Engineering Papers⌕ Search

Engineering topics

Abernathy, Harry

Publications and source records attributed to Abernathy, Harry.

66 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Surface and Bulk Oxygen Kinetics of BaCo 0.4 Fe 0.4 Zr 0.2-X Y X O 3-δ Triple Conducting Electrode Materials

Triple ionic-electronic conductors have received much attention as electrode materials. In this work, the bulk characteristics of oxygen diffusion and surface exchange were determined for the triple-conducting BaCo 0.4 Fe 0.4 Zr 0.2-X Y X O 3-δ suite of samples. Y substitution increased the overall size of the lattice due to dopant ionic radius and the concomitant formation of oxygen vacancies. Oxygen permeation measurements exhibited a three-fold decrease in oxygen permeation flux with increasing Y substitution. The DC total conductivity exhibited a similar decrease with increasing Y substitution. These relatively small changes are coupled with an order of magnitude increase in surface exchange rates from Zr-doped to Y-doped samples as observed by conductivity relaxation experiments. The results indicate that Y-doping inhibits bulk O 2- conduction while improving the oxygen reduction surface reaction, suggesting better electrode performance for proton-conducting systems with greater Y substitution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

SOC Synthetic Microstructure Bank

QUICK START: Start with property_library.html (can be found by typing the filename into the query box) and use the interactive table to filter, sort, and select a microstructure with the desired properties. Search for the alphabetic code to obtain the corresponding dataset. Full description: This is a bank of 1,970 unique 3-phase electrode microstructure files. When you account for reassigning phase IDs (e.g. declare that 1=Ni and 2=pore, instead of 1=pore and 2=Ni), it actually represents 5,910 unique electrode microstructures, each of which could be considered to be either an air or a fuel electrode (e.g. declare that the phase IDs correspond to pore, Ni, and YSZ; or that they correspond to pore, LSCF, and GDC; or whatever electron-conductor and ion-conductor combination is being studied). The voxel size is 50 nm and each electrode file contains a 4x4 grid of (12.5 micron)^3 sub-volumes. If placed together in a grid, they comprise a 50x50x12.5 micron electrode (note that the interfaces between sub-volumes will be sharp; this can be mitigated via simulating annealing/relaxation). The sub-volumes can also be used individually for a reasonably sized 12.5 micron cubic region-of-interest. A user can simply consider the voxel size to be a different value to rescale the volumes (and all of their morphological features, including particle size) as desired. These microstructures were generated using DREAM3D. The general procedure is outlined in https://doi.org/10.1016/j.jpowsour.2018.03.025 The file names are an alphabetic code having to do with the input parameters used in DREAM3D when they were generated. Most users would be best served by starting with the file property_library.html or property_library_subvols.html (which lists properties for each individual subvolume). These files contain a catalogue of the actual, measured properties of every microstructure in the database. Any combination of property values can be filtered and sorted until a desired electrode is found, at which point the user can find the file corresponding to that alphabetic code. The properties in the catalogue include connected TPB density, and for each phase: phase fraction, average particle size, polydispersity of particle size, tortuosity, and connected pair-wise interfacial area. They also include what fraction of each property is connected through to the interfaces of the volume. If the desired combination of properties is not found at first, remember that the phase IDs can be re-assigned arbitrarily, e.g. swapping 1s and 2s. In fact, the database was generated with this in mind so as not to generate redundant microstructures. If the database does not contain the desired property combinations, try to search for the other possible permutations of those properties with re-assigned phase IDs. Please cite https://doi.org/10.1149/10301.0909ecst for use. Please contact the maintainer, William K. Epting, for additional information or assistance.

3D microstructure↗
DOE OSTI2021

Materials Challenges and Opportunities for Energy Generation, Conversion, Delivery, and Storage (Applied Energy Tri-Laboratory Consortium Workshop Report)

