter deposited Al/Pt nanolaminate multilayers results in rapid local heating and exothermic mixing of reactant layers. Milli- and microsecond pulsed laser irradiation under certain test conditions leads to single-point ignition of rapid, self-propagating, formation reactions. Multilayers having bilayer thicknesses of 328 nm, 164 nm, and 65 nm are characterized by their ignition onset times and temperatures. Smaller bilayer thickness multilayers require less laser intensity for ignition compared with larger bilayer designs (when utilizing a particular pulse duration). The relationship between laser intensity and ignition onset time is used to calibrate an activation energy for ignition within a finite element reactive heat transport model. The local heating rate is varied from 10 4 K/s to 10 6 K/s by selecting a laser intensity. Kissinger analysis was performed on the heating rate-dependent ignition temperatures measured with high speed pyrometry to experimentally determine an activation energy in the foils of (6.2 ± 1.6 × 10 4 J/mole atoms). Furthermore, this value is then compared to an activation energy produced from model fits to an ignition onset time of 7.2 × 10 4 J/mole atoms.

36 MATERIALS SCIENCE↗

Signatures of the unique microstructure of additively manufactured steel observed via diffraction

A series of measurements were designed to gain confidence in the interpretation of the peak breadth in diffraction patterns collected from additively manufactured material, which has a novel microstructure in comparison to the well understood microstructure of wrought materials. Stainless steels made with two additive manufacturing techniques were compared to wrought material. Similar patterns observed in the scattering vector dependence for additively manufactured and deformed wrought materials suggested that the broadening in both materials was related to dislocations. Finally, this was confirmed by heat-treatment, during which both materials exhibited recovery due to the annealing of dislocations at the same temperature.

304L stainless-steel↗

Lateral vias for connections to buried microconductors

The present invention relates to a lateral via to provide an electrical connection to a buried conductor. In one instance, the buried conductor is a through via that extends along a first dimension, and the lateral via extends along a second dimension that is generally orthogonal to the first dimension. In another instance, the second dimension is oblique to the first dimension. Components having such lateral vias, as well as methods for creating such lateral vias are described herein.

42 ENGINEERING↗