This report documents the outcomes of the Tri-Laboratory Materials Workshop that was held July 31 and August 1, 2019 to begin addressing the needs, opportunities, and challenges associated with the development, fabrication, and testing of the needed materials and components for integrated hybrid energy systems (i.e., incorporating nuclear, fossil, and renewables for electric and thermal applications). This was accomplished by assembling the research program leads and principal investigators at Idaho National Laboratory (INL), National Energy Technology Laboratory (NETL), and National Renewable Energy Laboratory (NREL), who support the research and development of new technology and system integration. The team then identified and prioritized key materials development needs. This effort was intended to enhance communications and synergy among the Tri-Lab partners. Advanced functional and structural materials are central to transformative energy technologies for energy generation, conversion, delivery, and storage. With that in mind, the workshop focused on identifying and assessing the foundational materials research needs at both the basic and applied levels. Materials challenges include the ability to withstand harsh environments, such as high temperatures and pressures, corrosion, oxidation, or irradiation while maintaining flexible mission profiles and long service lifespans. Advanced energy system material challenges and needs range from materials for the capture, upgrading/concentration, storage, and delivery of low-grade heat to materials for high temperature environments that involve liquid metals, molten salt, and very high temperature gas heat delivery and storage systems. Material improvements are needed for hybrid energy systems due to accelerated corrosion and stress-fatigue failure of materials and equipment, which results from increased frequency and amplitude of thermal, mechanical, and electrical cycling of systems components. Multifunctional materials are needed for high temperature solid-oxide fuel cells, advanced electrochemical reactors, and in-process separation. Relative to materials manufacturing, application of advanced additive and subtractive methods need to be understood to develop both thin-layer homogenous materials and materials of graded composition. Materials modeling and machine learning will be critical to accelerate the design and production of power electronics, and nuclear reactor materials and fuel, as well as to gain an understanding of beneficial materials phenomena or deleterious microstructure evolution. There is also a need for standardized models, computational structures, data reporting protocols and modeling tools across the three laboratories. This would allow consistent results, analysis, and data sharing. Combining computational capabilities between the three laboratories (e.g., hardware, software) would greatly increase computational capabilities and throughput. The workshop identified the need for laboratories to anticipate and address problems that will occur during scale-up. Laboratory work must connect with industry to ensure that research focuses on processes that are scalable and marketable. Industry input and perspective are essential to guide laboratory research to meet these requirements and deploy new technology in industrial demonstrations. Another aspect of scale-up is the integration of multiple systems since new challenges often arise at the subsystem interfaces. Establishing a scale-up manufacturing demonstration/pilot plant, potentially as an industrial user facility, would be beneficial to the laboratories and industry. That modular scale-up manufacturing demonstration/pilot plant would allow researchers to find and resolve interface problems that cannot be identified by focusing only on individual parts. Communication exchanges among the organizers, attendees, and workshop survey responses indicate that the workshop was successful in achieving its goal to identify key technology gaps and research needs. Strong positive feedback was received on the sharing of ideas, capabilities, talent, and passion to move forward on the materials-related action items.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High spatial resolution temperature profile measurements of solid-oxide fuel cells

Temperature gradients resulting from local electrochemical reactions, current distribution and geometry of gas flow channels in solid oxide fuel cells (SOFCs) create thermal stresses, localized thermophysical property gradients and uneven property evolution, contributing to SOFC degradation. This paper presents a new method to perform temperature measurements (up to 800°C) at high spatial resolutions to monitor the operation of SOFCs. Using femtosecond laser irradiation, distributed fiber sensors were hardened for high temperature environment applications. Distributed fiber sensors were embedded in interconnected plates using an additive manufacturing method to perform temperature measurements with 4-mm spatial resolution during the operation of a planar fuel cell. The measurement revealed the impact of various H 2 fuel concentrations and current loads have on temperature profiles of the SOFC tested. Temperature variation on the anode side was found to be less than 5°C, and 3°C on the cathode side. The measurements were compared to results from a multiphysics fuel cell performance model simulating similar conditions. These simulations predicted similar temperature gradients, indicating the experimental data obtained is reasonable. The model also predicts that the effect of the embedded sensor has on the local temperature will be minimal and that the gradient of temperature in the gas channels will be captured despite the separation between the sensor and the gas flow. Finally, the high spatial resolution data harnessed by these distributed fiber sensors provides experimental support for model-based design and optimization to improve the operational efficiency and longevity of solid oxide fuel cells and fuel cell assemblies.

25 ENERGY STORAGE↗
DOE OSTI2021

NETL Electrical Conductivity Relaxation(ECR) Analysis Tool

This application was developed within the solid oxide fuel cell (SOFC) work plan. It calculates the oxygen surface exchange coefficient (k) and oxygen diffusion coefficient (D) for an oxide sample using electrical conductivity relaxation (ECR) data. The tool also produces a heat map showing the associated uncertainty in fitting the ECR data for given pairs of k and D values, so the user can determine the most likely range of k and D values for the tested values. Multiple datasets for the same material can be plotted to decrease uncertainty. The tool can also simulate ECR curves for inputted k and D values and overlay the simulated curves with experimental data for comparison.

electrical conductivity relaxation↗
DOE OSTI2020

Phase field simulation of anode microstructure evolution of solid oxide fuel cell through Ni(OH) 2 diffusion

Microstructure evolution in a solid oxide fuel cell anode is strongly affected by operating condition. The detailed mesoscale evolution mechanism under operating condition is still under debate. Here we develop a phase-field model to simulate microstructure evolution through formation and diffusion of gaseous Ni(OH)2. We studied the coarsening kinetics and redistribution of Ni under different steam distributions and compare it to that under pure hydrogen condition. Overall, the results suggest that although the presence of a steady gradient of steam leads to redistribution of Ni, Ni(OH) 2 formation and diffusion do not significantly change the Ni coarsening rate under strictly humid conditions, contrary to commonly reported hypotheses. It is concluded that competing mechanisms other than Ni(OH) 2 diffusion must be responsible for the experimentally observed Ni redistribution and enhanced coarsening under humid conditions.

25 ENERGY STORAGE↗